Kohler K-29918T-NSHC User manual

-1-
VEIL
INSTALLATION INSTRUCTION
WALL-HUNG TOILET
3.0/4.5
K-29918T-NSHC
BEFORE YOU BEGINBEFORE YOU BEGIN
ORDERING INFORMATION
Veil WH Toilet W/O Seat
(HT300 P, 3.0/4.5) .........................................K-29918T-NSHC
Veil Bowl ......................................................K-5723T-HC
Hydro-tower 300 PNE IWT
(HC, 3.0/4.5L) ...................................K-20010T-VLWP-NA
C3 Toilet Seat With Bidet Functionality (Not Provided)
..............................................K-29918T-NSHC
...................................K-5723T-HC
300
3.0/4.5 ...........................................K-20010T-VLWP-NA
C3 ( )
·
·
·
·
·
Fixture dimensions are nominal and conform to tolerances
established by ASME Standards (A112.19.2-2018).
The product complies with Q/KCI-006-2018 and GB
25502-2017.
Please read these instructions carefully to familiarize
yourself with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
All information in these instructions is based upon the
latest product information available at the time of
publication. Kohler China reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning, and
warranty information -
.
please leave instructions for the
consumer
·
·
·
·
·
-
ASME (A112.19.2-
2018)
Q/KCI-006-2018 GB 25502-2017
No.2 KOHLER ROAD, SANSHUI CENTRAL INDUSTRIAL PARK, LEPING TOWN, SANSHUI DIST., FOSHAN, GUANGDONG, PRC POST CODE 528137
2 528137
8# MENGSHAN RD, ECONOMIC DEVELOPMENT ZONE OF HUANTAI, ZIBO, SHANDONG, CHINA 256410
8 256410
NO.1 KOHLER STREET, ECONOMIC DEVELOPMENT ZONE OF FAKU COUNTY, SHENYANG LIAONING PROVINCE, PRC 110400
1 110400
:
POST CODE:
POST CODE:
SAFETY WARNINGS
Kohler products are precision-engineered and should give
continued superior and safe performance, provided:
1. They are installed, commissioned, operated and
maintained in accordance with the recommendations given
in this Manual.
2. Periodic attention is given, as necessary, to maintain the
product in good functional order. Recommended
guidelines are given in the section.
Carefully inspect the new fixture for any signs of damage.
When installing Kohler Products, manufacturers guidelines for
power tool safety should be followed.
MAINTENANCE
1.
2.
©
©
Copyright Kohler China Investment Co., Ltd. 2021
2021
1461371-T01-B

-2-
ROUGHING-IN
RECOMMENDED TOOLS AND MATERIALS
(Not Supplied)
·
·
·
·
·
·
·
·
·
·
·
·
·
·
Safety Glasses
Tape Measure
Putty Knife
Pipe Wrench
Adjustable Wrench
Tubing Cutter
1/2" Nut Driver or socket
Pencil
Waxseal
Supply Shut-off Valve
Level
Screwdriver
Sponge
Sealant
·
·
·
·
·
·
·
·
·
·
·
·
·
·
1/2"
UNIT mm
Reference Value
Kohler reserves the right to change marked dimensions without prior notice.
Fig.#1
1
55
140 285 385
352
473
554
345
400
180
353
102
135
1/2" BSP
SPECIFICATION
Plumbing Connections
Recommended inlet connections are 1/2 BSP."
1461371-T01-B

-3-
INSTALLATION
Recommended tanks for 3/4.5L
In-wall Tank K-20010T-VLWP-NA (w/o iron rank) And In-wall
Tank plate K-23056T-*, K-20341T-PNE-*, K-75890T-PNE-*,
K-23055T-PNE-*. (Need separate purchase for plate)
3/4.5L
K-20010T-VLWP-NA( )
K-23056T-* K-20341T-PNE-* K-75890T-PNE-* K-
23055T-PNE-*
Install the Toilet
Fig.#2
2
Fig.#3-a
3-a
1. Install Flushing Mechanism
Turn the water supply off before installing the new toilet.
Install the concealed tank system in wall before
decorating the wall.
Install the tank system per tank's installation instructions.
·
·
·
Recommended rack dimension(Fig.#3-b)
1) Rack height should be adjust between 0~200mm.
2) Rack should support weight 400kg.
3) Tank height should be adjusted according to ceramic
installation requirements.
1.
( 3-b)
1) 0~200mm
2) 400kg
3)
·
·
·
Fig.#3-b
3-b
320
135
35
180
1461371-T01-B

-4-
3. Attach Connection Pipe
3.1. Install the inlet pipe to the lavatory as shown, and mark
on the pipes at the back side of the tank with a ruler and
a pencil, and reserve appropriate space according to the
distance from the back of the tank to the inlet hole on the
wall.
3.
3.1.
2. Set The Spacing Of The Bowl
After you install the tank, be careful to set the spacing of the
bowl on wall according to the dimensions as shown.
2.
Fig.#4
4
Fig.#5
5
Fig.#6
6
180 2
135 2
320
1
Carrier Studs
Unit: mm
:
25 2
Inlet Pipe
Drainage Pipe
3.2.
Inlet Pipe
Reserved Space
Drainage Pipe
3.2. Eliminate unwanted part of the inlet pipe according to the
marks of reserved space ,and rasp a smooth surface with
files.
1461371-T01-B

-5-
3.3. As shown, pull the inlet pipe of the Bidet seat through the
bowl and connect it to the valve hose connector on the
iron rack. Pull the plug of the Bidet seat through the bowl
and connect it to the socket on the iron rack and then fix
the Bidet seat.
Seat hardware: See fig.8
3.3. ( )
8
Fig. #9
9
Fig. #10a
10a
Fig. #10b
10b
4. Place the new bowl on the wall through the carrier. Wrench
the nut to tighten and make them attached securely. See
Fig. 9.
Torque for tightening nuts is recommended to be within
the range from 8 Nm to 12 Nm.
·
4.
9
8Nm 12Nm
·
Adjust to horizontal and finish tightening. See Fig. 10a.
Apply sealant to make sure the bowl's edge seals to the wall.
See Fig. 10b.
10a
10b
Finished Wall
Fig.#7
7
Fig.#8
8
1461371-T01-B

-6-
Install the toilet seat according to the toilet seat installation
instructions.
5. Install The Side Panels
The left panel (L) and right panel (R) are not
interchangeable and they shall be respectively fixed onto the
left side and right side of the bowl as shown in Fig.11.
Align the iron sheet on one side panel with the magnet
on the bowl. Fix the side panel onto the bowl and adjust it
with hand to the desired position.
NOTE:
!
5.
LR
11
!
!Repeat for the second side panel. !
Cleaning
Caution! Risk of product damage.
Caution! Risk of product damage.
Caution! Do not use in-tank cleaners.
Many cleaners
contain abrasive and chemical substances, and should
not be used for cleaning stainless steel, enamel,
plated or plastic fittings. These finishes should be
cleaned using a mild washing up detergent or soap
solution, rinsed and then wiped dry with a soft clean
cloth.
Most toilet bowl
cleaners are not harmful to the vitreous china surface
of the toilet bowl. Please follow the bowl cleaner
manufacturer,s instructions carefully.
Products
containing chlorine (calcium hypochlorite) can
seriously damage fittings in the tank. This damage can
cause leakage and property damage.
CAUTION: Don t use any cement while installing
the toilet.
WARNING: Risk of product damage.
Heat expansion of the toilet may damage
the feet of the toilet. Kohler will not be responsible for
any damage because of using cement.
Do not throw into the toilet what is easy to block it,
such as newspaper, paper pilch, sanitary towel.
Do not bump the vitreous china with great force to
prevent it from damaging and leaking.
Do not use the product in the water below 0 C.
o
'
Please do not use hard materials (like
scouring pad) to clean product surface, especially the
product logo.
CAUTION:
0C
o
USER MAINTENANCEUSER MAINTENANCE
Magnet
Iron Sheet
Fig. #11
11
1461371-T01-B

-1-
HYDRO-TOWER 300 300
INSTALLATION INSTRUCTIONS
IN-WALL TANK
N
K-20010T-VLWP/K-20341T-PNE/K-75890T-PNE
K-23055T-P E/K-23056T/K-23056TW
!
!
!
!
!
!
!
Read installation guide in illustration and word file carefully, and install the tank according to instructions in the guide to avoid
product damage and installation inconvenience caused by inappropriate operation.
All data contained is based upon the last product information available at the time of publication. Kohler Company reserves
the right to implement changes of product characteristics, packaging and availability at any time without further notice.
Do not apply erosive cleanser and solvent in the tank, which will damage tank spares and result in leakage in the tank.
Kohler will not be responsible for any damage related to above mentioned cleanser or solvent. Mild detergent can be used.
Do not apply spares that are not provided by Kohler, and please note that glass adhesive tape shall not be applied to the
installation of Kohler spares. Kohler will not be responsible for any damage related to installation with spares not provided by
Kohler.
This product complies with GB26730-2011.
Please mount the tank frame on the solid wall and wall thickness should exceed 80mm.
During build the front wall of tank, please take protective measure and don't squeeze the tank body directly with concrete,
brick or other hard materials.
!
!
!
!
!
!
!
GB26730-2011
80mm
BEFORE YOU BEGINBEFORE YOU BEGIN
KOHLER CHINA INVESTMENT CO., LTD NO.158, JIANG CHANG SAN ROAD,
JING'AN DISTRICT, SHANGHAI, PRC POST CODE: 200436
( ) 158 200436
©
©
Copyright Kohler China Investment Co., Ltd. 2020
2020
Ordering Information
HYDRO-TOWER 300 PNE IWT(HC,3.0/4.5L)........................................................................................................K-20010T-VLWP
PEBBLE PNEUMATIC IN-WALL TANK FACEPLATE (NOT SUPPLIED) ................................................................K-20341T-PNE
LYNK PNEUMATIC FACEPLATE (NOT SUPPLIED) ...............................................................................................K-75890T-PNE
MODERN LIFE SMALL FACEPLATE (NOT SUPPLIED) .........................................................................................K-23055T-PNE
BEAM SENSOR FACEPLATE (NOT SUPPLIED) .............................................................................................................K-23056T
BEAM SENSOR FACEPLATE (NOT SUPPLIED)..........................................................................................................K-23056TW
300 3.0/4.5 ( HC) .........................................................................................K-20010T-VLWP
( )( )........................................................................................................................K-20341T-PNE
( )..................................................................................................................................K-75890T-PNE
( ).........................................................................................................................................K-23055T-PNE
( )...................................................................................................................................K-23056T
( )................................................................................................................................K-23056TW
!
!
!
!
!
Function Explanation
!
!
!
!
!
Anti flow-backwards
Adjustment of inlet water level
Adjustment of flushing volume
Single/double gear
Assemble, disassemble and
maintenance can be done without
tools.
flushing
1381424-T01-B

-2-
!
!
Design And Installation Concept Of In-wall Tank
!
!
Installation of in-wall tank is much easier and nice-looking comparative to that of traditional tank. Meanwhile, the space
layout will be more reasonable due to the application of in-wall tank pipes and connectors.
The most remarkable advantage of in-wall tank is that the installation will never be limited to certain area, and can be
installed wherever as you wish, which will make the bathroom layout more reasonable and nice-looking, and make good use
of every inch of the bathroom space.
Advantages Of In-wall Tank
!
!
!
!
!
!
!
!
Made of macromolecular materials that prevents corrison and leaking.
Will not affect the structure of the wall and provides excellent sound insulation.
Easy installation and time efficient.
.
.
Clean, garbage free, and space .
Advanced water tank fitting, which makes possible the adjustment of the water discharge and double flush.
Extra-thin shell of the tank helps to save a lot of space and fit for any walls.
Do not need to prepare any other spare parts
Easy maintenance and servicing
saving
SPECIFICATIONS
Liter per flushing
Temperature
Water Supply
Environmental temperature: 1 ~55
Water temperature: 1 ~45
°C °C,
°C °C
°C °C
°C °C
1 ~55
1 ~45
Min water supply: 0.02MPa (dynamic pressure)
Max water supply: 0.74MPa (static pressure)
0.02MPa ( )
0.74MPa ( )
K-20010T-VLWP
Full flushing volume: 4.5L
Half flushing volume: 3.0L
4.5L
3.0L
!
!
!
!
!
!
!
!
RECOMMENDES TOOLS AND MATERIALSRECOMMENDES TOOLS AND MATERIALS
!
!
!
!
!
!
!
!
!
!
!
!
!
Open end/adjustable wrenches
Allen wrench
Knife
File
Hacksaw
Masonry
Level
Screw driver
Insulation tape
Tape measure
Seal tape
Bushing
Lubricant
!
!
!
!
!
!
!
!
!
!
!
!
!
/
1381424-T01-B

-3-
ROUGHING-IN
UNIT: mm
Reference Value K-20010T-VLWP
478 3
1098 4
Height Suggested
1150
100 3
52~230
205 3 681 4
230 3
180 3
90 0.5
45~95
35 2
269 5
1066 4 1048 4
88 2
438 3 90~142
Air hose
Finished Floor
18~62
Air hose
Pinch
plate
Suggested faceplate
installation area
R1000mm
Installed with
K-20341T-PNE
K-20341T-PNE
Method one:
Press from front
Method two:
Remote plate installation
Air hose
Suggested faceplate
installation area
R1000mm
Method three:
Remote installation of mask
225 1 225 1
160 1
160 1
K-20341T-PNE K-75890T-PNE
160 1
225 1
K-23056T/K-23056TW
K-23055T-PNE
155.5 1
51 1
Connector G1/2
(Customer inlet
hose connection)
G1/2
()
Connector G1/2
(Connect to Bidet
seat water supply pipe)
G1/2( )
Corner valve inlet G1/2
(Customer inlet hose
connection)
G1/2
()
Socket for Bidet seat
Note: Pre-arrange power line in the wall which is hard line of 1mm -2.5mm and has
GFCI or ELCB of or above 220V~, 50Hz, 10A. Plug in the socket and fix it onto the iron
rack after tank is installed.
1mm -2.5mm 220V~,
50Hz, 10A
22
22
Floor Discharge Installation Method
Three discharge pipe installation methods based on actual
situation: A, B, C, adjust position by screw driver. Snap
discharge pipe lower end into discharge port.
ABC
B
A
Discharge
Elbow
Discharge
Elbow
Water
Tank
Bracket
Water
Tank
Bracket
Drain outlet 90mm, welding
90mm
Drain outlet 110mm
110mm
Kohler reserves the right to change marked dimensions without prior notice.
C
Discharge
Elbow
Water
Tank
Bracket
Drain outlet 110mm, welding
110mm
1381424-T01-B

-4-
INSTALLATION
Way of Installation
In-wall tank with frame
()
In-wall Tank With Frame
()
Installation For In-wall Tank With Frame
A. Installation of In-wall Tank
()
A.
1. Remove in-wall tank from packing box. Remove cover
board inside water tank first as shown. Then remove
support block and plug above bracket assembly.
1.
Cover
Cover
Supporting Board
Plug
2. Loose hex-head screw and adjust mounting bracket height
as shown in Fig A.
Loose hex-head screw and adjust supporting feet height as
shown in Fig B.
mounting bracket and supporting feet shall be adjusted
per customer ideal height. Use leveler to ensure the balance
of steel bracket.
Note:
2. A
B
Screw
Screw
Hex-head
Wrench
Medium
Allen Key
Adjustable
Bracket
Mounting
Bracket
A
B
1381424-T01-B

-5-
3. Drill four holes with diameter of 10mm and depth of 80mm
with churn drilling as shown.
A. Fill the bulge nail into the instruction hole on the wall, fix
the fixing frame to the bulge nail, adjust the gasket and
tighten the nut.
B. Fill the bulge nail into the instruction hole, fix the
adjustable bracket to the bulge nail, adjust the gasket
and tighten the nut.
3. A B 10mm 80mm
A.
B.
Adjustable Bracket
Mounting
Bracket
A
B
Bulge Screw
Bulge Screw
Gasket
Gasket
Nut
Nut
4. Tighten the nut with the wrench as shown in illustration A.
Tighten the nut with the wrench as shown in illustration B.
4. A
B
A
B
Nut
Nut
Wrench
Wrench
B
C
A
Discharge
Elbow
Discharge
Elbow
Discharge
Elbow
Water Tank
Bracket
Water Tank
Bracket
Water Tank
Bracket
Drain outlet 90mm, welding
90mm
Drain outlet 110mm
110mm
Drain outlet 110mm, welding
110mm
B. Floor Discharge Installation Method
B.
1. Three discharge pipe installation methods based on actual
situation: A, B, C, adjust position by screw driver. Snap
discharge pipe lower end into discharge port.
1. ABC
1381424-T01-B

-6-
2. Connect tap water braided tube on the top of water tank for
water supply as shown.
Note: 1. Ensure water tank internal valve is OFF.
2. Suggestion: connect a temporary rubber or plastic
hose on valve, flush water supply pipeline. Ensure
water is clean, no residual sand stone or fouling
inside pipeline.
2.
1.
2.
Water Pipe
Connecting Pipe
3. Install tap water braided tube on angle valve for water
supply as shown.
Note: 1. Ensure valve is OFF.
2. Suggestion: connect a temporary rubber or plastic
hose on valve, flush water supply pipeline to ensure
water is clean, no residual sand stone or fouling
inside the pipeline.
3. The valve and hose are for connecting the Bidet seat,
please do not remove.
3.
1.
2.
3.
4. As shown, pull the pre-arranged power line through the
hole of the iron rack and connect to the socket (inside tank
package). Fix the socket onto the iron rack.
4.
Valve
Hose Hose
Valve
Tap water braided tubeTap water braided tube
Cable
Screw M3X0.5
M3X0.5
Socket
5. As is shown, fix the EPE block onto the drain hole and inlet
hole.
5. EPE
Inlet Hole
Drainage Hole
Tank Bracket
EPE Block
EPE
1381424-T01-B

1) K-20341T-PNE/K-75890T-PNE Access Panel
Installation Methods:
There are three ways to install access panel:
Method one: Press from front
Method two: Remote plate installation: fix four plates
with screws
Method three: Remote installation of mask
1)
:
K-20341T-PNE/K-75890T-PNE
18~62
Method one:
Press from front
Method two:
Remote plate installation
Method three:
Remote installation
of mask
Air hose
Air hose
Pinch
plate
Suggested faceplate
installation area
R1000mm
Suggested faceplate
installation area
R1000mm
6. According to different faceplates,there are different
installations of access panel as below.
6.
-7-
Mask
Screw
Water Tank
Protective Cover
A. Method one: Install mask when pressing from front
a) Install the mask in the block screen of the tank, and
tighten the screw to fix the mask to the tank.
A.
a)
b) Cut apart the cable of the air hose and pull it out
from the mask.
b)
B. Methods two and three: During remote installation, fix
the cover onto the tank and pull the air hose to the
panel. Reserve access panel at front to ensure
removal and installation of cover.
B.
Cover
At least 80mm gap reserved
80mm
Air hose
Pinch plate
Finished wall
Supporting
Board
Air hose
Finished
wall
Fix Mask Onto Wall
10 Hole through hose
10
10 Depth 16,
Space reserved
10 16 72
7~20mm recommended
7~20mm
Cable
Method two: During remote plate installation,
7~20mm thickness is recommended for the wall of
the pinch plate and at least 80mm gap is reserved.
Method three: During remote installation of mask, 4
holes with diameter of 10mm and depth of 16mm are
needed to be reserved at the locating hose. Drill
10mm holes through air hose on the side of mask.
Recommended installation hole size of
X mm to remote plate installation.201 136
7~20mm 80mm
4 10mm 16mm 10mm
Xmm201 136
+2
0
+2
0
+2
0
+2
0
201
136
+2
0
+2
0
1381424-T01-B

-8-
+2
0
+2
0
+2
0
+2
0
2) K-23055T-PNE access panel installation and installation
hole size
2) K-23055T-PNE
There is only remote installation with K-23055T-PNE,
During remote installation, fix the cover onto the tank
and pull the air hose to the panel. Reserve access panel
at front to ensure removal and installation of cover.
Recommended installation hole size of
146 .X41 mm
146 X 41 mm
41
146
+2
0
+2
0
Pinch Plate
Wall Thickness 7~40mm
7~40mm
Adjust length of
pinch plate in
accordance with
wall thickness
At least 80mm gap reserved
80mm
3) K-23056T/ access panel installation
3) K-23056T/
K-23056TW
K-23056TW
a) There is only press from front installation with K-
23056T/K-23056TW.
a) K-23056T/K-23056TW Mask
Screw
Water Tank
Protective Cover
c) Cut apart the cable of the air hose and pull it out from
the mask.
b) Install the mask in the block screen of the tank, and
tighten the screw to fix the mask to the tank.
b)
c)
Cable
C. Installation of P-trap
C.
1. Insert drainage pipe with inner diameter 110mm into
drain elbow and weld.
1. 110mm
Water Tank Bracket
Drainage Pipe
1381424-T01-B

2. As is shown, fix the EPE block onto the drain hole and inlet
hole.
2. EPE
EPE Block
EPE
EPE Block
EPE
-9-
Water Inlet
Drainage Hole
Water Tank Bracket
Mask
D. Installation of Toilet
D.
1. Install the inlet pipe to the lavatory as shown, and mark on
the pipes at the back side of the tank with a ruler and a
pencil, and reserve appropriate space according to the
distance from the back of the tank to the inlet hole on the
wall.
1.
Inlet Pipe
Drainage Pipe
2.
Inlet Pipe
Reserved Space
Drainage Pipe
2. Eliminate unwanted part of the inlet pipe according to the
marks of reserved space ,and rasp a smooth surface with
files.
3. EPE
3. As shown, remove the EPE after finishing the wall. Screw
in the long screw as desired. Eliminate unwanted mask
with a sharp knife, if there is mask. Sort the hose on the
valve.
Long Screw
1381424-T01-B

-10-
3. Install the big and small leak-proof gaskets on inlet pipe
and outlet pipe ,then install it to corresponding pipes on the
toilet tank.
3.
Small Leak-proof Gasket
Inlet Pipe
Drainage Pipe
Big Leak-proof Gasket
4. As shown, pull the inlet pipe of the Bidet seat through the
bowl and connect it to the valve hose connector on the iron
rack. Pull the plug of the Bidet seat through the bowl and
connect it to the socket on the iron rack and then fix the
Bidet seat.
4.
48mm-58mm
Long Screw
Lubricant
5. 48mm-58mm of the long screw shall be reserved outside
the wall as shown in the illustration. if the long screw
outside the wall is not long enough or much longer than
that needed, it should be adjusted with screwdriver or by
hand. Then apply lubricant to drainage pipe and limber
pipe to ensure a smooth installation.
Note: 1. Make sure the leakage protection of the valve and
Bidet seat plug is turned on before bowl installation;
2. Do not get caught with the hose and wire of the Bidet
seat during bowl installation.
5. 48mm-58mm
1.
2.
6. Install the toilet as shown in the illustration, and use a spirit
level to ensure the lavatory to remain level.
6. Spirit Level
Gasket
Long Screw
Reversed Lock
Hexagonal Nut
Decoration Cap
7. Install the reserved lock, gasket, hexagonal nut and
decoration cap onto long screw according to the order
shown in the illustration.
Please refer to the installation instructions of toilet.Note:
7.
1381424-T01-B

-11-
E. Faceplate Installation
E.
1)
1)
OPEN
When tighten four locknuts on supporting board, adjust
to "OPEN" mark as shown.
Supporting Board
Locknut
Fixing Lock
According to different faceplates, there are different faceplate
installations as below:
1. K-20341T-PNE/K-75890T-PNE installation
1. K-20341T-PNE/K-75890T-PNE
Supporting Board
Locknut
2) Tighten four screws to "LOCK" mark after installing
supporting board as shown.
2) LOCK
Faceplate
Faceplate
Supporting
Board
Lock
Connect to air hose
3) Install the full flush air hose and half flush air hose to the
cover.
Cut the excessive parts of the air hose if
necessary and fix it onto the tank fastener.
Put the lock on the cover directly on the reversed
lock on supporting board, then push the cover and lock
it. The installation shall begin from bottom to top.
Note:
3)
Fastener
1381424-T01-B

-12-
4) It is ready to use when connected to water supply after
installation.
Reserve access panel at front of the tank in
remote installation.
Note:
4)
Half Flush Button
Full Flush
Button
2. K-23055T-PNE installationn
2. K-23055T-PNE
Up
Air Hose
Faceplate
1) .
1)
Suggested faceplate fixed frame installation direction
2) .
2)
Connect air hose to faceplate from water tank
3
2
1
3
2
1
Half Flush Button
Full Flush Button
3)
3)
Insert faceplate into faceplate fixed frame with half flush
upward. Installation is completed.
4) It is ready to use when connected to water supply after
installation.
Reserve access panel at front of the tank in remote
installation.
4)
5)
5)
How to remove.
Push Up
Pull Out
Pull Out
1381424-T01-B

-13-
3. K-23056T/K-23056TW installation
3. K-23056T/K-23056TW
1) Transformer Installation
Fix the transformer onto the wall, as illustrated, the
output connector of transformer(with 2 core female
connector) through the tube(suggestion: tube inner dia.
16~ 20) into tank. Connect the input terminal of
transformer(black) with power supply 220V/110V AC.
Customer can use the PVC pipe for wiring.
Don't mistake the input and output
terminal, or it may cause damage to the product.
Insulation measures must be taken at the
connection. Otherwise, short-circuit current may
occur and damage the transformer.
Warning:
1)
( 2 ) ( 16~ 20)
( ) AC220V/110V
Ceiling
Low-voltage AC
Transformer Output
Connector (In Tank)
()
Output AC 6V
AC6V
Input AC 220V/110V (Black)
AC220V/110V ( )
Transformer Assy.
Brushing Pipe
2) Faceplate Installation
A. When tighten four locknuts on support board, adjust
to "OPEN" mark as shown.
B. Tighten four screws to "LOCK" mark after installing
support board as shown.
2)
A.
"OPEN"
B. "LOCK"
Supporting Board
Locknut
Fixing Lock
Supporting Board
Locknut
1381424-T01-B

-14-
C. Install air pump to faceplate, connect emergency
flush air hose to outlet pipe in faceplate. Connect
output signal cable and input signal cable together,
and tighten nut.
C.
Emergency Flush Air Hose
Rib A
A
Slot B
B
Slot A
A
Rib B
B
Ribs on air pump should be assembled into slots on faceplate
(A-A/B-B)
Input Signal
Cable
Input Signal Cable
D. Connect big flush air hose and half flush hose to
outlet joint in air pump. Connect power output cable of
transformer and power input cable of faceplate
together, and tighten nut. Put the lock on the cover
directly on the reversed lock on support board, then
push the cover and lock it. The installation shall begin
from bottom to top.
NOTE: Cut the excessive parts of air hose if
necessary and fix it onto the tank fastener.
D.
Faceplate
Supporting
Board
Faceplate
Lock
Transformer Power Output Cable
Faceplate Power Input Cable
Full Flush Air Hose
Half Flush Air Hose
Half Flush
Full Flush
Manual Flush
1381424-T01-B