Kohler ODEON K-8766 User manual

BEFORE YOU BEGIN
ODEON
INSTALLATION INSTRUCTIONS
VITREOUS CHINA P/S-TRAP TOILET
S-TRAP 305mm K-8766 LM
P-TRAP 180mm K-8711 LM
ŸPlease read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. Follow
the sections that pertain to your particular installation. This will help you avoid costly mistakes. In addition to Proper installation,
read all operating and safety instructions.
ŸAll information in these instructions is based upon the latest product information available at the time of publication.
Kohler India reserves the right to make changes in product characteristics, packaging, or availability at any time without notice.
ŸThese instructions contain important care, cleaning, and warranty information- please leave instructions for the consumer.
ORDERING INFORMATION
Odeon S-Trap 305mm Toilet...............................K-8766LM Odeon P-Trap 180mmToilet..............................K-8711LM
Includes seat.................................................K-8827LM Includes Seat.............................................K-8827LM
Includes bowl................................................K-8767LM Includes bowl.............................................K-8709LM
Includes tank.................................................K-8710LM Includes tank..............................................K-8710LM
NOTES
ŸObserve all local plumbing and building codes.
ŸShut off the water supply.
ŸEnsure that the new drain and shut-off valve have the correct roughing-in dimensions. See Fig.#1.
ŸBe very careful while working with vitreous china products. Vitreous china can break or chip if the bolts or nuts are overtightened, or
if carelessly handled.
ŸCarefully inspect the new fixture for any sign of damage.
ŸFixture dimensions are nominal and conform to tolerances established by ASME Standards (A112. 19.2-2003)
TOOLS AND MATERIALS REQUIRED
(Not supplied)
Ÿ254mm adjustable wrench Level Screwdriver
ŸMetal file (file cut) Hacksaw Straight pipe coupling
ŸTape measure Putty knife Connection packaging
ŸTubing cutter Toilet supply shut-off valve. 15mm (½") recommended
WARNING: Risk of external leakage. The valve nut has been factory-tightened. Wrench tighten
1/4 turn past finger tight.
NOTICE: If no shut-off valve exists, install a shut-off valve below the tank before installing the new toilet.
Flexible hose are recommended to connect the supply line to the fill valve. If you use a rigid connection, take care not to apply side
forces to the bottom of the fill valve.
1037406-LM01-B -1-

ROUGHING-IN
INSTALLATION
1. REMOVE EXISTING TOILET
Turn off water supply. Flush the toilet and use a sponge to remove the remaining water from the tank and bowl. Disconnect the supply
shut-off valve (if present) and remove the old tank and bowl.
2. ASSEMBLE TANK BOLTS & WASHERS
Slip bolt heads into mounting hole on bottom of tank. Place large foam washer on base of flush valve. See Fig. #2a. Place tank on
bowl and attach with nuts & washers from under bowl. See Fig. #2b.
1037406-LM01-B -2-
Fig.#1
202
786 10
390
475
305 102
13
S-trap 8766LM
733
350
257
364
163
155
430
390
704
340
262
360
166
155
430
391
202
782 10
386
90
396
180
160
102
P-trap 8711LM
ŸAll dimensions in mm. Fixture dimensions are nominal and conform to tolerances as per ASME Standard A112. 19.2M.
ŸProduct pictures shown are representative only, actual products may vary.
ŸKohler reserves the right to make changes in product characteristics, packaging or availability at any time without notice.

Fig.#2a
Fig.#3a Fig.#3b
3. SELECT P-TRAP OR S-TRAP to install your toilet according to the drain and shut-off valve’s Roughing-in dimensions.
1037406-LM01-B -3-
4. INSTALL THE TOILET & CONNECT WATER SUPPLY
Place the toilet in its final location. Use plastic drill guide and 8mm drill bit to drill floor mounting holes for installation over concrete. Use
4mm to 4.5mm drill for wood floor installation. See Fig.#4a.
Install anchors and caps.
WARNING: Do not over tighten floor bolts, as damage to the vitreous can occur.
NOTE: Do not use white cement or high lime content cements to install this toilet. The expansion of cement due to a rise in
temperature may make the toilet crack or cause damage. Kohler is not responsible for any damage caused by installation with the
use of cement.
3
S-trap installation P-trap installation
100
120
180
305
50
305
100
120
50
180

4Connect fill valve to water supply with hose only.
NOTE: use hose only, length:
200-300mm minimum
(Not provided.)
4
Fig. #4a
5. CHECK WATER LEVEL
Turn on water supply, check for leaks. If necessary, adjust black float adjustment clip, and sliding float up or down on metal float rod
until water level at marked level line.
Make sure the arrow on the green float on the white flush valve is secure and pointing to # . (Fig. )
5A
1037406-LM01-B -4-
Fig. #5
5B
Float
5A
Float
Adjustment clip
6
65B

6. ADJUST OVERFLOW HEIGHT (If necessary)
Adjust overflow tube so that the top is 20mm above the waterline. Push locking mechanism to the side and adjust tube height. Push
locking mechanism back into position to lock tube height. See Fig. #6.
7. CONNECT PUSH BUTTON
Remove the locknut & place the push button assy. through the hole on lid cover of tank & fix with locknut.
Put green & grey push rods into corresponding buttons & trim length as per requirement.
Install the button rod assembly in respective position in the push button.
Flush the toilet several times and check all connections for leak.
1
2
3
4
1037406-LM01-B -5-
8. Install seat with hardware provided. See Installation Instructions provided with seat.
Fig. #6
maxi
Fig. #7
12

1037406-LM01-B -6-
SYMPTOMS PROBABLE CAUSES CORRECTIVE ACTION
1. Float valve turns on/off
TROUBLESHOOTING CHART
by itself without toilet
being flushed
2. Float valve continues
to run, allowing water
to enter tank.
3. Incorrect water level
height.
4. Long or noisy tank fill
5. Poor flush.
6. Toilet overflows.
A. Flush valve seal worn, dirty or damaged.
A. Float height incorrect.
A. Plugged valve inlet or supply line.
A. Water usage is too low.
B. Trapway obstructed.
C. Soil pipe or vent is obstructed.
D. Supply shut-off valve not fully open.
A. Toilet trapway is obstructed.
B. Soil pipe or vent is obstructed.
A. Inspect, clean and, if necessary replace seal.
A. Adjust float by squeezing float adjustment clip,
and sliding float up or down on float rod until
water leve is at marked water line.
A. Perform corrective action 2.A.
A. Adjust the water tank level.
B. Unclog trapway.
C. Clear obstruction from soil pipe or vent.
D. Open supply shut-off valve.
A. Use plunger to unclog.
B. Clear obstruction from soil pipe or vent pipe.
A. Foreign particles lodged under the float valve
seal (located under float valve cap)
B. Float valve seal (located under float valve cap)
may be cracked or split.
C. Tank water level set above overflow level.
A. Shut off water supply; remove float valve cap
assembly by rotating 1/8 turn
counterclockwise. Cover uncapped lower
valve unit with an inverted cup (holding it to
prevent overspray), and turn water on and off
a few times. Clean float valve seal surface
(located under float valve cap). Replace float
valve cap assembly by engaging lugs and
rotating 1/8 turn clockwise. Turn water on.
Install filter in supply line to prevent recurring
problems.
B. Replace seal.
C. During fill cycle, hold float under water a few
seconds to allow it to fill with water ballast.
Adjust float by squeezing float adjustment clip,
and sliding float up or down on float rod until
water level is at marked water line.
TROUBLESHOOTING CHART
IMPORTANT CONSUMER INFORMATION
CONSUMER RESPONSIBILITIES
If you live in a hard water area, make certain that the holes in the toilet rim are kept clean to ensure proper bowl flushing.
Toilet bowl cleaners should be used at least once a week. Use a long-handled brush to clean the rim holes, and to
clean as far into the trap as possible to prevent mineral deposits from forming.
Most toilet bowl cleaners are not harmful to the vitreous china surface of the toilet bowl. Please follow the bowl cleaner
manufacturers instructions carefully.
Do not use abrasive cleaners or solvents.
WARNING: Risk of property or product damage.
Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in the
tank. This damage can cause leakage and property damage.
Kohler Company shall not be responsible or liable for any damage to these tank fittings caused by the use of cleaners
containing chlorine (calcium hypochlorite)

1037406-LM01-B -7-
(This Page is left blank intentionally.)

1037406-LM01-B -8-
Toll Free : 1800 4KOHLER