Kohler Karess S-TRAP K-5331T-S Datasheet

Karess
INSTALLATION INSTRUCTIONS
VITREOUS CHINA TWO-PIECE TOILET
S-TRAP 305mm K-5331T-S
S-TRAP 400mm K-5471T-S
-1-
, 2013
Copyright Kohler China Ltd., 2013
NOTES
·
·
·
·
·
·
·
·
·
·
Observe all local plumbing and building codes.
Shut off the water supply.
Seat post holes are on 140mm (5-1/2") centers.
51mm (2") passageway.
Water depth from the rim is 165mm.
Ensure that the new drain has the correct roughing-in
dimension. This toilet has a 305/400mm roughing-in
dimension. .
Closet flange must be 305 mm on-center from wall.
Carefully inspect the new fixture for any sign of damage.
For new construction, refer to the dimensions in
for locating the shut-off valve.
Fixture dimensions are nominal and conform to tolerances
established by ASME Standards (A112.19.2-2008).
: Handle vitreous china products very carefully.
Vitreous china can break and chip if you overtighten
bolts and nuts.
. The fill valve
nut has been factory-tightened to design specifications.
If re-tightening is required, wrench tighten one turn
past finger tight .
See Fig. #1
Fig. #1
WARNING: Risk of personal injury or product
damage
WARNING: Risk of external leakage
/400
·
·
·
·
·
·
·
·
·
·
140mm
51mm
165mm
305/400mm( 1)
305 mm
1
ASME A112.19.2-
2008.
/400
·
·
·
Please read these instructions carefully to familiarize
yourself with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
All information in these instructions is based upon the
latest product information available at the time of
publication. Kohler China reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning, and
warranty information -
.
please leave instructions for the
consumer
·
·
·-
ORDERING INFORMATION
Karess 3/4.8L Two-piece Toilet 305mm..................K-5331T-S
Includes Tank.......................................................K-5776T
Includes Bowl.......................................................K-5773T
Includes Quiet-close Toilet Seat.....................K-4141T-2P
Karess 3/4.8L Two-piece Toilet 400mm..................K-5471T-S
Includes Tank.......................................................K-5776T
Includes Bowl.......................................................K-5499T
Includes Quiet-close Toilet Seat.....................K-4141T-2P
3/4.8 305mm ...............................K-5331T-S
..................................................................K-5776T
..................................................................K-5773T
.........................K-4141T-2P
3/4.8 400mm ...............................K-5471T-S
..................................................................K-5776T
..................................................................K-5499T
.........................K-4141T-2P
1207474-T01-A

TOOLS AND MATERIALS REQUIRED
(Not supplied)
·
·
·
·
·
·
·
·
·
·
·
254mm (10") adjustable wrench
305mm (12") pipe wrench
Metal file (file cut)
Tape measure
Tubing cutter
Level
Hacksaw
Putty knife
Screwdriver
Supply pipe, at least 14" (356mm) long
Toilet supply shut-off valve, 10mm(3/8 ) recommended
If the existing toilet does not have a supply shut-off
valve below the tank, install one before installing the new
toilet.
"
NOTICE:
·
·
·
·
·
·
·
·
·
·
·
254mm
305mm
14"(356mm)
10mm
-2-
Kohler reserves the right to change marked dimensions without prior notice.
Fig.#1
1
Unit: mm
:
Reference Value
730
730
Finished Wall
Finished Wall
730
730
475
475
276
276
370
370
394
394
12
12
140
140
350
350
805
805
586
586
242
242
190
190
200
200
390
390
305
400
C of Outlet
C of Outlet
L
L
1/2" Supply
1/2"
1/2" Supply
1/2"
Front of Bowl
Front of Bowl
K-5331T-S
K-5471T-S
1207474-T01-A

Fig.#2
2
Fig.#4
4
Fig.#6
6
Fig.#7
7
Fig.#5
5
Fig.#3
3
-3-
INSTALLATION
1Position the template on the floor to ensure the template
against the wall.
Tape in place and drill holes.
3Position brackts as shown on the template and install.
5Remove flush valve from the base by turning counter
clockwise.
2Install the floor mounting.
4Firmly press the toilet gasket onto the toilet plastic trap
outlet. Then fix Plastic trap outlet following the template
layout and tighten the bolts (X3).
6Turn the tank up side and place the gasket to the tank.
Install the tank onto the bowl.
3/8"
Anchor
1/2" Supply
1/2"
190
200
Plastic Trap Outlet
Toilet Gasket
2
1
1207474-T01-A

-4-
Fig.#8
8
Fig.#10
10
Fig.#12
12
Fig.#9
9
Fig.#11
11
Fig.#13
13
7Tighten the nut from above.
9Connect the supply hose.
CAUTION: Turn on the water and allow water to flow
through the supply pipe to flush the system of any
debris or connecting fill valve.
8Install flush valve back to the position. Install the refill tube.
10 Apply weight evenly. Carefully insert the outlet into the
plastic trap.
12 Connect supply hose to shut-off valve.11 Install the new toilet with sleeves, screw and attach the
caps.
Water Supply
Hose
Outlet
Plastic Trap Outlet
Sleeve
Mounting hole
Screw
Cap
1/2" Supply
1/2"
1207474-T01-A

14 Adjust the flush valve cable.
CAUTION: Adjust the flush valve cable and refill tube
as shown to avoid flush valve cable obstructing the
function.
-5-
Fig.#15
15
Fig.#18
18
Fig.#17
17
Fig.#16
16
Fig.#14
14
13 Caulk silicone around base.
15 Install the push button.
16 Adjust the water level. 17 Flush several times and check for leaks. Do not
overtighten!
Caulk
Flush valve cable
Refill tube
Click the button before install
the push button.
Turn here to adjust the water level.
1207474-T01-A

-6-
SYMPTOMS
1. Poor flush.
3. The fill valve turns on/off
by itself or it runs,
allowing water to enter
the tank.
4. Long tank fill cycle.
5. Noisy tank fill cycle.
2. No flush.
RECOMMENDED ACTION
A. Adjust the tank water level to match the waterline.
B. Fully open the water supply shut-off valve.
C. Clear obstructions from the trapway, jet, or bowl rim holes.
D. Clear obstructions from the waste line.
A. Check the position of flush valve cable, Flush valve cable must not overlap the valve float sinks.
B. Check the position of flush valve cable, flush valve cable must not obstructive the phase of flush
valve pipe.
C. Clean or replace the flush valve seal if it is worn, dirty, or misaligned with the valve seat or flush
valve seat is damaged.
D. Remove the tank and tighten the flush valve nut if flush valve gasket is leaking. Do not overtighten.
If leakage continues replace the gasket.
E. Clean the fill valve seal of debris or replace the seal assembly.
F. Replace the fill valve if the valve float sinks.
G. Adjust the tank water level if it is too high.
A. Partially close the water supply shut-off valve if the water pressure to the toilet is too high. Check
the toilet performance following any such adjustment.
B. Remove dirt or obstructions from the valve head. Flush the lines.
A. Fully open the water supply shut-off valve.
B. Clean the valve inlet, valve head, or supply line. Flush the lines.
A. Make sure the push button rods are in place. Adjust as needed.
2. A.
5. A.
B.
4. A.
B.
3.
/
A.
B.
C.
D. /
E.
F.
1. A.
B.
C.
D.
1207474-T01-A

-7-
()
0C
o
CONSUMER RESPONSIBILITIES
If you live in a hard water area, make certain that the holes in
the toilet rim are kept clean to ensure proper bowl flushing.
Toilet bowl cleaners should be used at least once a week.
Use a long-handled brush to clean the rim holes, and to clean
as far into the trap as possible to prevent mineral deposits
from forming.
Most toilet bowl cleaners are not harmful to the vitreous china
surface of the toilet bowl. Please follow the bowl cleaner
manufacturer's instructions carefully.
Do not use abrasive cleaners or solvents.
Do not use in-tank cleaners. Products containing
chlorine (calcium hypochlorite) can seriously damage
fittings in the tank. This damage can cause leakage
and property damage.
Kohler Company shall not be responsible or liable for any
damage to these tank fittings caused by the use of cleaners
containing chlorine (calcium hypochlorite).
WARNING: Risk of property or product damage.
'
Please do not use hard materials (like
scouring pad) to clean product surface, especially the
product logo.
CAUTION:
CAUTION: Don t use any cement while installing
the toilet.
WARNING: Risk of product damage.
Heat expansion of the toilet may damage
the feet of the toilet. Kohler will not be responsible for
any damage because of using cement.
Do not throw into the toilet what is easy to block it,
such as newspaper, paper pilch, sanitary towel.
Do not bump the vitreous china with great force to
prevent it from damaging and leaking.
Do not use the product in the water below 0 C.
o
1207474-T01-A