Kolpin 33-0070 User manual

© 2017 Kolpin Outdoors Inc. REV 03
ATV STORM CHASER PLOW
PUSH TUBE KIT
P/N 33-0070
OWNER’S MANUAL
Application
MID-BODY A V MOUN NO. 15-XXXX, ALL MOUN NO. 15-0050
ATTENTION DEALER: CUSTOMER MUST RECEIVE A COPY OF THIS MANUAL
AT THE TIME OF SALE.
Before you begin, please read these instructions and check to be sure all parts and tools are
accounted for. hese instructions will help you to become familiar with operation of the plow push
frame. Instructions contain details required to install, service the contents of this kit, for adjustment
and maintenance.

2
© 2017 Kolpin Outdoors Inc. REV 03
INTRODUCTION
Congratulations! You’ve just purchased one of the industry’s top plow system component. he Kolpin Plow Push Frame works great for
all types of plowing. With proper care and maintenance, your plow push frame will last for many years!
he blade pivot design allows the operator to select multiple angled left-or-right positions, and also incorporates a spring-loaded ’trip’
system that allows the blade to handle impacts with small obstructions. Additionally, this plow frame will handle light to medium-duty
summer landscape work.
NOTICE
Plo operation requires
additional components for operation:
High Rise Blade, Winch Kit or Manual Lift Kit,
Mid-Body ATV Plow Mount *
*These components may be specific to your vehicle.
Please read and understand all adjustment/maintenance instructions, notices and warnings before assembling and operating your
plow system.
Follo these guidelines to ensure satisfactory operation:
• Read this manual and your A V operators manual before use.
• Periodically check for wear and tightness of all fasteners. Replace or re-torque fasteners as necessary.
• Before first use, set plow in the furthest right or left angled position to check for clearance between the plow and front tires.
• Operate with extreme caution on slopes and rough terrain. Be familiar with the area before you plow.
• Be aware of immovable objects that could be hidden in the area you are plowing.
• o avoid damage when pushing snow into a pile, reverse direction before raising the plow blade.
• Do not ram the plow blade into piles of snow. **Slow down before hitting a pile.**
• For best results, set the suspension preload of your A V to the stiffest setting.
• o reduce steering effort and increase mobility, set the air pressure of your tires to the maximum pressure specification.
• he plow skids are adjustable. General skid setting is even with the plow wear bar bottom edge, higher settings reduce the
chance of rocks and gravel from being collected.
• o increase traction during plow operation, operators can try: Securing weight to the A V for additional tire downforce, reducing
tire air pressure, or installing tire chains.
• he plow blade assembly is designed to ‘trip’ when it strikes an object or digs in too far. When pressure is released, the plow
springs back into position. Spring tension can be increased by tightening the locknuts on the bottom of the eyebolts. For less
spring tension, loosen the locknuts.
• Always wear appropriate protective clothing as recommended in A V’s operator’s manual.
• Keep away from blade and moving parts during operation.
• Keep these instructions for future reference.
• All directions referring to right and left are when the rider is sitting on the machine.
• Your Kolpin accessory is exclusively designed for your vehicle.

3
© 2017 Kolpin Outdoors Inc. REV 03
DANGER
TO AVOID SERIOUS INJURY OR DEATH:
1. DO NOT EXCEED 5 MPH (8 KM/H) WITH THE BLADE INSTALLED.
2. OPERATE WITH EXTREME CAUTION ON SLOPES, STEEP GRADES, AND ROUGH TERRAIN.
3. ALLOW NO RIDERS ON BLADE OR ATV WHILE MOVING OR STATIONARY.
4. KEEP BYSTANDERS AWAY FROM THE BLADE OR ATV WHILE MOVING OR STATIONARY.
5. WHEN PUSHING HEAVY MATERIAL, DIRECTION CONTROL MAY BECOME DIFFICULT.
6. BEFORE ADJUSTING BLADE: STOP ATV ENGINE; SET AND LOCK BRAKES; RAISE AND LOCK
BLADE IN UP POSITION. DO NOT ATTEMPT TO RAISE BLADE BY HAND; USE THE LIFT
MECHANISM ONLY.
7. LOWER BLADE TO DOWN POSITION WHEN BLADE AND ATV ARE NOT IN USE.
8. READ PUSH FRAME'S INSTRUCTION SHEETS AND ATV OWNER MANUAL.
!!
SAFETY INFORMATION
Our plow systems were designed with your safety in mind. Please read and understand all Cautions, Notices and Warnings in this
manual before you begin. In order to protect you and your A V, certain parts of the plow system and/or hardware are designed to fail
when the equipment is over-stressed.
BEFORE YOU BEGIN:
• Your Kolpin accessory is exclusively designed for
your vehicle.
• Please read and understand all instructions.
• Verify all parts and tools are accounted for.
• To ensure a satisfactory installation, follo all
steps correctly and in the sequence described.
• Keep these instructions for future reference or for
informational requests.
• To facilitate installation, make sure that your
vehicle is clean and free of debris.
• All directions referring to right and left are hen
the rider is sitting on the machine
TOOLS REQUIRED:
• 13mm rench or 13mm socket
• 15mm rench or 15mm socket
• 17mm rench and 17mm socket
• 19mm rench and 19mm socket
• 21mm rench or 21mm socket
• 22mm rench or 22mm socket
• Long nose pliers or spring puller or shoe-
string sized rope
APPROXIMATE ASSEMBLY TIME: 15 minutes
Note: The Kolpin Plo Push Frame kit comes mostly assembled from factory. Some assembly is required.
RE-TORQUE ALL BOLTS AND NUTS AFTER THE FIRST 30 MINUTES OF USE.

4
© 2017 Kolpin Outdoors Inc. REV 03
Kit Contents:
Item Qty Part Description Part Number
11Push Frame Welded Assembly -
21Blade Hinge Pivot Frame -
31Pivot Lock Lever 33-0070-CP04-B
41Pivot Lock Lever Bracket 33-0070-CP03
52Blade rip Spring 33-1409
62Eye Bolt, Zinc Plated, Full hread, M8-1.25 x 110mm PUR1216
72Blade Stopper Plate CYC0813
81Lever ension Spring PUR1437
92Hex Nylon Lock Nut, Zinc Plated, M8-1.25 -
10 2Hex Nylon Lock Nut, Zinc Plated, M12-1.75 -
11 4Hex Nylon Lock Nut, Zinc Plated, M10-1.5 -
12 1Hex Nylon Lock Nut, Zinc Plated, M14-2.0 -
13 1Hex Bolt, Zinc Plated, M10-1.5 x 50mm -
14 1Large bushing, Ø11mm ID x Ø25 mm OD x 14mm LG -
15 4Flat washer, Zinc Plated, M10 -
16 1Small bushing, Ø11mm ID x Ø25 mm OD x 8mm LG -
17 3Hex Bolt, Zinc Plated, M10-1.5 x 35mm -
18 2Hex Bolt, Zinc Plated, M12-1.75 x 40mm -
19 1Spring Loop Washer Plate -
20 1Hex Bolt, Zinc Plated, M14-2.0 x 50mm -
21 1Kolpin Decal -
22 1Owner’s Manual (not shown) -

5
© 2017 Kolpin Outdoors Inc. REV 03
Kit Contents (continued):

6
© 2017 Kolpin Outdoors Inc. REV 03
ASSEMBLY INSTRUCTIONS:
PIVOT LOCK LEVER
INSTALLATION:
1. Position the pivot lever, item #3, into
the pivot lock bracket, item #4. Insert
the M10 bolt, item #13, and M10
washer, item #15, thru the bracket as
shown. hen slide bushing, item #14,
onto bolt threads and follow with lever.
Fasten with M10 washer and M10 lock
nut, item #4. ighten nut, then back out
1/8 - 1/4 turn to allow lever to pivot
freely. he pivot lever assembly is
ready to be mounted on push frame.
(See illustration 1-1) Note the lever
must pivot freely.
2. Position blade hinge pivot frame, item
#2, and pivot lever assembly onto push
frame, item #1, as shown. Insert M14
bolt, item #20, and spring loop washer
plate, item #19, thru pivot lever
assembly - blade hinge frame - push
frame. Fasten with M14 nut, item #12.
ighten M14 nut, then back out 1/8 -
1/4 turn to allow blade hinge frame to
pivot freely. (See illustration 1-2)
Note, blade hinge must pivot freely.
3. Insert M10 bolt, item #17, and M10
washer, item #15, thru pivot lever
assembly - small bushing, item #16, -
push frame. Fasten with M10 washer,
item #15, and M10 nut, item #11.
ighten to specification. (See
illustration 1-2) Note the small bushing
fits in between pivot bracket and push
frame.
#13
ILL. 1-1
#3
#14
#4
#15
#15
#11
10MM FASTENER TORQUE:
34 ft-lbs. (46 N-m)
ILL. 1-2
#17
#2
#12
#20
#19
#15
#16
#1
#15
#11

7
© 2017 Kolpin Outdoors Inc. REV 03
ASSEMBLY INSTRUCTIONS
(continued):
PIVOT LOCK LEVER
INSTALLATION (continued):
3. Install lever spring, item #8, to lever
and loop washer holes as shown.
Using a rope or a spring puller allows
for easy installation of spring. (See
illustration 1-3)
PUSH FRAME INSTALLATION
ONTO BLADE ASSEMBLY:
1. Attach the assembled push frame to
the blade. Insert M12 hex bolts, item
#18, thru holes in the blade and push
frame. Fasten the push frame to the
blade using M12 hex nuts, item #10.
ighten nut, then back out 1/8 - 1/4
turn to allow blade to hinge freely.
(See illustration 2-1) Note, bolt should
be tight enough to not move, but the
blade must rotate freely.
2. Assemble blade trip springs, item #5,
and eyebolts, item #6, between the
blade assembly and the pivot spring
tab brackets. Fasten eyebolts to frame
tab with M8 hex nylon nuts, item #9,
onto the eyebolts until 2-3 threads
show thru the locking feature. (See
illustration 2-2)
#8
ILL. 1-3
ILL. 2-1
#18
#10
ILL. 2-2
#5
#9
#6

8
© 2017 Kolpin Outdoors Inc. REV 03
ASSEMBLY INSTRUCTIONS
(continued):
PUSH FRAME INSTALLATION
ONTO BLADE ASSEMBLY
(continued):
3. Install the blade stopper plates, item
#7, onto blade hinge pivot frame.
Fasten with M10 hex bolt, item #17,
and M10 hex nuts, item #11, as shown.
(See illustration 2-3) Note, do not
tighten fasteners at this time.
4. Once plow system is mounted to the
A V, adjust the blade stops and blade
trip spring tension as desired to
achieve best performance. (See
illustration 2-4)
5. ighten the blade stopper plate
fasteners to specification.
BLADE STOPPER ADJUSTMENT
ILL. 2-3
#17
#7
#11
ILL. 2-4
1
2Min
Max
10MM FASTENER TORQUE:
34 ft-lbs. (46 N-m)

9
© 2017 Kolpin Outdoors Inc. REV 03
SPARE KITS
Hard are kit
P/N
33-0070-HDW
Pivot Lock Lever
kit P/N
33-0070-CP04-B
Pivot Lock lever
Bracket kit
P/N 33-0070-CP03
Item Description
3Pivot Lock Lever 1x
4Pivot Lock Lever Bracket 1x
5Blade rip Spring 2x
6Eye Bolt, Zinc Plated, Full hread, M8-1.25 x 110mm 2x
7Blade Stopper Plate 2x
8Lever ension Spring 1x
9Hex Nylon Lock Nut, Zinc Plated, M8-1.25 2x
10 Hex Nylon Lock Nut, Zinc Plated, M12-1.75 2x
11 Hex Nylon Lock Nut, Zinc Plated, M10-1.5 4x
12 Hex Nylon Lock Nut, Zinc Plated, M14-2.0 1x
13 Hex Bolt, Zinc Plated, M10-1.5 x 50mm 1x
14 Large bushing, Ø11mm ID x Ø25 mm OD x 14mm LG 1x
15 Flat washer, Zinc Plated, M10 4x
16 Small bushing, Ø11mm ID x Ø25 mm OD x 8mm LG 1x
17 Hex Bolt, Zinc Plated, M10-1.5 x 35mm 3x
18 Hex Bolt, Zinc Plated, M12-1.75 x 40mm 2x
19 Spring Loop Washer Plate 1x
20 Hex Bolt, Zinc Plated, M14-2.0 x 50mm 1x
Pivot Lock Lever kit
(PN 33-0070-CP04-B)
Pivot Lock Lever Bracket kit
(PN 33-0070-CP03)
Hardware kit
(PN 33-0070-HDW)

10
© 2017 Kolpin Outdoors Inc. REV 03
OPERATION:
WINCH CABLE PUSH FRAME LIFT POINT:
1. he winch lift point for the Kolpin push frame is the round hook hole as shown below. (See illustration 3-1)
ILL. 3-1
Primary hook lift point
ILL. 3-2
Pivot lock lever
Plow pivot point
PIVOTING BLADE ANGLE SIDE TO SIDE:
1. o adjust the angle of the plow blade so it pushes to the side, lift the plow up with the lift mechanism to clear the ground. Pull the
pivot lock lever toward the blade and swivel the plow to desired angle. Release the pivot lever and the plow will lock itself in
place at any of the two angle slot positions on either side. (See illustration 3-2)

11
© 2017 Kolpin Outdoors Inc. REV 03
OPERATION (continued):
SCRAPING ANGLE ADJUSTMENT:
1. urn adjustable plow stoppers to one of the four positions in order to make the plow more aggressive or less aggressive. Position
1 is the position with less material. (See illustrations 3-3 and 3-4)
ILL. 3-3
More aggressive Less aggressive
1234
ILL. 3-4
More aggressiveLess aggressive

12
© 2017 Kolpin Outdoors Inc. REV 03
OPERATION (continued):
BLADE TRIP HINGE FUNCTION:
1. he plow is designed to trip forward when it hits a solid object. When the pressure on the plow is released, it will return to its
original position by itself. (See illustration 3-5)
ILL. 3-5
PLOW TRIPPING FORCE
ADJUSTMENT:
1. he plow trip springs may be set stiffer by tightening the
self-locking nuts located at the ends of the eye bolts. For
less tension, loosen the nuts. (See illustration 3-6)
ILL. 3-6
FASTENER TIGHTNESS:
1. Be sure to frequently check that the (5) fasteners of the pivot
frame assembly are always tight to ensure good system
function. (See illustration 3-7)
ILL. 3-7Fasteners

13
© 2017 Kolpin Outdoors Inc. REV 03
One Year Limited Warranty
For the period of one (1) year from the purchase date, Kolpin will replace for the original purchaser,
free of charge, any part or parts found upon examination by Kolpin to be defective in material,
workmanship, or both.
All transportation costs incurred submitting product to Kolpin for warranty consideration must be
borne by the purchaser. If Kolpin determines that the product must be returned to the factory for
credit, please call 1-877-956-5746 for a Return Merchandise Authorization (RMA) number and
shipping instructions.
his warranty does not apply to parts that have been damaged by accident, alteration, abuse,
improper maintenance, normal wear, or other causes beyond the manufacturer’s control. In order to
protect you and your A V, certain parts of the plow system and/or hardware are designed to fail
when the equipment is over-stressed. Parts that are lost due to loosening and improper
maintenance are not covered under warranty. his warranty does not cover removal or reinstallation
labor fees of the plow system and related components.
Peripheral products such as engines, electric motors, and actuators may carry an original
manufacturer’s warranty. Most hardware is general in nature and is easily obtained locally. Be sure
to replace with minimum metric class 8.8 specification.
Kolpin Outdoors, Inc.
Telephone: [phone]
Toll Free: (877)-956-5746
Fax Number: (800)-245-7569
.kolpin.com
Email: [e-mail]