Konica Minolta 7065 User manual

7065
Before copying, read this guide.
Keep in the right hand rear pocket of the machine.
INSTRUCTIONMANUAL

Thank you very much for your purchase of the Konica 7065.
This Manual deals with making copies, correct handling of the machine, and
precautions for safety. Please read before copying.
In order to maintain a satisfactory copying performance, please keep this
Manual readily available for reference in the right hand rear pocket of the
machine.
ENERGY STAR
®
Program
The ENERGY STAR Program has been established
to encourage the widespread and voluntary use of
energy-efficient technologies that reduce energy
consumption and prevent pollution.As an ENERGY
STAR Partner, Konica Corporation, Inc. has
determined that this product meets the ENERGY
STAR guidelines for energy efficiency grounding it on
the following features.
Auto Low Power
This function conserves energy by lowering the set temperature of the fixing
unit. In the standard setting, Auto Low Power operates automatically when 15
minutes have elapsed after completion of the last copy, with the copier remaining
in the ready to copy state during that time.
The time period for the Auto Low Power function can be set for 5 minutes, 10
minutes, 15 minutes, 30 minutes, 60 minutes, 90 minutes, 120 minutes, or 240
minutes. See p.5-2 for details.
Automatic Shut-Off
This function achieves further energy conservation by partially turning OFF the
power supply, thereby reducing energy consumption to 20W or less. In the
standard setting, Automatic Shut-Off follows Auto Low Power, operating
automatically when 90 minutes have elapsed after completion of the last copy,
with the copier remaining in the ready to copy state during that time.
The time period for the Automatic Shut-Off function can be set for 30 minutes,
60 minutes, 90 minutes, 120 minutes or 240 minutes. See p. 5-3 for details.
Automatic Duplex Copying
To reduce paper consumption, use this function to make double-sided (duplex)
copies, automatically.
We recommend that you utilize the Auto Low Power function, the Automatic
Shut-Off function, and the Automatic Duplex Copying function.

Contents
1
2
3
4
5
6
7
8
9
14
15
13
12
11
10
Safety
Information
Machine
Information
Paper
Information
Copier
Management
Basic
Operation
Output
Modes
Tandem
Mode
Scanning
Condition
Applications
Job
Memory
Key Operator
Mode
Maintenance
& Supplies
Trouble-
shooting
Machine
Specifications
Introduction
Section 1: Introduction
Features of the Konica 7065 .........................................................................................1-2
Copier Features ............................................................................................................1-7
Standard Equipment ..............................................................................................1-7
Optional Equipment ...............................................................................................1-7
Section 2 : Safety Information
Caution Labels and Indicator ........................................................................................2-2
Danger, Warning and Caution Symbols ........................................................................2-4
Requirements for Safe Use...........................................................................................2-5
Power Source ........................................................................................................2-5
Environment...........................................................................................................2-7
Precautions for Routine Handling ........................................................................2-10
Section 3: Machine Information
Machine Configuration ..................................................................................................3-2
External Machine Call-outs ....................................................................................3-3
Internal Machine Call-outs .....................................................................................3-3
Standard/Optional Equipment................................................................................3-4
Control Panel Layout.....................................................................................................3-7
Touch Screen ................................................................................................................3-8
Full-Automatic Mode Screen..................................................................................3-8
Basic Screen (Layer Selection Screen) .................................................................3-9
Basic Screen (Direct Selection Screen).................................................................3-9
Initial Settings..............................................................................................................3-10
Auto/Reset Mode ........................................................................................................3-10
Automatic Paper Selection (APS) ...............................................................................3-10
Automatic Magnification Selection (AMS) ...................................................................3-10
Automatic Exposure (AE)............................................................................................3-10
Automatic Tray Switching (ATS)..................................................................................3-10
Lead Edge Delete .......................................................................................................3-11
Service Settings .......................................................................................................... 3-11
Finisher-Paper Capacity ...................................................................................... 3-11
Key Operator Password....................................................................................... 3-11
EKC Master Key Code......................................................................................... 3-11
Weekly Timer Master Key Code .......................................................................... 3-11
Weekly Timer Key in Help Screen ....................................................................... 3-11
Control Panel Contrast Key in Help Screen......................................................... 3-11
Staple Sheet Capacity .........................................................................................3-12
Notice Message: ADD TONER/ PM CALL/ APPLICATION/INTERRUPT ............3-12
Basic Screen Selection ........................................................................................3-12
Section 4: Paper Information
Positioning Originals on the Platen Glass .....................................................................4-2
Positioning an Original for Manual Copying...........................................................4-2
Using the Reversing Automatic Document Feeder (RADF)..........................................4-3
Positioning Originals ..............................................................................................4-4
Positioning Mixed Originals....................................................................................4-5
Paper in Main Body Trays .............................................................................................4-6
Paper in Large Capacity Tray (LT-352) (Option) ...........................................................4-6
Paper in Multi-Sheet Bypass Tray.................................................................................4-6

Contents
Section 4: Paper Information (continued)
Paper in Automatic Duplex Unit ....................................................................................4-6
Paper in FS-106 Finisher (Option) ................................................................................4-7
FS-106 Finisher Primary (Main) Tray.....................................................................4-7
FS-106 Finisher Secondary (Sub) Tray .................................................................4-7
Paper in FS-108BM Finisher (Option)...........................................................................4-8
FS-108BM Finisher Primary (Main) Tray ...............................................................4-8
FS-108BM Finisher Secondary (Sub) Tray ............................................................4-8
FS-108BM Finisher Booklet Tray ...........................................................................4-9
Paper in Cover Sheet Feeder (PI-108) (Option) ...........................................................4-9
Paper in Punching Unit (PU-108) (Option)..................................................................4-10
Paper in Trimmer Unit (TU-108) (Option)....................................................................4-10
Paper Weight Compatibility Chart ...............................................................................4-10
Section 5: Copier Management
Power Saver Mode........................................................................................................5-2
Auto Low Power.....................................................................................................5-2
Manual Low Power ................................................................................................5-3
Auto Shut-Off .........................................................................................................5-4
Manual Shut-Off.....................................................................................................5-4
Entering an EKC Password...........................................................................................5-5
Weekly Timer Function..................................................................................................5-6
Timer Interrupt........................................................................................................5-6
Section 6: Basic Operations
How to Make a Basic Copy ...........................................................................................6-2
The Full-Automatic Mode.......................................................................................6-2
The Basic Screen...................................................................................................6-2
Copy Mode....................................................................................................................6-5
Copy Density.................................................................................................................6-8
Automatic Exposure (AE).......................................................................................6-8
Manual Mode (Lighter, Normal, Darker).................................................................6-8
Userset Density (USERSET 1, USERSET 2) ........................................................6-9
Density Shift......................................................................................................... 6-11
Lens Mode ..................................................................................................................6-13
Automatic Paper Selection (APS) ........................................................................6-13
Automatic Magnification Selection (AMS)............................................................6-14
Preset and User Set Ratios .................................................................................6-15
Zoom Mode..........................................................................................................6-16
Vertical/Horizontal Zoom......................................................................................6-17
Paper size ...................................................................................................................6-19
Reserve.......................................................................................................................6-20
Set Reserve Job ..................................................................................................6-20
Troubleshooting in Reserve Setting .....................................................................6-22
Status ..........................................................................................................................6-24
Memory Copy..............................................................................................................6-26
Platen Memory Copy ...........................................................................................6-26
RADF Memory Copy............................................................................................6-28
Output Mode for Machine without Finisher .................................................................6-30
Rotation.......................................................................................................................6-33
Rotation and APS.................................................................................................6-33

Contents
1
2
3
4
5
6
7
8
9
14
15
13
12
11
10
Safety
Information
Machine
Information
Paper
Information
Copier
Management
Basic
Operation
Output
Modes
Tandem
Mode
Scanning
Condition
Applications
Job
Memory
Key Operator
Mode
Maintenance
& Supplies
Trouble-
shooting
Machine
Specifications
Introduction
Section 6: Basic Operations (continued)
Rotation and AMS ................................................................................................6-34
To Release Automatic Rotation............................................................................6-35
Check Mode and Proof Copy ......................................................................................6-36
Interrupt Mode.............................................................................................................6-40
Help Mode...................................................................................................................6-42
Using the Multi-Sheet Bypass Tray .............................................................................6-43
Section 7: Output Modes
FS-106 Finisher Specifications .....................................................................................7-2
FS-108BM Finisher Specifications ................................................................................7-3
Non-Sort Mode Using Primary (Main) Tray ...................................................................7-5
Sort Mode Using Primary (Main) Tray...........................................................................7-6
Staple-Sort Mode Using Primary (Main) Tray ...............................................................7-7
Group Mode Using Primary (Main) Tray ..................................................................... 7-11
Output Modes Using Secondary (Sub) Tray................................................................7-12
Folding, Stapling & Folding and Trimming Modes (FS-108BM/TU-108)......................7-14
Cover Sheet Feeder (FS-108BM with PI-108) ............................................................7-17
Punching Mode (FS-108BM/FS-106 with PU-108) .....................................................7-19
Manual Stapling (FS-108BM)......................................................................................7-21
Section 8: Original Scanning Condition
Original Scanning Condition Menu................................................................................8-2
Resolution (High Quality) ..............................................................................................8-3
High Mode..............................................................................................................8-3
Very High Mode .....................................................................................................8-5
S600.......................................................................................................................8-7
Text/Photo Enhance......................................................................................................8-9
Original Variety............................................................................................................8-12
Mixed Original ......................................................................................................8-12
Z-Folded Original .................................................................................................8-15
Original Form ..............................................................................................................8-17
Section 9 : Applications
Application Function Menu............................................................................................9-2
Sheet/Cover Insertion ...................................................................................................9-3
Chapter .........................................................................................................................9-9
Combination ................................................................................................................9-12
Booklet ........................................................................................................................9-15
OHP Interleave............................................................................................................9-20
Image Insert ................................................................................................................9-23
Dual Page ...................................................................................................................9-27
Program Job................................................................................................................9-30
Non-Image Area Erase................................................................................................9-32
Reverse Image............................................................................................................9-35
Repeat Image..............................................................................................................9-37
Frame/Fold Erasure ....................................................................................................9-40
AUTO Layout ..............................................................................................................9-43
Thin/Thick Paper .........................................................................................................9-46
Image Shift ..................................................................................................................9-48
Overlay........................................................................................................................9-51

Contents
Section 10: Job Memory
Job Store.....................................................................................................................10-2
Job Recall ...................................................................................................................10-4
Job Memory Form .......................................................................................................10-6
Section 11:Tandem Mode
Operation in Tandem Mode .........................................................................................11-2
To Stop Scanning/Printing...........................................................................................11-5
Troubleshooting...........................................................................................................11-5
Section 12 : Key Operator Mode
To the Key Operator ....................................................................................................12-2
How to Access the Key Operator Mode ...............................................................12-3
Function Menu Map ....................................................................................................12-4
Initial Setting Mode [1].................................................................................................12-6
How to Access the Initial Setting Mode................................................................12-7
Copy Mode [1]......................................................................................................12-8
Copy Density [2]...................................................................................................12-9
Lens Mode [3] ....................................................................................................12-10
Paper Tray [4] .....................................................................................................12-11
Output [5] ...........................................................................................................12-12
Staple [6]............................................................................................................12-13
Image Scan [7]...................................................................................................12-14
Lens Mode Ratio [2] ..................................................................................................12-15
EKC (Electronic Key Counter) [3]..............................................................................12-16
How to Access the EKC Setting Mode...............................................................12-17
Entering and Amending Passwords/User Name [1]...........................................12-18
Entering Account Limits [2] ................................................................................12-20
Resetting the Accounts [3] .................................................................................12-21
Switching the EKC On or Off [4] ........................................................................12-23
Select Effect of Reaching the Copy Limit [5]......................................................12-24
Data Printing Mode ............................................................................................12-25
Lock/Delete Job Memory [4] .....................................................................................12-26
Paper Type [5] ...........................................................................................................12-28
Control Panel Contrast [6].........................................................................................12-29
Key Operator Telephone Number [7].........................................................................12-30
Weekly Timer [8] .......................................................................................................12-31
How to Access the Weekly Timer Setting Mode ................................................12-32
WeeklyTimer On/Off Setting [1] ........................................................................12-33
Summer Time Setting [2] ...................................................................................12-34
Date & Time Setting [3] ......................................................................................12-35
Timer Setting [4].................................................................................................12-36
Timer Action On/Off Setting [5] ..........................................................................12-38
Lunch Hour Off Setting [6] .................................................................................12-40
Timer Interrupt Password Setting [7]..................................................................12-41
Memory Switch [9] ....................................................................................................12-42
Control Panel Adjustment [10] ..................................................................................12-47
Auto Low Power/Auto Shut Off [11]...........................................................................12-48
Call Remote Service Centre [12] ..............................................................................12-50
Save EKC Data to Memory Card [13] .......................................................................12-51
Key Operator EKC Form ...........................................................................................12-52

Contents
1
2
3
4
5
6
7
8
9
14
15
13
12
11
10
Safety
Information
Machine
Information
Paper
Information
Copier
Management
Basic
Operation
Output
Modes
Tandem
Mode
Scanning
Condition
Applications
Job
Memory
Key Operator
Mode
Maintenance
& Supplies
Trouble-
shooting
Machine
Specifications
Introduction
Section 13: Maintenance & Supplies
Loading Paper .............................................................................................................13-2
Add Paper Indicator .............................................................................................13-2
Paper Level Indicator (Tray 5) ..............................................................................13-2
Using the HELP Key ............................................................................................13-2
Tray Error Indicator ( ! ) ........................................................................................13-2
Loading Paper in Tray 1 .......................................................................................13-3
Loading paper in Tray 2........................................................................................13-3
Loading Paper in Tray 3 .......................................................................................13-4
Loading paper in Tray 4........................................................................................13-4
Loading Paper in Tray 5 .......................................................................................13-5
Adding Toner ...............................................................................................................13-6
Inserting a New Staple Cartridge into FS-106 Finisher ..............................................13-8
Inserting a New Staple Cartridge into FS-108BM Finisher .......................................13-10
Empty Waste Basket of TU-108 Trimmer Unit ..........................................................13-12
Empty Waste Basket of PU-108 Punching Unit ........................................................13-13
Preventive Maintenance............................................................................................13-14
Reading the PM Count and Total Count ............................................................13-14
Cleaning the Left Partition Glass...............................................................................13-15
Cleaning the Document Glass and Cover.................................................................13-15
Section 14: Troubleshooting
Call for Service............................................................................................................14-2
Limited Use of the Copier in Trouble ....................................................................14-3
Memory Overflow ........................................................................................................14-4
Copy Conditions Using Memory ..........................................................................14-4
Action 1 ................................................................................................................14-5
Action 2 ................................................................................................................14-6
Power OFF/ON Screen ...............................................................................................14-7
Clearing Mishandled Paper.........................................................................................14-8
Copying Hints............................................................................................................14-10
Section 15: Machine Specifications
Main Body Specifications ............................................................................................15-2
Main Body ............................................................................................................15-2
RADF (DF-312)....................................................................................................15-3
Option Specifications ..................................................................................................15-4
FS-106 In-Bin Stapler Finisher.............................................................................15-4
FS-108BM In-Bin Stapler Finisher .......................................................................15-4
Cover Sheet Feeder (PI-108)...............................................................................15-4
Trimmer Unit (TU-108) .........................................................................................15-5
Punching Unit (PU-108) .......................................................................................15-5
Large Capacity Tray (LT-352) ..............................................................................15-5
Memory unit .........................................................................................................15-5
Key Counter .........................................................................................................15-5
Tandem Kit (TD-101)............................................................................................15-5
Copy Materials ............................................................................................................15-6
Maintenance Kit (150,000 copies) (except for the United Kingdom)....................15-6
Index

Section 1: Introduction
Features of the Konica 7065
Copier Features
Standard Equipment
Optional Equipment
1
Introduction

1 - 2
Section 1 : Introduction
Features of the Konica 7065
• AE - Automatic Exposure
Automatically adjust exposure to compensate for the original.
• Alternate Exit
When no Finisher is installed, alternately switch the horizontal and vertical orientation of
each sorted set as it outputs to the exit tray. Be sure to load both A4/B5 and A4R/B5R in
separate trays other than the Multi-sheet bypass tray.
• AMS - Automatic Magnification Selection
Automatically select an appropriate magnification ratio when Paper Size is selected
manually.In thecase ofthe DirectSelection Screen, automatically select it when [-A-]key
is touched.
• APS - Automatic Paper Selection
Automatically select copy paper size to match the original documents.
• ATS - Automatic Tray Switching
Automatically switch tray to allow copying to be continued without interruption when the
selected tray becomes empty while copying is in progress.
• Auto Layout
The original image on the platen glass is copied and centred on a sheet.
• Auto Low Power
Automatically lower the power after a specified period of copier inactivity.
• Auto Reset
Automatically reset to auto mode defaults after a specified period of copier inactivity.
• Auto Shut-Off
Automatically shut off the main power after a specified period of copier inactivity.
• Booklet
Create A5 or A4 booklets from A4 size originals in 1-2 or 2-2 copy mode.
• Chapter
Start chapter pages on the right side (front pages) of the finished document. Only duplex
mode (1-2 or 2-2) is compatible.
• Combination
Copy a fixed number (2, 4, or 8) of pages onto one sheet of copy paper.
• Copy Density
Manually select up to 9 density levels.
• Copy Mode
Select the desired simplex mode (1-1 or 2-1); or duplex mode (1-2 or 2-2).

1 - 3
Section 1 : Introduction
1
Introduction
Features of the Konica 7065 (continued)
• Data Printing
Print the following three types of data for confirmation; copy quantity for each password,
copy limit for each password, copy quantity for each paper size.
• Density Shift
Adjustdensity levels ofthe four densitymodes (Auto, Text, Photo, IncreaseContrast) into
two levels to lighter and three levels to darker.
• Dual Page
Copy both pages of an open book or book-size sheet separately onto two A4 sheets in 1-
1 mode or separately onto each side of one A4 sheet in 1-2 mode. You can use the Dual
Page mode with the Front or Front/Back cover mode. The cover page(s) will be scanned
and copied normally before image division is performed on the other pages.
• Frame/Fold Erasure
Erase border and/or fold image area using Frame (1 - 15mm), Fold (1 - 30mm), or Frame
& Fold.
• Image Insert
Store pages in memory from the platen glass, and insert the pages into a document
copied from the document feeder.
• Image Rotation
Beforecopying,rotatetheoriginalimagewhenitsportrait/landscapeorientationisdifferent
from the copy paper orientation.
• Image Shift
Create or remove a binding margin (shift amount from -99 ~ 250mm in 1mm increments);
reduce image to prevent image loss (reduce & shift amount from 1 ~ 250mm in 1mm
increments).
• Interrupt Copying
Interruptcopyinginprogresstoperformcopyingfromtheplatenglassordocumentfeeder.
• Job Memory
Program up to 15 jobs and Recall each job by job number or name, as needed. All
compatibleplaten glassfunctions can be programmed intoJob Memorydirectly after they
are selected.
• Lens Mode (Preset, Zoom)
Select Preset ratios, three reduction and three enlargement ratios.
Zoom ratios can be selected from 33% ~ 400% in 1% increments.
• Machine Status Confirmation
Display the current machine status on LCD for confirmation.
• Magnification
Set user-programmable ratios under User Set 1, User Set 2 and User Set 3.

1 - 4
Section 1 : Introduction
Features of the Konica 7065 (continued)
• Manual Shut-off/Low power
Shut off or Low power the main power when pressing [POWER SAVER ON/OFF] key.
• Mixed Original
Copy mixed size originals from the document feeder in APS or AMS mode. APS
automatically selects the copy size of each original. AMS mode allows you to select one
paper size for all originals.
• Non Image Area Erase
When copying from the platen glass when the document cover is open, copy only the
image area and not the exposed area of glass, which would otherwise copy as black.
• Non STD Size
Identifies the special original size which the 7065 could not detect in order to select the
optimal paper size for copying or printing.
• OHP Interleave
Copyontotransparencyfilm and interleaveblankorcopiedpaperforeachoriginalcopied.
• Output for FS-108BM Finisher with PI-108 Cover Sheet Feeder Installed:
Cover Sheet mode
Manual Staple mode
For details of each output mode, see Section 7: Output Modes.
• Output for Machine with FS-106 Finisher Installed:
Non-Sort, Sort, Staple-Sort, and Group modes using the primary (main) tray
Non-Sort Face Down exit, Non-Sort Face Up exit, Group Face Down exit, and
Group Face Up exit modes using the secondary (sub) tray
Select an output tray and output mode on the Output Mode Screen and on the Control
panel. For details of each output mode, see Section 7: Output Modes.
• Output for Machine with FS-108BM Finisher Installed:
Non-Sort, Sort, Staple-Sort, and Group modes using the primary (main) tray
Non-Sort Face Down exit, Non-Sort Face Up exit, Group Face Down exit, and
Group Face Up exit modes using the secondary (sub) tray
Stapling & Folding, and Folding modes using the booklet tray
Select an output tray and output mode on the Output Mode Screen and on the Control
panel. For details of each output mode, see Section 7: Output Modes.
• Output for Machine with no Finisher Installed: Sort and Group modes
Use the default condition to output copies in the same order as the originals. Use the Sort
mode to alternately switch the horizontal and vertical orientation of each copied set upon
exit.UsetheGroup mode tooutputmultiplecopies of eachoriginalwithoutoffsetting them
upon exit.
• Output for Machine with PU-108 Punching Unit Installed:
Punch four holes in output copies.
For details of each output mode, see section7: Output Modes.
• Overlay
Copy multi-originals so that each includes a common image overlay, previously scanned.

1 - 5
Section 1 : Introduction
1
Introduction
Features of the Konica 7065 (continued)
• Paper Capacity
Total 3600 sheets, including two 500-sheet trays, a 1,500-sheet tray, a 1,000-sheet tray,
and a 100-sheet Multi Sheet Bypass tray.
• Platen Memory
Scan documents into memory from the platen glass and/or the document feeder and
insertthepagesintoanotherdocumentcopiedfromthedocumentfeeder.Ifanincompatible
function is selected in this mode, the latter function will not be selected, and a Caution
message will be displayed.
• Power Saver
Automatically turns off all but nominal power supply after a specified period of copier
inactivity,foroptimal efficiency. Powerisreturned after abriefwarm up periodbypressing
[POWER SAVER ON/OFF] key on the Control panel.
• Program Job
Scan documents into memory while designating different tray for each original, then print
all the images collectively. Use this function when copies require several paper types.
• Proof Copy
To ensure correct output before running multiple copies, run a proof copy by touching
PROOF COPY on the Check Screen or pressing [PROOF COPY] key on the Control
panel.
• Repeat Image
Select the horizontal image area across the page, and repeat it down the page as many
times as the repeat width setting (10 ~ 300mm) permits in manual or auto.
• Reserve
Scan in subsequent copy jobs while the 7065 is busy printing or copying.
• Resolution (High, Very High)
High resolution mode and Very High resolution mode provide optimal image quality for
photos and complicated graphics and text which contain a large amount of detail.
• Reverse Image
Reverse the image from black-on-white to white-on-black or vice versa.
• Sheet/Cover Insertion
Insertupto15 blankorcopiedsheets from Tray1,Tray3, ortheMulti-SheetBypass Tray,
or insert blank or copied front and back covers from Tray 1, Tray 3 or the Multi-Sheet
Bypass Tray.
• Staple
Select the stapling position and number of staples.
• Text/Photo Enhance
Enhance photo image in Photo mode; enhance text image in Text mode; enhance lighter
image in increase contrast mode.

1 - 6
Section 1 : Introduction
Features of the Konica 7065 (continued)
• Thin/Thick Paper
Use Thin mode when copy paper weight is less than 60g/m2; use Thick mode when copy
paper weight is over 90g/m2.
• Trimming mode for FS-108BM Finisher with TU-108 Trimmer Unit Installed:
Trim the end of the booklet when selecting the Folding/Stapling & Folding mode.
• Userset Density (USERSET 1, USERSET 2)
Output up to 16 density samples on a total of 4 pages that display 4 samples per page,
then program the desired density under USERSET 1 and/or USERSET 2.
• Weekly Timer
Can be set according to the needs of each work environment. Turn main body power Off/
On daily or weekly, during lunch time, on holidays, and also enable the timer-interrupt
mode, which allows temporary use of the machine even when the machine is in the daily,
weekly, or holiday Off mode.
• Z-Folded Original
This feature set the RADF to accept the Z-folded originals.

1 - 7
Section 1 : Introduction
1
Introduction
Copier Features
Standard Equipment
Main Body with 4 Paper Trays (500/500/1,000/1,500 sheets)
Reversing Automatic Document Feeder (RADF) (DF-312)
Automatic Duplex Unit (ADU)
Configuration Options:
with Multi-Sheet Bypass Tray (100 sheets)
Optional Equipment
Stapler Finisher (FS-106)
This finisher is equipped with two exit trays.
Secondary (sub) tray: Four output types can be specified on the Output Mode Screen.
(1) Non-sort and face down exit
(2) Non-sort and face up exit
(3) Group and face down exit
(4) Group and face up exit
Primary(main)tray:Fouroutputtypescanbespecifiedby[STAPLESORT]and[SORT]
keys on the Control panel and by the setting on the Output Mode Screen. Face up exit
is not available.
(1) Non-sort exit
(2) Sort exit
(3) Staple sort exit
(4) Group exit
Stapler Finisher (FS-108BM)
This finisher is equipped with three exit trays and a cover sheet feeder (option).
Secondary (sub) tray: Four output types can be specified on the Output Mode Screen.
(1) Non-sort and face down exit
(2) Non-sort and face up exit
(3) Group and face down exit
(4) Group and face up exit
Primary(main)tray:Fouroutputtypescanbespecifiedby[STAPLESORT]and[SORT]
keys on the Control panel and by the setting on the Output Mode Screen. Face up exit
is not available.
(1) Non-sort exit
(2) Sort exit
(3) Staple sort exit
(4) Group exit
Booklettray: Stapledand folded, orsimply foldedbooklets areto bedelivered onto this
tray. These two finishing modes can be specified on the Output Mode Screen.
Trimmerunittray:ThistrayisequippedwithaTrimmerunit(option)installedtheStapler
Finsher (FS-108BM). Stapled and Folded simply folded, or trimmed booklets are to be
delivered onto this tray.
Punching Unit (PU-108)
Used when selecting PUNCH on the Output Mode Screen.
Cover Sheet Feeder (PI-108)
Used when selecting COVER SHEET on the Output Mode Screen, or when stapling
copies manually.

1 - 8
Section 1 : Introduction
Copier Features (continued)
Trimmer Unit (TU-108)
Used when selecting TRIM with STAPLING & FOLDING or FOLDING on the Output
Mode Screen.
Large Capacity Tray (LT-352) (3,500 sheets)
Expanded Memory Unit-32MB
Video Interface Kit
Tandem Kit (TD-101)

Section 2 : Safety Information
Caution Labels and Indicator
Danger,Warning and Caution Symbols
Requirements for Safe Use
Power Source
Environment
Precautions for Routine Handling
2
Safety
Information

2 - 2
Section 2 : Safety Information
Caution Labels and Indicator
The caution labels and indicator are attached to the machine areas, as shown below,
where you are advised to pay special attention to avoid any dangerous situations or
serious injury.
CAUTION
If you touch any place which you are advised by any caution label or caution indicator to
keep yourself away from, you may be burned or injured. Do not remove caution labels or
indicators. If any caution label or caution indicator is soiled, please clean to make legible.
If you cannot make them legible, or if the caution label or indicator is damaged, please
contact your service centre.
WARNING
This area generates high
voltage. To avoid an
electrical shock DO NOT
TOUCH.
CAUTION
This internal area is
very hot. To avoid
getting burned DO
NOT TOUCH.
CAUTION
This internal area is
very hot. To avoid
getting burned DO
NOT TOUCH.
CAUTION
The ADU guide plate is not latched
when raised. Do not release it,
otherwise the ADU guide plate will
slam shut and may cause injury.
CAUTION
High temperature!
Do not touch. Use
care when
clearing paper.
CAUTION
High temperature!
Do not touch. Use care when
clearing paper.

2 - 3
Section 2 : Safety Information
2
Safety
Information
Inside the lower paper exit
outlet is the roller drive unit.
DO NOT put your hand into it;
otherwise you may be injured.
Use care after opening the paper exit
outlet. DO NOT put your hand into it;
otherwise you may be injured.
Use care after opening the
paper exit outlet.
DO NOT put your hand into it;
otherwise you may be injured.
CAUTIONCAUTION
CAUTION
FS-108BM Finisher FS-106 Finisher

2 - 4
Section 2 : Safety Information
Danger, Warning and Caution Symbols
The following indicators are used on the caution labels or in this manual to categorize the
level of safety cautions.
DANGER:
Action highly liable to cause a death or serious injury.
WARNING:
Action liable to cause a death or serious injury.
CAUTION:
Action liable to cause light injury, medium trouble or physical damage.
If you find any of these indicators when removing jammed paper, adding toner, or reading
the manual, be sure to follow the information.
Ifthesafety cautionsinthe manualbecomeillegible due tosoilage,etc., pleasebuya new
copy from your service centre.

2 - 5
Section 2 : Safety Information
2
Safety
Information
Requirements for Safe Use
To ensure your safe use of the machine, the following describes the precautions you are
requiredtoobservewithoutfailforthepowersourceofthemachine and during installation
and routine handling. Be sure to read and observe them.
Power Source
CAUTION: Plug Socket
• A plug socket is limited in capacity. Use only a power source with the correct rating for
the machine; otherwise, hazardous situations such as smoking or igniting may occur.
See the following list to match the power supply and power consumption:
a) 230V/50Hz: More than 10A
b) 110V/60Hz: More than 15A
c) 230V/60Hz: More than 10A
d) 127V/60Hz: More than 15A
• Avoid multiple connections in the same outlet. Do not use multiple outlet adaptors.
CAUTION: Power Plug and Lead
• Be sure to insert the power plug firmly into the power socket. Otherwise an accident
may occur as a result of smoking or igniting. If the inserted power plug is loose in the
socket, even after it has been positively inserted, disconnect the plug and contact your
electrical contractor.
• For plug cable equipment, that the socket-outlet shall be installed near the equipment
and shall be easily accessible.
• Do not bend or crush the power lead. If your copier power lead is bent or damaged in
any way, contact your Service Centre immediately. Do not attempt to repair it yourself,
and do not continue to operate the copier. A damaged power lead may result in
overheating, a short circuit, or fire.
• Do not bundle or coil the power lead of the copier. Otherwise an accident may occur
as a result of overheating or fire.
CAUTION: Connecting Multiple Loads to One Socket Outlet Prohibited
Never connect multiple loads to one socket outlet using a multi-outlet extension lead or
branched socket. Otherwise an accident may occur as a result of overheating or fire.
CAUTION: Extension Lead
An extension lead is limited in capacity. Unless the lead has adequate capacity, smoking
and/or igniting may occur, and an accident may be caused from overheating. Should
smokingand/orignitingoccur,contactyourelectricalcontractorimmediately.Ifyourequire
further information about power requirements, power consumption, extension leads,
adapters and connectors, please contact your Konica service centre, and also consult
your electrical contractor.
When using an extension lead with a reel, let out the full length from the reel. Using the
lead in rolled-up condition may result in overheating, smoking and/or igniting.