Konica Minolta DK-701 User manual

4682-7771-01
INSTALLATION MANUAL
DK-701/DK-702/DK-703
Applied Machine: //
for Product Code 4034/4035
Desk
NOTE
•Before installing, be sure to unplug the power cord of the machine.
•Keep all packing materials out of the reach of children.
4682-7771-01E.fm 0 ページ ２００５年２月２５日 金曜日 午前８時２８分

DK-701/DK-702/DK-703
– 1 –
■Unpacking
1. Check that the following accessories are available in the box.
■Installing the Adjusters
1. Using one screw for each stabilizers, attach the two stabilizers to the desk at the
positions shown in the illustration below (one screw D furnished with the Desk).
2. Attach the two adjusters to the desk at the positions shown in the illustration at the left.
1. Desk ...................................................................................................... 1
2. Guide Plate ............................................................................................ 2
3. Adjusters................................................................................................ 2
4. Plastic Plate ........................................................................................... 1
5. Screw A (4 × 8 mm) .............................................................................. 3
6. Screw B* (4 × 10 mm) (May or may not be used.) ................................ 1
7. Screw C (3 × 8 mm) (May or may not be used.).................................... 3
8. Screw D (4 × 10 mm) ............................................................................ 2
9. Washer (May or may not be used.) ....................................................... 1
10. Installation Manual (this manual) ........................................................... 1
* Not included in DK-702/DK-703
1
4021U050AA
23
4619U002AA 4619U005AA
4
5678
4021U071AA
4021U072AA 4021U073AA 4021U074AA 4021U075AA
9
4682U001AA
10
4980U021AA
4682IXC005DA
<DK-701> <DK-703>
4682IXC006DA
<DK-702>
Stabilizers
Adjusters
4682IXC001DA
4682-7771-01E.fm 1 ページ ２００５年２月２５日 金曜日 午前８時２８分

DK-701/DK-702/DK-703
– 2 –
■Adjusting the Adjusters
■Attaching the Desk
1. Place the machine/paper feed unit on top of the desk, ensuring that the two are
aligned properly with each other.
2. Fix the machine on the Desk or the paper feeder unit on the Desk.
（Six screws in the box, one washer in the box, one plastic plate）
•Screws
➀Screw A furnished with the Desk
➁Screw A furnished with the Desk
➂Screw A furnished with the Desk
➃ When setting the machine on the Desk, use the screw B in the box.
When setting the paper feeder unit on the Desk, use the screw C in the box with
the washer.
➄Screw C furnished with the Desk
➅Screw C furnished with the Desk
Fix the plastic plate with screw of ➃ to ➅.
With the wrench (1031-7809-01), adjust the
height of the adjusters (front and back) to
stabilize the unit on the floor.
* The wrench is not enclosed.
CAUTION
Be sure to set the adjusters as specified.
Failure to set the adjusters correctly may
cause the unit to become unbalanced and
fall, possibly resulting in serious injuries.
C4619U001AA
0000U008AA
4682IXC002DA 4682IXC003DA
4682IXC004DC
➁
➂
➃
➄
➅
➀
Plastic Plate
4682-7771-01E.fm 2 ページ ２００５年２月２５日 金曜日 午前８時２８分