Kohler GABRIELLE CLASS FIVE S-EB K-3322T-W User manual

GABRIELLE CLASS FIVE
TM
INSTALLATION INSTRUCTIONS
VITREOUS CHINA SIPHON JET TOILET
S-EB K-3322T-W/K-3322T-SW/K-3322T-CW
·
·
·
Please read these instructions carefully to familiarize
yourself with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
All information in these instructions is based upon the
latest product information available at the time of
publication. Kohler China reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning, and
warranty information -
.
please leave instructions for the
consumer
·
·
·-
ORDERING INFORMATION
GABRIELLE CLASS FIVE Toilet K-3322T-W
Includes French Curve Toilet Seat K-4653T
GABRIELLE CLASS FIVE Toilet K-3322T-SW
Includes CACHET Quiet-Close Toilet Seat K-4636T-U
GABRIELLE CLASS FIVE Toilet K-3322T-CW
Includes French Curve Quiet-Close Toilet Seat K-4713T
TM
TM
TM
TM
®
®
NOTES
·
·
·
·
·
·
·
·
·
·
Observe all local plumbing and building codes.
Shut off the water supply.
Seat post holes are on 140mm (5-1/2") centers.
51mm (2") passageway.
Water depth from the rim is 127mm (6-5/8").
Ensure that the new drain has the correct roughing-in
dimension. This toilet has a 305mm (12") roughing-in
dimension. .
Closet flange must be 305mm (12") on-center from wall.
Carefully inspect the new fixture for any sign of damage.
For new construction, refer to the dimensions in
for locating the shut-off valve.
Fixture dimensions are nominal and conform to tolerances
established by ASME Standards (A112.19.2-2008).
See Fig. #1
Fig. #1
and Fig. #4
·
·
·
·
·
·
·
·
·
·
140mm
51mm
127mm
305mm
1
305mm
14
ASME A112.19.2-
2008.
K-3322T-W
K-4653T
K-3322T-SW
K-4636T-U
K-3322T-CW
K-4713T
, 2011
Copyright Kohler China Ltd., 2011
528137
-1-
1176009-T01-A

-2-
TOOLS AND MATERIALS REQUIRED
(Not supplied)
·
·
·
·
·
·
·
·
·
·
·
·
·
254mm (10") adjustable wrench
305mm (12") pipe wrench
Metal file (file cut)
Tape measure
Tubing cutter
Level
Hacksaw
Putty knife
Screwdriver
Toilet gasket (wax seal)
Toilet installation flange
Toilet T-bolts (2), 8mm (5/16") diameter with nuts &
washers
Toilet supply shut-off valve
If the existing toilet does not have a supply shut-off
valve below the tank, install one before installing the new
toilet.
NOTICE:
()
·
·
·
·
·
·
·
·
·
·
·
·
·
254mm
305mm
()
8mm T (2 )
127
10mmN.P.S. SUPPLY 130
FRONT OF BOWL
390
259
248
Fig.#1
1
Unit: mm
:
Reference Value
Kohler reserves the right to change marked dimensions without prior notice.
WARNING: Risk of personal injury or product
damage.
WARNING: Risk of external leakage
Handle vitreous china products very carefully.
Vitreous china can break and chip if you over tighten
bolts and nuts.
. The fill valve
nut has been factory-tightened to design specifications.
If re-tightening is required, wrench tighten 1/4 turn past
finger tight .
1/4
681
479
718
390
FINISHED WALL
70
OF OUTLET
C
L
305
1176009-T01-A

Remove the old gasket from the floor
and the closet flange with a putty knife.
Remove the old T-bolts and discard
them.
f the new toilet is not
installed immediately, temporarily stuff
a rag into the closet flange.
NOTICE: I
T
Fig.#2
2
Closet Flange
TO REMOVE EXISTING TOILET
Turn off the water supply. Flush the toilet, and use a sponge
to remove the remaining water from the tank and bowl.
Disconnect the supply shut-off valve (if present), and remove
the old tank and bowl.
()
INSTALLATION
TO INSTALL SUPPLY
SHUT-OFF VALVE
Install the supply shut-off valve so it
is127mm above the finished floor line,
and 130mm to the left of the closet
flange centerline.
The centerline of the supply shut-off
valve outlet should extend 70mm from
the finished wall. Install the supply
shut-off valve with the outlet vertical.
127mm
130mm
70mm
Fig.#4
4
Supply Shut-Off Valve
Closet Flange
Centerline
130
305
127
Install two new 8mm (5/16") diameter
T-bolts into the closet flange.
Do not use white cement or
high lime content cements to install
this toilet. The expansion of cement
due to a rise in temperature may make
the toilet crack or cause damage.
Kohler is not responsible for any
damage caused by installation with the
use of cement.
NOTICE:
8mm T
Fig.#3
3
Closet Flange
T-bolts
T
-3-
1176009-T01-A

TO INSTALL TOILET
Set the toilet upside down on some
padding. Firmly press the toilet gasket
onto the toilet outlet.
Wax ring type toilet gasket
should not be installed at temperatures
less than 21 .
if you are using a toilet
gasket with an integral plastic sleeve,
make sure the gasket is positioned
with the sleeve facing away from the
toilet.
If you temporarily plugged the closet
flange with a rag, remove the rag at
this time and ensure that the drain pipe
is clear and free of debris.
Carefully align and lower the toilet over
the closet flange and T-bolts. Apply full
body weight to the toilet rim to set the
seal.
Do not lift or rock the
toilet after placement-anew
toilet gasket must be installed if
you break the watertight seal.
NOTE 1:
NOTE 2:
CAUTION: Risk of concealed
leakage.
1
21
2
Fig.#5
5
Toilet Outlet (OUTLET)
Toilet Gasket
Fig.#6
6
Assemble the bolt cap bases, washer,
and nuts on the exposed T-bolts.
Handtighten the nuts, then tighten
them an additional 1/2-turn.
overtightening may cause
breakage or chipping of the
vitreous china.
If the T-bolts extend more than 6mm
(1/4") over the top of the nuts, cut off
the excess and file the end. Wipe
away any residue. Install the bolt caps.
CAUTION: Risk of personal
injury or product damage.
T
T 6mm
*Supplied with toilet
*
T-Bolt
T
Bolt Cap*
*
Nut
Washer
Bolt Cap Base*
*
Supply Shank*
*
Supply Shut-Off Valve
Fig.#7
7
*()
()
TO CONNECT WATER
SUPPLY
* Flexible hose (not provided) are
recommended to connect the supply
line to the fill valve. If you use a rigid
connection(not provided), take care
not to apply side forces to the bottom
of the fill valve. Be sure the rigid
connection must be fit with supply line
completely to prevent damage shank
by forced connection.
-4-
1176009-T01-A

Attach the toilet seat according to the
installation instructions included.
Open the supply shut-off valve and
check all connections for leakage. If
the connections have been properly
assembled, a slight retightening of the
nuts should stop any leakage.
FILL FLOAT WITH
BALLAST
Test flush the toilet.
Periodically Check all connections for
leaks for several days following
installation.
Set the tank cover in place on the tank.
Fig.#9
9
Fig.#8
8
Check
This Area
-5-
OPEN
MINOR ADJUSTMENT OF
WATER LEVEL
Move the snap along "OPEN" direction.
To lower water level: Move water cup
down to a proper height and rotate
screw anticlockwise to achieve the
desired water level. (Refer to float
adjustment instructions.)
Fig.#10a
10a
Fig.#10b
10b
Snap
SCALE
5:1
Screw
OPEN
CLOSE
1176009-T01-A

To elevate water level: Rotate screw
clockwise and raise float to the desired
water level. Elevate water cup to a
proper position as well. (Refer to float
adjustment instructions.)
Fig.#10c
10c
CLOSEFasten the snap along "CLOSE"
direction.
Fig.#10d
10d
SCALE
5:1
OPEN
CLOSE
E G 2-4mm
Float adjustment instructions: Make
sure the height of surface E is 2-4mm
lower than surface G.
Fig.#10e
10e
Screw
E
Float
Water Cup G
-6-
1176009-T01-A

7. Toilet does not activate. A. Chain is not connected to lift rod or
flush valve.
A. Reconnect the chain.
1. Float valve turns on/off by itself
without toilet being flushed.
A. No slack in flapper chain assembly,
holding flapper off seat.
B. Flush valve flapper ball worn, dirty
or misaligned with flush valve seat;
or seat corroded so flapper will not
seal.
C. Refill tube pushed too far down in
overflow pipe.
A. Adjust flapper chain assembly for
proper slack.
B. Inspect, clean and, if necessary,
replace flapper ball and/or seat.
C. Attach refill to overflow pipe above
the water line.
2. Float valve continues to run, allowing
water to enter tank.
A. Foreign particles lodged under the
float valve seal (located under float
valve cap)
B. Float valve seal (located under float
valve cap) may be cracked or split.
C. Tank water level set above overflow
level.
D. Water leaking past flush ball.
A. Shut off water supply; remove float
valve cap assembly by rotating 1/8
turn counterclockwise. Cover
uncapped lower valve unit with an
inverted cup (holding it to
overspray), and turn water on and off
a few times. Clean float valve seal
surface (located under float valve cap).
Replace float valve cap assembly by
engaging lugs and rotating 1/8 turn
clockwise. Turn water on.
Install filter in supply line to prevent
recurring problems.
B. Replace seal.
C.
D. Replace flush ball.
E. Turn trip lever nut clockwise to loosen
until trip lever no longer binds
E. Trip lever binding, holding flush ball
open.
During fill cycle, hold float under water
a few seconds to allow it to fill with
water ballast. Refer to "Minor
Adjustment of Water Level" for
waterline adjustment.
prevern
3. Incorrect water level height. A. Valve float cup does not contain
enough water to provide required
ballast.
B. Float height incorrect.
A. During fill cycle, hold float under water
a few seconds to allow it to fill with
water ballast.
B. Refer to "Minor Adjustment of Water
Level" for waterline adjustment.
4. Long or noisy tank fill cycle. A. Plugged valve inlet or supply line. A. Perform Corrective Action 2.A.
5. Poor flush. A. Water level is too low.
B. Trapway or rim holes are obstructed.
C. Soil pipe or vent is obstructed.
D. Supply shut-off valve not fully open.
E. Low water level in bowl due to refill
tube being plugged or out of overflow
tube.
A. Adjust water level.
B. Unclog trapway; clean rim holes.
C. Clear obstruction from soil pipe or
vent.
D. Open supply shut-off valve.
E. Clean or straighten refill tube attach
refill tube to overflow tube.
tank
6. Toilet overflows. A. Toilet trapway is obstructed.
B. Soil pipe or vent is obstructed.
A. Use plunger to unclog.
B. Clear obstruction from soil pipe or
vent pipe.
-7-
1176009-T01-A

-8-
3. A.
B.
A.
B.
6. A.
B.
A.
B.
7. A. A.
5. A.
B.
C.
D.
E.
A.
B.
C.
D.
E.
1.
/
A.
B.
C.
A.
B.
/
C.
2. A. (
)
B. ( )
C.
D.
E.
A.
1/8
()
(
) 1/8
B.
D.
E.
C.
4. A. A. 2A
1176009-T01-A

CONSUMER RESPONSIBILITIES
If you live in a hard water area, make certain that the holes in
the toilet rim are kept clean to ensure proper bowl flushing.
Toilet bowl cleaners should be used at least once a week.
Use a long-handled brush to clean the rim holes, and to clean
as far into the trap as possible to prevent mineral deposits
from forming.
Some toilet cleaner will damage chrome surface or faucet
settings. Please use with care avoid contact with chrome
surface.
Do not use abrasive cleaners or solvents.
Do not use in-tank cleaners. Products containing
chlorine (calcium hypochlorite) can seriously damage
fittings in the tank. This damage can cause leakage
and property damage.
Kohler Company shall not be responsible or liable for any
damage to these tank fittings caused by the use of cleaners
containing chlorine (calcium hypochlorite).
WARNING: Risk of property or product damage.
'
Please do not use hard materials (like
scouring pad) to clean product surface, especially the
product logo.
CAUTION:
CAUTION: Don t use any cement while installing
the toilet.
WARNING: Risk of product damage.
Heat expansion of the toilet may damage
the feet of the toilet. Kohler will not be responsible for
any damage because of using cement.
Do not throw into the toilet what is easy to block it,
such as newspaper, paper pilch, sanitary towel.
Do not bump the vitreous china with great force to
prevent it from damaging and leaking.
Do not use the product in the water below 0 C.
o
( )()
()
()
0C
o
-9-
1176009-T01-A