Konica Minolta PMT User manual

© 2014 Inepro B.V. All rights reserved
Installation Manual | Konica Minolta Kit ~ Bizhub for
PMT
Konica Minolta Kit ~
Bizhub for PMT
Product Version: 7.2
Version of this manual: 7.2.28

Version 7.2.28 http://www.inepro.com
Table of Contents
Introduction 2
Part List 4
Hardware Setup 8
Set up the PTM 12
........................................................................................................................................................ 121PTM GUI
........................................................................................................................................................ 132 Behaviour
........................................................................................................................................................ 133 Network
........................................................................................................................................................ 144 General Settings

Introduction
PartI

2 - Konica Minolta Kit ~ Bizhub for PMT
Introduction
Introduction
This manual is meant to show how to attach a PTM MFP:
To install this manual we shall:
1. Check the part list, read more on page
2. Prepare and construct the hardware. To read more go to page
3. Set up the PTM, you will find more information on page
4
4
4

Part List
PartII

4 - Konica Minolta Kit ~ Bizhub for PMT
Part List
PartList
Before the PTM is installed make sure all the parts needed are present.
321000 - PTM MFP Multi RFID parts

Version 7.2.28 - 5
321000 - PTM MFP Multi RFID part list
1. 1 x P120650 - PTM Desktop Foil
2. 4 x P273930 - Rubber Foot, adhesive
3. 1 x P275732 - Multi ISO RFID 13,56 MHz Antenne Board
4. 1 x P321160 - PTM LCD Display
5. 1 x P321161 - Touchscreen M4702A
6. 1 x P321180 - PTM Housing back-side
7. 2 x P500007 - Pan-head cross recess screw ISO 7045 - M4 x 20 - Z
8. 2 x P500031 - Pan-head cross recess screw ISO 7045 - M4 x 10 - Z
9. 2 x P500045 - Counter-sunk cross recess screw ISO 7046-1 - M4 x 30 - Z
10. 15 x P500050 - Counter-sunk cross recess screw for plastic M2.2 x 8 - Z
11. 2 x P500060 - Tapping screw DIN 7049-ST3.5 x 9.5-C-H-S
12. 4 x P500206 - Starlock Washer - M4 Normal - H0.5 x OD 8
13. 3 x P500950 - Double-sided tape 25 x 12 x 1.0mm
14. 2 x P501030 - Washer - M4 Normal - H1 x OD 8
15. 2 x P501100 - Ty-rap 10 cm
16. 4 x P501742 - Coupler M4 x 14
17. 1 x P530060 - PTM Housing Top
18. 1 x P530070 - PTM Housing Bottom
19. 1 x P500957 - PTM MFP Double-sided Super Foamtape (Polyethyleen)
20. 1 x 320049 - PTM Connector Board
21. 1 x P277629 - PTM Antenne Cable RFID Multi
22. 1 x P551361 - PTM Sticker
23. 1 x P257685 - Network Patch Cable 3.0m Black (RJ45-RJ45 Bend - Right Angle)
24. 1 x P505014 - Colibri PXA 300
25. 2 x P501031 - Washer - M4 Normal 0.5mm High x 9mm Diameter
26. 1 x P321140 - PTM MFP Bracket
27. 2 x P501302 - Rozetring 4,3 x 12,5 x 3
28. 1 x P274006 - PTM Power Supply
29. 1 x P321200 - Isolator Sheet Colibri
30. 1 x P520214 - Ferrite Core Laird type 28R0669-000
The PTM MFP will have the 2 x P500031 and 2 x P500206 left after assembly.

Hardware Setup
PartIII

8 - Konica Minolta Kit ~ Bizhub for PMT
Hardware Setup
Hardware Setup
Additional requirements:
·Pair of wire cutters
·No. 2 cross head screwdriver
·No. 1 PosiDriv head screwdriver
·PTM MFP
·2x CAT-5 Network cables (one 90 degree angled cable included)

Version 7.2.28 - 9
Attach the PTM bracket to the copier
1. Attach the bracket to the copier with the
foam tape and screws.
2. Attach the PTM to the bracket with the M4
x20 screws and their hooded washers. Make
sure the network cable and power supply cable
are already into place before screwing the PTM
on the bracket.

10 - Konica Minolta Kit ~ Bizhub for PMT
Hardware Setup
Attach the PTM to the PTM bracket
3. Use the ty-raps to feed the cable to the back of the machine.

Set up the PTM
PartIV

12 - Konica Minolta Kit ~ Bizhub for PMT
Set up the PTM
Set up the PTM
Turn on the PTM. Refer to the technical PTM Copy manual for handling the PTM menu and changing settings.
The settings in the PTM can be find in the tree-top menu structure of the PTM. To simplify thing, we will use a graphic
representation of this menu to show you where the setting can be found.
BE WARE! The icons depicted below are no longer correct in the new Graphical User Interface, and the flag
function currently does not work! These will be mutated in this manual at a later date.
The steps are represented by icons:
Present your service card and enter the menu
Optional ECOS module
Press 1
Press Dot
Press 2
Press 0
Press 3
Press #
Press 4
Press +
Press 5
Press -
Press 6
Press F
Press 7
Press
Press 8
Press ?
Press 9
Press the Flag
Press
Press Correction
Use the , , and to navigate, the to edit the value, the to confirm and the to cancel.
Look for all the actions of the buttons in the PTM technical manual.
PTM GUI
In order to operate the PTM, the GUI must be set to "Touchscreen". If this is not done, only a white screen will show.
Because this setting influences the GUI itself, this must be done using the PayCon Config Tool.
1. Test if you can enter the GUI by presenting a valid contact-less service card and logging in.
2. If everything is correct the menu will show, if so continue to the next section.
3. If not, the display will be filled with white. Use the PayCon Config Tool to enter the menu and go to the "hardware\User
Interface" menu.
4. From the Hardware menu, go to "../Customer Interface", "..\Employee Interface" and "..\Menu Interface" and set all
these to "Touchscreen".

Version 7.2.28 - 13
Behaviour
Behaviour
1. Where is the credit value kept?
a. On the card (SVC), you will need to use cards of the chipcard or Mifare card type and the ECOS 'KM - PTM
Payment Option', continue with step 2.
b. On the server (SVS), go to step 3.
c. On the PTM terminal, you will need ECOS 'KM - I - Local Accounts', go to step 4.
2. Stored Value on Card:
a. If you use Mifare continue with 2b, if you use chipcards go to step 2d
b. , Go to 'Main Menu' => 'Card / ID' => 'ID Tags' => 'Mifare' => 'Mode'.
c. Select 'Disabled', press and go to step 2f.
d. , Go to 'Main Menu' => 'Card / ID' => 'Server Accounts' => 'Tags' => 'Inepro SLE'.
e. Select 'Disabled' and press .
f. Do you use Pcounter? if you do, continue with step 3, if you don't, go to step 8.
3. Do you use Cost Centres (Client Codes) in the PTM System*?
* Sub Client Codes are not supported.
a. , Go to 'Main Menu' => 'Card / ID' => 'General Settings' => 'Cost Centre Selection'.
b. If everybody is required to use a Cost Centre (Client Code), choose 'Required' and confirm with . The users will
not be able to use budget purses if there is no server connection.
c. If you don't use Cost Centres, choose 'Never' and confirm with .
d. If you only want to use it if the server is online, choose 'If online' and confirm with .
e. Go to step 5.
4. Store Value on Terminal:
a. Set the account mode. , Go to 'Main Menu' => 'Card/ID' => 'Terminal Accounts' => 'Account Mode'.
b. If you want all tags to be accepted select 'Allow all ID's' and confirm with and go to step 4e.
c. If you want to accept only tags that are registered in your PTM select 'Allow accounts' and confirm with .
d. Setting up the accounts:
·, Go to 'Main Menu' => 'Card/ID' => 'Terminal Accounts' => 'Add'.
·Type a card or account number and confirm with to add an account.
·Repeat this until all accounts are set.
e. Setting the tags:
·, Go to 'Main Menu' => 'Card / ID' => 'Server Accounts' => 'Tags' => <Tag Type>.
·Select 'Disabled' and press .
·, Go to 'Main Menu' => 'Card / ID' => 'Terminal Accounts' => 'Tags' => <Tag Type>.
·There are two ways to present a tag to the PTM, you can swipe it past the reader or hold it in place on the reader.
·Select 'Hold' or 'Swipe' and confirm with .
f. Go to Step 8
Network
5. Network Settings:
a. , Go to 'Main Menu' => 'Terminal' => 'Network'
b. Set the 'host name' to an identifiable name.
c. Confirm with .
d. If DHCP is used and go to step 7.
e. If DHCP isn't used, set it to 'disabled' and confirm with .

14 - Konica Minolta Kit ~ Bizhub for PMT
Set up the PTM
6. Fixed IP addresses:
a. Set 'IP-address' to an IP-address in your network range and confirm with .
b. Set the subnet mask ('netmask') to '255.255.255.0' or to the subnet mask needed in your network and confirm with
.
c. Set the 'default gateway' to the IP-address of the default gateway in your network and confirm with .
7. DB Settings:
a. , Go to 'Main Menu' => 'DB Connectivity' => 'Server'
b. Set the IP-address of the PCounter server in 'Sever Address' and confirm with .
c. , Go to 'Main Menu' => 'DB Connectivity' => 'Transaction log'
d. Select 'Enabled' and confirm with .
e. , Go to 'Main Menu' => 'DB Connectivity' => 'Printjob client'
f. Select 'Enabled' and confirm with .
General Settings
8. Copier Interface:
a. , Go to 'Main Menu' => 'Copier' => 'Interface'
b. Select the Interface setting for your machine and press .
9. Products. The copy/print/scan products in the PTM have a fixed order and number. They are used to connect the
paper signals form the copier to prices in the PTM. These products and their names can also be set with PCounter.
a. , Go to 'Main Menu' => 'Products' => 'Product List'
b. Check if the default product list is complete, if so go to step 11, if not continue with step 10.
PTM
product
number
PTM product display
name
PTM
default
price
Corresponds with photocopier product
Supportedby
C350
Others
0
A4 b/w
€ 0,05
A4 black and white
1
A3 b/w
€ 0,10
A4 black and white
2
A4 colour
€ 0,50
A4 colour (single until full)
3
A3 colour
€ 1,00
A3 colour (single until full)
4
A4 b/w dpx
€ 0,05
Backside of duplex A4 black copy
5
A3 b/w dpx
€ 0,10
Backside of duplex A3 black copy
6
A4C dpx
€ 0,50
Backside of duplex A4 colour copy
7
A3C dpx
€ 1,00
Backside of duplex A3 colour copy
1000
Print A4 b/w
€ 0,05
A4 black and white print
1001
Print A3 b/w
€ 1,00
A3 black and white print
1002
Print A4C
€ 0,50
A4 colour print
1003
Print A3C
€ 1,00
A3 colour print
1004
Print A4 b/w dpx
€ 0,05
A4 black and white duplex print
1005
Print A3 b/w dpx
€ 0,10
A3 black and white duplex print
1006
Print A4 colour dpx
€ 0,50
A4 colour duplex print
1007
Print A3 colour dpx
€ 1,00
A3 colour duplex print
2000
Scan A4 b/w
€ 0,01
A4 black and white scan
2001
Scan A3 b/w
€ 0,02
A3 black and white scan
2002
Scan A4C
€ 0,03
A4 colour scan
2003
Scan A3C
€ 0,06
A3 colour scan
3000
Fax A4
€ 0,05
A4 black and white fax
3001
Fax A3
€ 0,10
A3 black and white fax
3008
Fax Start
€ 0,25
Start tariff for fax
X = Supported
-= Not supported
10. Edit Product:
a. To add a product, go to 'Add product', enter a number and press .
b. To edit it's properties, go to 'Main Menu' => 'Products' => 'Product List', select it and press .
c. Check the price and if the index number corresponds with the copy product index number in the table.

Version 7.2.28 - 15
General Settings
11. Purse Selection, manage the way the purse is selected.
a. , Go to 'Main Menu' => 'Card/ID' => 'Generic Settings' => 'Purse Selection'.
b. Select the selection behaviour in the list (look for a description in the table) confirm with .
Purse Selection
Description
All Purses
Accept all purses
Personal Only
22/Only accept personal credit
Budget Only
Only accept non-personal budget
Prefer Personal
If the card has a personal credit, pay out of that credit
Prefer Budget
If the card has a non-personal budget, pay out of that budget
Personal + Ask
Ask which budget and select personal credit as default
Budget + Ask
Ask which budget and select non-personal budget as default
12. Maximum Balance, the Maximum Balance allowed on a card or account.
a. , Go to 'Main Menu' => 'Card/ID' => 'Generic Settings' => 'Maximum Balance'.
b. Type in the maximum balance and confirm with .
13.Project ID, the unique number for all PTM's on this project or site.
a. , Go to 'Main Menu' => 'Terminal' => 'Project ID'
b. Press , type the Project ID and confirm with .
14. Date and Time, the time and date that are used for the timestamp on the transactions. Remember if the time zone is
changed the time will change accordingly.
a. So first set the time zone by , go to 'Main Menu' => 'Terminal' => 'Date/Time' => 'Time zone'.
b. Select the time zone and confirm with .
c. Check the time (go to 'Main Menu' => 'Terminal' => 'Date/Time' => 'Time') and change it if needed.
d. In the same manner check the date.
15. Currency, the currency used in the PTM
a. , Go to 'Main Menu' => 'Terminal' => 'Currency' => 'Accepted Currency'.
b. Select the currency and confirm with .
c. Go to 'Main Menu' => 'Terminal' => 'Currency' => 'Old Currency'.
d. Select the currency and confirm with .
16. Default language, the language the PTM uses to communicate with the user. A second and third language can also
be set. When the user presses , the next available language will be used.
a. , Go to 'Main Menu' => 'Terminal' => 'Default Language'.
b. Select a language from the list and confirm with .
c. Go to 'Main Menu' => 'Terminal' => '<Nth> Language' to add extra languages in the same way.