Kokido Telsa 90 User manual

RECHARGEABLE POOL VACUUM
USER MANUAL
ASPIRATEUR RECHARGEABLE SANS FIL
MANUEL D’UTILISATION
HERLAADBARE BODEMZUIGER
HANDLEIDING
WIEDERAUFLADBARER POOLSAUGER
BEDIENUNGSANLEITUNG

1
Table Of Contents
SAFETY WARNINGS & INSTRUCTIONS P.5
HOW THE POOL VACUUM WORKS P.8
GETTING STARTED P.9
Charging The Battery P.9
Set-Up Before Use P.10
Side extension assembly P.10
Side extension disassembly P.11
Handle/Telescopic pole connector assembly P.11
Filter bag assembly P.11
Pool Preparation P.12
OPERATION P.12
EMPTYING THE FILTER BAG P.14
MAINTENANCE & STORAGE P.14
BATTERY DISPOSAL P.14
How to remove the battery pack P.15
TROUBLESHOOTING P.16
Remark: Product/parts photos/drawings in this manual are for demonstration only.
Product/parts in photos/drawings may vary with the model purchased.

2
Table des matières
AVERTISSEMENTS DE SÉCURITÉ ET
INSTRUCTIONS P.17
FONCTIONNEMENT DE L'ASPIRATEUR DE
PISCINE P.20
DÉBUT DES OPÉRATIONS P.21
Chargement de la batterie P.21
Réglage avant l’utilisation P.22
Assemblage des extensions latérales P.22
Démontage des extensions latérales P.23
Assemblage de la poignée / connecteur pour
manche télescopique P.23
Fixation du sac de filtration P.23
Préparation de la piscine P.24
FONCTIONNEMENT P.24
VIDER LE SAC DE FILTRATION P.26
MAINTENANCE ET STOCKAGE P.26
ÉLIMINATION DES BATTERIES P.27
Comment retirer le bloc de batteries P.27
REPÉRAGE DE PANNES P.28
Remarque: Les photos / dessins de produits / pièces de ce manuel sont uniquement
à titre de démonstration. Le produit / les pièces dans les photos / dessins peuvent
varier en fonction du modèle acheté

3
Inhoudsopgave
VEILIGHEIDSWAARSCHUWINGEN &
INSTRUCTIES
P.29
HOE DE ZWEMBADSTOFZUIGER WERKT P.32
VAN START GAAN P.33
Batterij opladen P.33
Instellen voor gebruik P.34
Extensie monteren P.34
Extensie demonteren P.35
Handgreep/Telescopische paalverbinding
monteren P.35
Filterzak monteren P.35
Voorbereiding Zwembad P.36
GEBRUIK P.36
FILTERZAK LEGEN P.38
ONDERHOUD & OPSLAG P.38
VERWIJDERING VAN DE BATTERIJ P.39
Hoe de batterij verwijderen P.39
PROBLEMEN OPLOSSEN P.40
Opmerking: Foto's/tekeningen van (onderdelen van) het product in deze handleiding
dienen alleen ter illustratie. Foto's/tekeningen van (onderdelen van) het product
kunnen verschillen van het model dat u hebt aangeschaft.

4
Inhaltsverzeichnis
SICHERHEITSHINWEISE UND
ANWEISUNGEN S.41
WIE DAS POOL-VAKUUM FUNKTIONIERT S.44
FERTIG MACHEN S.45
Die Batterie aufladen S.45
Vor Gebrauch einrichten S.46
Verlängerung montieren S.46
Verlängerung demontieren S.47
Griff/Teleskopstangenverbinder montieren S.47
Filterbeutel montieren S.47
Poolvorbereitung S.48
BETRIEB S.48
LEEREN DER FILTERTASCHE S.50
WARTUNG & LAGERUNG S.50
BATTERIE ENTSORGUNG S.51
So entfernen Sie den Akku S.51
FEHLERBEHEBUNG S.52
Kommentare Produkte/Teile auf den Fotos/Zeichnungen in dieser Anleitung dienen
nur zur Veranschaulichung. Produkte/Teile auf den Fotos/Zeichnungen können beim
gekauften Artikel variieren.

5
SAFETY WARNINGS & INSTRUCTIONS
Read and follow all instructions in this manual and on the equipment. Failure to do so
could result in severe or fatal injuries.
SAVE THESE INSTRUCTIONS
WARNING!
-This is not a TOY. Children should be kept out of reach from this pool
vacuum and its accessories.
-Never allow children to operate this product.
-This pool vacuum is not intended for use by someone with reduced
physical, sensory or mental capabilities, and/or a lack of experience and
knowledge unless they have been given instructions concerning the
appliance and are under supervision of the person responsible for their
safety.
-Children must not play with this product
-Cleaning and user maintenance must not be carried out by children
-Make sure the pool vacuum is fully immersed in water before initiating
operation. The minimum water level required to operate the pool vacuum
must cover the entire pool vacuum. Operating the pool vacuum when it is
not immersed in the water correctly could damage the unit and void the
warranty as a result.
-Maximum operating depth in water is 3 meters (10 ft.).
-Operating water temperature: 5˚C(41˚F) –35˚C(95˚F)
-Only use the detachable supply unit (external adaptor) provided with this
pool vacuum to charge the battery.
-Detachable supply unit (external adaptor)
-Connect the external adaptor to a power source through a residential
current device (RCD) / a ground fault circuit interrupter (GFCI). If in doubt,
consult a qualified professional electrician.
-Do not use this pool vacuum if any damage is detected.
-Replace damaged parts as soon as possible. Only use parts certified by
the distributor or manufacturer.
-Turn off the pool vacuum, disconnect the external adaptor from the power
source, and unplug it from the charging plug, before detaching the
charging plug from the pool vacuum.
-Disconnect the pool vacuum from the supply mains and make sure the
pool vacuum is powered OFF prior to servicing it such as cleaning the filter
bag.
-The battery installed is a rechargeable Li-ion battery pack. Never attempt
to replace it.
-The pool vacuum is only to be recharged with external adaptor and
charging plug delivered with this product.
-DO NOT handle the pool vacuum, external adaptor and charging plug
while it is charging with wet limbs and without shoes.

6
-You should not operate this pool vacuum when people/pets are present in
the water.
- DO NOT use this pool vacuum without an intact filter bag in place,
otherwise your warranty will be voided as a result.
-Suction entrapment hazard: This pool vacuum generates suction. Do not
allow hair, body, and any loose parts of your clothing to make contact with
the suction point of the pool vacuum during its operation.
-Never insert body parts, clothing, and other objects into the openings and
moving parts of the pool vacuum.
-DO NOT use this pool vacuum to pick up any toxic substance, flammable,
and combustible liquids such as gasoline, and in the presence of explosive
or flammable fumes.
-Under no circumstances should you attempt to disassemble the pool
vacuum and replace the impeller, motor, and battery by yourself.
-Never insert fingers and any object to touch the impeller.
-This pool vacuum shall not be used by children.
-The battery must be removed from the pool vacuum by an expert before
it is scrapped.
-The pool vacuum must be disconnected from the supply mains as the
battery is removed.
-For detail regarding battery disposal, refer to the section "Battery Disposal”
in this manual
-The battery must be disposed safely in accordance with local ordinances
or regulations.
-The pool vacuum contains a maintenance-free, rechargeable lithium-ion
battery pack, which must be disposed properly. Recycling is required;
please contact your local authorities for more information.
- External adaptor and charging plug:
Never use the external adaptor and charging plug for anything
other than charging the battery of the pool vacuum that is supplied
in the same pack.
The external adaptor and charging plug should not be used outdoors,
nor should it be exposed to rain, humidity, any liquid or heat.
The transformer ( or external adaptor) is to be located outside zone
1
Keep the external adaptor and charging plug out of reach of children.
Never use the external adaptor and charging plug if any damage is
detected.
DO NOT handle the external adaptor and charging plug with wet
hands.
Keep the external adaptor disconnected from power when it is not in
use.
Never attempt to dissect the external adaptor.

7
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent, or an equally-qualified person in
order to prevent hazards of any kind.
Make sure the pool vacuum is completely dry before charging.
CAUTION!
-This pool vacuum is designed for underwater use only; it is not an all-purpose
vacuum cleaner. DO NOT attempt to use it to clean anything other than your pool.
-Use only original accessories delivered with this product.
-DO NOT use this pool vacuum right after pool-shocking. It is recommended to first
leave the pool circulating for at least 24-48 hours.
-If you are planning on using the pool vacuum in a saltwater pool, make sure all salt
are dissolved before placing it in the water.
-It is not recommended to use this pool vacuum with another cleaner simultaneously.
-Avoid picking up hard, sharp objects with this product as they may damage the pool
vacuum and filter.
-To avoid damaging the external adaptor and charging plug, do not attempt to carry
the pool vacuum by the cable of external adaptor or pull the cable in hopes of
disconnecting it from the power source and charging plug.
-Charge the pool vacuum indoors in a clean, dry area with good ventilation and
away from sunlight.
-DO NOT leave the pool vacuum charged for over 10 hours.
-If the pool vacuum will not be used for an extended period, detach it from the
charging plug and use a damp cloth to clean and dry the pool vacuum and its
accessories. Make sure to charge the pool vacuum to about 30% to 50% of the
battery capacity before it is stored. Store in a well-ventilated area away from
sunlight, heat, ignition sources, pool chemicals, and children. Recharge the pool
vacuum every three months.
-All actions concerning the disassembly of the main unit (i.e. battery disposal) can
only be carried by an authorized technician.
Above warnings and cautions are not intended to incorporate all possible
instances for risks and / or severe injuries. Pool / spa owners should always
exercise extra caution and common sense when utilizing the product.

8
HOW THE POOL VACUUM WORKS
Replacement
Number
Replacement
Number
1. Main unit EV90ASM04 5. Regular Filter bag
x 1
EV90-06-001
1.1 Charging port (with 2
charging pins for
charging)
------------- 5.1 Fine Filter bag (for
filtering fine
particles) x 1
EV90-06-002
1.2 Water sensors --------------
2. Handle / Telescopic
pole connector (
with
connector and spring)
EV90ASM01 6. Wheel x 3 EV90ASM03
3. Left extension EV90ASM02 7. Charging plug EV90-09
4. Right extension 8. Adaptor EV90-08-002 (for
EU only)

9
GETTING STARTED
Charging The Battery
IMPORTANT NOTE: Fully charge the pool vacuum (about 5-6 hrs) before using it
for the first time.
WARNING!
Use only the original external adaptor and charging plug provided.
Make sure the pool vacuum and the charging port are clean and dry before set-
up.
1.
2. Connect the external adaptor to the power source. The indicator light on the
external adaptor will turn red when the vacuum is charging and green when it is
fully charged. Charge it for 6 hours for best performance.
Place the unit on a flat surface. Set the pool vacuum to Power Off/ Charging
Mode by turning the switching knob anticlockwise until it clicks and completely
exposes the charging port.
Align and attach the charging plug to the charging port.
WARNING!
Be sure
not to invert the charging plug and ensure both the charging plug and charging
port are clean and dry before charging them. TIPS: Use cotton bud to dry
the chaging port and pins.
Plug the charging cable of the external adaptor into the charging plug.
RED light - Charging
GREEN light - Charged

10
 Immediately disconnect the external adaptor from the power source if you
detect any of the following:
-Offensive or unusual odor
-Excessive heat
-Deformation, cracks, leaks
-Smoke
3. When charging is complete, disconnect the external adaptor from the power
source and unplug the charging cable from the charging plug. Detach the
charging plug from the main unit. WARNING! Never leave the charging plug
while the pool vacuum is in the water.
Normally the pool vacuum is designed to operate for up to 75 minutes on a full
charge.
Note: Empty the filter bag regularly. Excessive debris increases the burden to the
motor and may shorten the operating time.
NOTE: Rechargeable lithium-ion battery is classified as a consumable item. It has
a limited life and will gradually lose its capacity to hold a charge. Therefore, the
running time of the pool vacuum will gradually reduce after repeated charging and
discharging throughout its product life.
Once the lifespan of the battery reaches its end, refer to section “BATTERY
DISPOSAL” for instructions regarding battery disposal.
NOTE: Let the pool vacuum rest for around 30 to 40 minutes before charging it
again.
Set-Up Before Use
This pool vacuum has removable extensions which can be removed to clean the
narrow areas.
Side extension assembly
Insert the stem of the wing to the hole on the side of the main body. Turn the wing and
press on it to secure it to the main body. You will hear a “click” sound.

11
Side extension disassembly
Reverse the steps to disassemble the extension from the main unit.
Handle/Telescopic pole connector assembly
Align and insert the handle/ pole connector into the post as shown. Slide the telescopic
pole into the pole connector until the holes on the side of the telescopic pole are
secured to the pins of the pole connector.
Filter bag assembly
Note: if the pool is too dirty with fine sand and mud, use fine filter bag.
Spread the filter bag over the top opening of the main body
of the pool vacuum. Make sure the cord of the bag is placed
under the flange of the top opening.

12
While holding the cord, press on the cord fastener and push
it under the flange.
TIPS: To secure the filter bag, when pushing the cord
fastener under the flange, pull one cord instead of two cords
as shown in diagram
Lift up the bag to ensure it is totally secured before deploying
the pool vacuum into water.
Pool Preparation
- If the liner is brittle, damaged, or wrinkled, contact a qualified professional to perform
the necessary repairs or perform a liner replacement prior to using the pool vacuum .
- If you are using a saltwater pool, make sure all salt are dissolved before placing the
pool vacuum into the water.
OPERATION
1) Bring your pool vacuum to the side of your pool. Turn the switching knob clockwise
until it clicks to expose the water sensors. The light at the top will turn blue.
Immerse the pool vacuum into water, the light turns immediately to green and the
impeller will start to turn after 4-5 seconds.

13
To effectively vacuum up debris, ensure the pool vacuum is laid flat on the pool floor
as you steer it back and forth in regular motion over debris patches for collection.
Debris is collected from the front, side and back to fill up the filter bag.
Excess dirt and debris in the pool could clog the impeller, which would automatically
stop to protect the motor, and the indicator light would turn red. Remove the vacuum
from the pool and turn it off prior to unclogging and emptying the filter bag if it is full.
To resume operation, turn the switching knob anticlockwise until Power Off is selected,
then turn it clockwise to select Power On.
2) To retrieve the pool vacuum, bring it poolside and flip it upside down before lifting.
This is done to prevent debris from scattering back into the pool (especially if you
are using the fine filter bag) and avoid bending the pole in the process.
Once the pool vacuum is out of the water, the impeller will cease to spin within 2-3
seconds. The LED light will turn blue. When battery level is running low, blue light will
flash.
3) Rinse the pool vacuum with fresh water after every use. DO NOT use any
aggressive detergent.
4) Dry the charging port and pins thoroughly (TIPS: Use cotton bud to dry them)
Light Color
Blue Power On
(ready for operation)
Blue – Flash Battery level is running low
Green In operation
Green -Flash Battery level is running low.
Green light
Off
Battery depleted
(need to be recharged)
Red Impeller stops
(impeller clogged).

14
EMPTYING THE FILTER BAG
CAUTION! Make sure the pool vacuum is OFF before cleaning the filter bag.
Place the cleaner on a flat surface. Press on the cord fastener to release the bag from the
main body. It is recommended to clean the filter bag with splashing water. If brushing is
deemed necessary, use only a soft brush to clean it carefully and gently to avoid any
damages.
MAINTENANCE & STORAGE
NOTE:
1. Battery discharges on its own during storage. Make sure to charge the pool vacuum
to about 30% to 50% of the battery capacity before it is stored.
2. You must recharge the battery at least once every three months when it is not in use.
Unplug the external adaptor from the socket and the charging cable from the charging
plug.
Detach accessories from the pool vacuum. If necessary, rinse the pool vacuum and
accessories with fresh water. DO NOT use aggressive detergent.
Be sure to dry the pool vacuum before storage.
Use a damp cloth to clean and dry the pool vacuum and its accessories.
Store them in a well-ventilated area away from sunlight, heat, ignition sources, pool
chemicals, and from children. Ambient temperature for storage should be 10˚C – 25˚C
(50˚F – 77˚F). NOTE: A higher storage temperature may reduce the battery life.
WARNING!
-Under no circumstances should you attempt to disassemble the main unit and
replace the impeller, motor, and battery by yourself.
CAUTION!
Excessive heat can damage the battery and reduce the lifespan of your pool vacuum
as a result.
Consult your dealer regarding battery replacement if the following happens:
-Battery does not charge fully.
-Battery operation time is noticeably reduced. Observe and record the run times of
the first few operations (on a full charge). Use these run times as a reference point
for comparison with run times in the future.
The battery must be removed from the pool vacuum before it is scrapped.
The battery is to be disposed safely in accordance with local ordinances or
regulations.
NOTE: Incorrect maintenance may reduce the battery life and affect its capacity as a result.
BATTERY DISPOSAL (To be carried out by authorized technician)
Your pool vacuum is equipped with a maintenance-free rechargeable lithium-ion battery
pack, which must be disposed of properly. Recycling is required; please contact your
local authority for more information.
WARNING! Never attempt to disassemble a battery pack
Remove all personal items such as rings, bracelets, necklaces, and watches when the
battery pack is unwired from the pool vacuum.
A battery can produce a short circuit current high enough to weld a ring (or similar item)

15
to metal, causing a severe burn in the process.
Wear complete eye protection, gloves, and protective clothing when the battery pack is
being removed.
Avoid touching the wires altogether and avoid contact between them and any metal
items, which could cause sparking and/or short circuit the battery.
Never smoke or allow a spark or flame in the vicinity of the battery or the pool vacuum.
Do not expose the battery to fire or intense heat as this may result in an explosion.
CAUTION!
If a battery leak occurs, avoid any contact with the leaking fluids and place the damaged
battery in a plastic bag.
-If leaking fluids come in contact with skin and clothing, wash immediately with plenty
of soap and water.
- If leaking fluids come in contact with eyes, do not rub them and immediately flush
them with cool running water for at least 15 minutes. Seek medical attention as soon
as possible.
How to remove the battery pack
Recommended tools (not included): Screwdriver.
WARNING! The pool vacuum must be disconnected from the supply mains before
removing the battery pack.
1. Place the pool vacuum on a flat surface. Use the screwdriver to unfasten the
screws on the back cover. Remove the battery from the chamber.
2. To detach the battery connection wire, press on the clip of the connector to pull
it out. NOTE: Wrap the connector immediately with insulating tape in order to
avoid any short circuit caused by the contact of both wire terminals.

16
TROUBLESHOOTING
Problem Possible Cause Solution
Cleaner does not start working under
water (after 5-10 seconds)
Stained water sensors The stains can be removed by using a cotton bud
soaked with juice of lemon or vinegar to clean the
areas around the water sensors.
Out of battery Charge the pool vacuum
Does not capture the debris Low battery Charge the pool vacuum.
Jammed impeller Remove the pool vacuum from the water and turn the
knob anticlockwise to shut it off. Check and see if the
impeller is jammed by large debris. Remove the debris.
If necessary, contact your dealer for further
instructions.
WARNING! Make sure the pool vacuum is off
before the unit is serviced.
Broken impeller Contact your dealer for replacement.
Filter bag is full / clogged Clean the filter bag.
Charging time is longer than
advertised
Stained charging pins The stains can be removed by using a cotton bud
soaked with juice of lemon or vinegar to clean the
areas around the charging pins.
Cleaner cannot be charged Damaged battery Contact dealer for battery replacement.
WARNING! DO NOT replace the battery by
yourself. This could result in severe or fatal injuries and
the warranty will be voided as a result.
Charging plug is not correctly
connected to external adaptor
and pool vacuum.
Refer to instruction manual and connect the charging
accessories correctly.
External adaptor is out of order Contact dealer for replacement.
WARNING! Using the wrong external adaptor
will result in damaging the pool vacuum / battery and
voiding the warranty as a result.
Environmental Programmes, WEEE European Directive
Please respect the European Union regulations and help to protect the environment.
Return non-working electrical equipment to a facility appointed by your municipality that properly
recycles electrical and electronic equipment. Do not dispose them in unsorted waste bins. For items
containing removable batteries, remove batteries before disposing of the product.
If soft copy of this instruction manual is required, please contact our customer service by email:
customerserv[email protected]
SAVE THESE INSTRUCTIONS

17
AVERTISSEMENTS DE SÉCURITÉ ET
INSTRUCTIONS
Lire et suivre toutes les instructions figurant dans ce manuel et sur l’équipement. Ne
pas le faire pourrait donner lieu à des blessures graves ou mortelles.
CONSERVEZ CES INSTRUCTIONS
AVERTISSEMENT !
-Ceci n’est pas un JOUET. Cet aspirateur de piscine et ses accessoires
doivent être maintenus hors de la portée des enfants.
-Ne jamais permettre aux enfants de faire fonctionner ce produit.
-Cet aspirateur de piscine n’est pas prévu pour être utilisé par quelqu’un
avec ses capacités physiques, sensorielles ou mentales diminuées, ou un
manque d’expérience et de connaissances à moins d’avoir reçu des
instructions déterminées relatives à l’appareil et sous la supervision de la
personne responsable de leur sécurité.
-Les enfants ne doivent pas jouer avec ce produit
-Le nettoyage et l'entretien du produit ne doivent pas être effectués par des
enfants
-S’assurer que l’aspirateur de piscine est totalement immergé dans l’eau
avant de le mettre en marche. L’appareil doit être complétement immergé
dans l’eau afin de fonctionner correctement. Faire fonctionner l’aspirateur
de piscine lorsqu’il n’est pas immergé correctement dans l’eau peut
endommager l’unité et annuler de ce fait la garantie.
-La profondeur maximale de fonctionnement dans l’eau est de 3 mètres
(10 pieds).
-Température minimale et maximale de l’eau : 5°C – 35°C
-Pour charger la batterie, utilisez uniquement l'unité d'alimentation
amovible (adaptateur externe) fournie avec cet aspirateur de piscine.
-unité d'alimentation amovible (adaptateur externe)
-Brancher l’adaptateur externe à une source d’alimentation à travers un
dispositif à courant résiduel (RCD) / disjoncteur différentiel de fuite à la
terre (DDFT). En cas de doute, consulter un électricien professionnel
qualifié.
-Ne pas utiliser cet aspirateur de piscine si un dommage quelconque est
détecté.
-Remplacer les pièces endommagées le plus rapidement possible.
N’utiliser que des pièces certifiées par le distributeur ou le fabricant.
-Mettre l’aspirateur de piscine hors tension. Débrancher l’adaptateur
externe de la source d’alimentation avant de le débrancher la prise de
charge, puis retirer la prise de charge de l’aspirateur de piscine.
-Débrancher l’aspirateur de piscine de l’alimentation principale avant de
réaliser la maintenance d’utilisateur telle que le nettoyage du filtre.
-La batterie installée est un bloc de batteries rechargeables au lithium. Ne

18
jamais tenter de remplacer le bloc de batteries.
-L’aspirateur de piscine ne doit être rechargé qu’avec l’adaptateur externe
et la prise de charge livrés avec ce produit.
-NE PAS manipuler l'aspirateur de piscine, l'adaptateur externe ou la prise
de charge lors de la recharge avec des membres humides et sans
chaussures.
-Vous ne devez pas utiliser cet aspirateur de piscine lorsque des
personnes / animaux domestiques sont présents dans l'eau.
-NE PAS utiliser cet aspirateur de piscine sans un sac de filtration intact en
place, car votre garantie serait annulée de ce fait.
-Danger de piégeage de l’aspiration : Cet aspirateur de piscine produit une
aspiration. Ne pas permettre que les cheveux, le corps, ou toutes parties
lâches de vos vêtements entrent en contact avec l’orifice d’aspiration de
l’aspirateur de piscine pendant son fonctionnement.
-NE JAMAIS introduire des parties du corps, vêtements ou autres objets
dans les ouvertures et pièces mobiles de l’aspirateur de piscine.
-NE PAS utiliser cet aspirateur de piscine pour ramasser toute substance
toxique, des liquides inflammables ou combustibles tels que l’essence, ou
en présence de fumées explosives ou inflammables.
-Ne jamais tenter de démonter d’une quelconque façon cet aspirateur de
piscine afin de remplacer vous-même la turbine, le moteur ou la batterie.
-Ne jamais introduire les doigts ou un quelconque objet qui toucherait la
turbine.
-Cet aspirateur de piscine ne doit pas être utilisé par des enfants.
-La batterie doit être retirée de l'aspirateur de piscine par un professionnel
avant d'être jetée.
-Pour retirer la batterie, l'aspirateur de la piscine doit être déconnecté du
réseau d'alimentation.
-Pour plus de détails sur l’élimination de la batterie, reportez-vous à la
section « Élimination de la batterie » de ce manuel.
-La batterie doit être disposée en toute sécurité conformément aux
ordonnances ou réglementations locales.
-L'aspirateur de piscine contient une batterie rechargeable au lithium-ion
sans entretien, qui doit être correctement disposée. Le recyclage est
requis ; veuillez contacter vos autorités locales pour plus d'informations.
- Adaptateur externe et prise de charge :
Ne jamais utiliser l’adaptateur externe et la prise de charge pour tout
autre chose que le chargement de la batterie de l’aspirateur de
piscine qui est fournie dans le même bloc.
L’adaptateur externe et la prise de charge ne doivent pas être utilisés
à l’extérieur, ni exposés à la pluie, à l’humidité, à un quelconque
liquide ou à la chaleur.
Le transformateur (ou l'adaptateur externe) doit être situé en dehors
de la zone 1.
Maintenir l’adaptateur externe et la prise de charge hors de la portée
des enfants.

19
Ne jamais utiliser l’adaptateur externe et la prise de charge si un
quelconque dommage est détecté.
NE PAS manipuler l’adaptateur externe et la prise de charge avec
des mains humides.
Gardez l'adaptateur externe déconnecté de l'alimentation lorsqu'il
n'est pas cour d’utilisation.
Ne jamais tenter d’ouvrir l’adaptateur externe.
Si le cordon d’alimentation est endommagé, il doit être remplacé par
le fabricant, son agent ou une personne également qualifiée afin de
prévenir des dangers de tout type.
S’assurer que l’aspirateur de piscine est complètement sec avant de
le charger.
MISE EN GARDE !
-Cet aspirateur de piscine est uniquement conçu pour une utilisation sous l’eau ; il
ne s’agit pas d’un aspirateur tout usage. NE PAS tenter de l’utiliser pour nettoyer
tout autre chose que votre piscine.
-Utiliser uniquement les accessoires originaux livrés avec ce produit.
-Ne pas utiliser cet aspirateur de piscine juste après le nettoyage chimique de la
piscine. Il est recommandé de laisser circuler l’eau dans la piscine durant au moins
24-48 heures.
-Si vous prévoyez d'utiliser l'aspirateur dans une piscine d'eau salée, assurez-vous
que tout le sel est dissous avant de le placer dans l'eau.
-Il n’est pas recommandé d’utiliser cet aspirateur de piscine avec un autre
aspirateur de piscine simultanément.
-Éviter de ramasser des objets durs ou pointus avec ce produit. Ils peuvent
endommager l’aspirateur de piscine et le filtre.
-Pour éviter d’endommager l’adaptateur externe et la prise de charge, ne pas
transporter l’aspirateur de piscine par le câble de l’adaptateur externe et ne pas
tirer sur le câble pour le débrancher de la source d’alimentation et de la prise de
charge.
-Charger l’aspirateur de piscine à l’intérieur dans une zone propre et sèche avec
une bonne aération et à l’abris du soleil.
-NE PAS laisser l’aspirateur de piscine chargé pendant plus de 10 heures.
-Si l’aspirateur de piscine n’est pas utilisé pendant une longue période de temps,
le séparer de la prise de charge et utiliser un chiffon humide pour nettoyer et
sécher l’aspirateur de piscine et ses accessoires. S’assurer de charger l’aspirateur
de piscine à 30% - 50% de sa capacité avant de le ranger. Le ranger dans une
zone bien aérée éloignée de la lumière du soleil, de la chaleur, de sources
d’ignition, des produits chimiques pour la piscine et des enfants. Ne jamais laisser
l’aspirateur de piscine branché pour un stockage à long terme. Recharger
l’aspirateur de piscine tous les trois mois.
-Toutes les actions concernant le démontage de l'unité principale (c'est-à-dire
élimination de la batterie) ne peuvent être effectuées que par un technicien agréé.
Les avertissements et mises en garde ci-dessus ne prétendent pas inclure tous
les possibles cas de risques et / ou de blessures graves. Les propriétaires de
piscine / spas doivent toujours prendre des précautions supplémentaires et utiliser leur
bon sens lorsqu’ils utilisent le produit.