Kompernass Powerfix KH 4077 User manual

KOMPERNASS GMBH · BURGSTRASSE 21 · D-44867 BOCHUM
www.kompernass.com
ID-Nr.: KH4077-11/07-V1
6
CV_KH4077_BK1968_LB6.qxd 30.11.2007 10:15 Uhr Seite 1

HALOGEN WORK SPOTLIGHTS
Operating instructions
HALOGEN WORK SPOTLIGHTS
KH 4077
CV_KH4077_BK1968_LB6.qxd 30.11.2007 10:15 Uhr Seite 2

CV_KH4077_BK1968_LB6.qxd 30.11.2007 10:15 Uhr Seite 3

KH 4077
w
e
r
t
q
u
y
i
1!
a
o
d
f
g
CV_KH4077_BK1968_LB6.qxd 30.11.2007 10:15 Uhr Seite 4

CV_KH4077_BK1968_LB6.qxd 30.11.2007 10:15 Uhr Seite 5

CV_KH4077_BK1968_LB6.qxd 30.11.2007 10:15 Uhr Seite 6

- 1 -
CONTENT PAGE
Safety instructions 2
Description of the appliance 3
Assembly 3
Removing the halogen lamps. 4
Inserting the halogen lamps 4
Cleaning 4
Troubleshooting 4
Disposal 5
Technical data 5
Service 5
Importer 5
Read these operating instructions carefully before using the appliance for the first time and preserve this
maual for later reference. Pass this manual on to whoever might acquire the appliance at a future date.
IB_KH4077_BK1968_LB6 30.11.2007 14:47 Uhr Seite 1

- 2 -
HALOGEN WORK
SPOTLIGHTS
Safety instructions
 Danger of electrical shock!
• Only connect the Stand Halogen Floodlight to
correctly installed wall sockets having a mains
current of 220 - 240 V at 50 Hz.
• Unplug the Stand Halogen Floodlight from the
socket if you notice any faulty operation and
when you decide to clean it.
• Under no circumstances may the Stand Halogen
Floodlight be immersed in liquids, or liquids be
permitted to permeate into the housing.
Should liquids nonetheless gain entry into the
appliance housing, immediately unplug the ap-
pliance from the mains supply and arrange for it
to be repaired by qualified specialists.
• Never touch the Stand Halogen Floodlight,
power cable or plug with wet hands
• To unplug the appliance, always pull the plug
from the socket, do not pull the cord itself
• Do not crease or crimp the power cable and
place it in such a way as to prevent anyone from
stepping on or tripping over it.
• To avoid the risk of injury, arrange for defective
power plugs and/or cables to be replaced as
soon as possible by a qualified technician or by
our Customer Service Department to avoid the
risk of injury.
• Separate your Stand Halogen Floodlight from
the mains supply immediately after use.The
appliance is only completely switched off after
having been unplugged.
 Danger of injuries
• If they have not previously been supervised or in-
structed in its correct usage, do not allow indivi-
duals (including children) to use the appliance
whose physical, sensorial or mental abilities or
lack of experience and knowledge hinder their
safe usage of it if they have not previously been
supervised or instructed in its correct usage.
• Inform children about the appliance and its
potential dangers and that they should not play
with it.
 Attention
• Always remove the plug from electrical sockets
before exchanging the halogen lamps.
• Allow the halogen lamps to cool before
removing them.
• Switch the Stand Halogen Floodlight off only
with the ON/OFF switch.
• Never touch the glass covering, the power cable
or the metal housing whilst it is in operation.
These parts of the appliance will become very
hot during use.
To avoid burn injuries, do not touch these
surfaces!
• Arrange for a defective glass cover to be imme-
diately replaced by a suitable new one.
• Never direct the halogen floodlights towards
each other. The appliance could be damaged
by the large generation of heat.
• Always ensure that the Stand Halogen Flood-
light is sufficiently distant from yourself and easi-
ly meltable items.
• To avoid eye damage, do not look directly into
the Stand Halogen Floodlight.
• Never place the Stand Halogen Floodlight in the
close proximity of easily inflammable materials.
• Use exclusively halogen lamps up to 500 Watt.
• Never touch the lightbulb with bare hands.
Always use a dry lint-free cloth.
• Read and observe all safety and operating
instructions.
• Ensure that the Stand Halogen Floodlight has
cooled down before storing it away.
IB_KH4077_BK1968_LB6 30.11.2007 14:47 Uhr Seite 2

- 3 -
Description of the appliance
qON/OFF Switch
wFloodlight lever
eHalogen floodlight
rProtective grill
tKnurled screw
yCrossbeam
uTelescopic stand
iPower cable
oKnurled screw
aFixing ring
sDistributor box
dKnurled screw
fFixing screw
gGlass cover
Assembly
 Danger of electrical shock
Never insert the plug into an electrical socket until
the appliance has been completely assembled.
 Danger of burns
Only touch the halogen lamps when they are in a
switched-off and cooled-down condition. The halo-
gen lamps will get very hot. Never touch the light-
bulb with bare hands, always use a clean and dry
lint-free cloth.
Opening up the pedestal base
³To set up the telescopic stand u, loosen the
knurled screw, o. The pedestal base can now
be opened out to the floor.
³Turn the knurled screw ountil it is tight.
Assemble the protective grill ron to
the halogen spotlights e
³Insert the lower pegs of the protective grill r
into the recesses on the corners before the glass
covering g.
³Squeeze the protective grill rso far together
that the pegs on the other side of the protective
grill can be inserted into the recesses there.
³Do the same with the second halogen spotlight
Mounting the halogen floodlights e
on the crossbeam.
³Insert the knurled screw twith the washer
through the hole in the bracket of the halogen
floodlight e.
³Insert the halogen floodlight e with the knurled
screw tin the pre-drilled hole on the crossbe-
am y. Ensure that the Stoppers are located be-
hind the halogen floodlights e.
³Turn the knurled screw tuntil it is tight.
Assembling the crossbeam on the
telescopic stand.
³Insert the knurled screw dfirst of all through the
hole in the distributer box s, then through the
hole in the crossbeam y.
³Now assemble the crossbeam yand the distri-
butor box swith the assistance of the knurled
screw don the telescopic stand u.
³Turn the knurled screw duntil it is tight.
Adjusting the height of the Stand
Halogen Floodlight
³Loosen the fixing ring aby turning it in an
anti-clockwise direction.
³Adjust the telescopic stand uto the desired
height.
³Retighten the fixing ring aby turning it in a clok-
kwise direction.
IB_KH4077_BK1968_LB6 30.11.2007 14:47 Uhr Seite 3

- 4 -
 Important!
To adjust the halogen floodlight e, use the knurled
screw t, the fixing screw fand the floodlight
lever w.
The horizontal position is adjusted in that the knur-
led screw tis loosened and, with the assistance of
the floodlight lever w, it is placed in the desired
position. Retighten the knurled screw twhen the
optimal position has been found.
The vertical position is adjusted in that the fixing
screw fis loosened and and, with the assistance
of the floodlight lever w, it is placed in the desired
position. Retighten the fixing screw, fwhen the
optimal position has been found.
 Important!
During the adjustments always hold the floodlight
lever wfirmly.
 Important!
Do not use extension cables that are longer than
15 m.
Removing the halogen lamps.
1. Switch the appliance off with the ON/OFF
switch q, remove the plug from the socket and
allow the Floor Halogen Floodlight to cool
down.
2. Remove the middle screw on the top of the lamp
housing. Loosen the glass cover g.
3. Use a dry cloth to take out the halogen lamp.
4. Remove the halogen lamp.
Inserting the halogen lamps
1. Ensure that the Floor Halogen Floodlight is
switched-off and completely cooled down.
2. Take the new halogen lamp from its packaging
with a dry cloth. Place a ceramic end on the
appropriate retainer.
3. Place the other ceramic end on the opposite
retainer. Ensure that contact has been made
on both sides. The retainers should now hold the
halogen lamp securely, such that the halogen
lamp can no longer move itself.
4. Now close the glass cover gand replace and
retighten the middle screw.
5. Switch the Floor Halogen Floodlight on with the
ON/OFF switch q.
6. Should it not function, repeat steps 1- 5.
Cleaning
 Danger of electrical shock
Always remove the plug from the socket before cle-
aning the Stand Halogen Floodlight.
Under no circumstances may the appliance be
immersed in water or held under running water
during cleaning.
Clean the exterior of the Stand Halogen Floodlight
with a moist cloth.
 Attention!
Ensure the Floor Halogen Floodlight is inaccessible
for children.
IB_KH4077_BK1968_LB6 30.11.2007 14:47 Uhr Seite 4

- 5 -
Troubleshooting
Symptom:
The Stand Halogen Floodlight will not switch on.
Possible cause and remedy:
Check if the Stand Halogen Lamp has been correct-
ly assembled or if it is possibly damaged. Replace
the halogen lamps if necessary.
A domestic electrical fuse is defect.
Check the domestic fuses and, if necessary, renew
them.
The power socket is defective.
Try another wall socket.
The Floor Halogen Floodlight is possibly defect.
Check the connecting lead and the power plug for
damages. Have the Floor Halogen Floodlight chek-
ked over by specialists.
Disposal
Do not dispose of the appliance in your
normal domestic waste.
Dispose of the appliance through an approved dis-
posal centre or at your community waste facility.
Observe the currently applicable regulations.
In case of doubt, please contact your waste disposal
centre.
Dispose of all packaging materials in an
environmentally responsible manner.
Technical data
Mains voltage: 220 - 240 V ~/ 50 Hz
Rated output: 2 x 500 Watt
Protection rating:IP44
Service
DES Ltd
Units 14-15
Bilston Industrial Estate
Oxford Street
Bilston
WV14 7EG
Tel.: [phone]
Fax: [phone]
e-mail: [e-mail]
Irish Connection
Harbour view
Howth
Co. Dublin
Tel: 00353 (0) 87 99 62 077
Fax: [phone]
e-mail: [e-mail]
Importer
KOMPERNASS GMBH
BURGSTRASSE 21
D-44867 BOCHUM
www.kompernass.com
IB_KH4077_BK1968_LB6 30.11.2007 14:47 Uhr Seite 5