Konica Minolta BIZHUB C250 User manual

Page 1 of 25
AD_NDS_SMB userauthentication set-up_ver_1_10.doc
Setting-up uide for
bizhub C250/C351/C450/420/500/600/750
User Authentication
In combination with
Active Directory environment
NDS environment
SMB /NTLM environment

Page 2 of 25
AD_NDS_SMB userauthentication set-up_ver_1_10.doc

Page 3 of 25
AD_NDS_SMB userauthentication set-up_ver_1_10.doc
KONICA MINOLTA BIZHUB C250 / C351 / C450 / 750 / 600 – SETTING-UP OF USER
AUTHENTICATION ON ACTI E DIRECTORY........................................................................................... 4
P REPARATION ...................................................................................................................................................... 4
C HECK TCP/IP SETTINGS ..................................................................................................................................... 4
C ONFIGURE U SER AUTHENTICATION (A CTIVE D IRECTORY ) ................................................................................ 7
KONICA MINOLTA BIZHUB C250 / C351 / C450 / 750 / 600– SETTING-UP OF USER
AUTHENTICATION ON NO ELL NDS........................................................................................................ 12
C ONFIGURE U SER AUTHENTICATION (NDS) ...................................................................................................... 12
KONICA MINOLTA BIZHUB C250 / C351 / C450 / 750 / 600– SETTING-UP SMB/NTLM USER
AUTHENTICATION ......................................................................................................................................... 17
C ONFIGURE U SER AUTHENTICATION (SMB/NTLM) ......................................................................................... 17
APPENDIX .......................................................................................................................................................... 22
W HERE TO FIND RE UIRED I NFORMATION ......................................................................................................... 22
T HINKS WHICH MAKES YOUR LIFE EASIER .......................................................................................................... 23
U PDATES IN THIS D OCUMENT RELEASE .............................................................................................................. 25

Page 4 of 25
AD_NDS_SMB userauthentication set-up_ver_1_10.doc
Konica Minolta bizhub C250 / C351 / C450 / 750 / 600 – Setting-up of ser authentication on
Active Directory
This chapter described the setting-up procedure for User Authentication function in combination with a
MS Windows server supporting Active Directory. It’s mandatory that the C450 is connected to a
TCP/IP network and the correct TCP/IP settings are applied to it.
Preparation
Before setting up user authentication, please collect following information. If you have difficulties to
find the required information, please refer to the appendix “Where to find required Information:
MFP’s Administrator password
MFP’s IP address
Subnet Mask
Default gateway (optional)
Priority DNS Server address
Substitute 1 DNS Server address (optional)
Substitute 2 DNS Server address (optional)
MFP’s DNS Host Name
MFP’s DNS Domain Name
Default Domain Name
Valid user account and Password for function
check
Check TCP/IP settings
a) Press the tility key on the Operation panel

Page 5 of 25
AD_NDS_SMB userauthentication set-up_ver_1_10.doc
b) Select “Administrator Setting”
c) Enter the Administrator Password and touch the “OK”-button.
d) Select “Network Setting”

Page 6 of 25
AD_NDS_SMB userauthentication set-up_ver_1_10.doc
e) Select “TCP/IP Settings”
f) Ensure that the right TCP/IP configuration is applied and select the Forward button (FWD. )
g) Ensure that at least the Priority DNS Server IP address is set. If no DNS server address is
set, “User Authentication” and “LDAP search with SS-SPNE O authentication” will not
work. Select the Forward button (FWD. )

Page 7 of 25
AD_NDS_SMB userauthentication set-up_ver_1_10.doc
h) Enter the DNS Default Domain Name and select the Forward button (FWD. ).
i) Enter the DNS Host Name and press “OK”
Configure ser authentication (Active Directory)
a) Enter the Administrator Mode and select “ ser Authentication / Account Track”

Page 8 of 25
AD_NDS_SMB userauthentication set-up_ver_1_10.doc
b) Select “General Settings”
c) Select User Authentication “ON (External Server)”
d) Choose “Active Directory”

Page 9 of 25
AD_NDS_SMB userauthentication set-up_ver_1_10.doc
e) Select the field (button) “01” and touch “Registration” in order to register the domain name of
the domain against the user authentication shall take place.( up to 20 domain different domain
names can be registered).
f) Enter the Domain Name and press “OK”
g) Leave the registration screen by touching “OK”

Page 10 of 25
AD_NDS_SMB userauthentication set-up_ver_1_10.doc
h) Leave the External Server Authentication screen by touching “OK”
i) Leave the general settings screen by touching “OK”
j) In order to activate “User Authentication” this message has to be confirmed by touching the
[Yes] button. Please be aware that this will clear all previous programmed accounting and
Authentication data.

Page 11 of 25
AD_NDS_SMB userauthentication set-up_ver_1_10.doc
k) Try to login with a valid user account name and password. If you face any difficulties to login,
please re-check all settings and refer to the appendix – known issues.

Page 12 of 25
AD_NDS_SMB userauthentication set-up_ver_1_10.doc
Konica Minolta bizhub C250 / C351 / C450 / 750 / 600– Setting-up of ser authentication on
Novell NDS
This chapter described the setting-up procedure for User Authentication function in combination with a
Novell Netware Server Ver. 5 and later.
Preparation
Before setting up user authentication, please collect following information. If you have difficulties to
find the required information, please refer to the appendix “Where to find required Information:
MFP’s Administrator password
Default NDS Tree Name
Default NDS Context Name
Valid user account name and Password for
function check (admin credential will not work,
due to Netware security setting)
Configure ser authentication (NDS)
a) Press the “ tility” key on the Operation panel

Page 13 of 25
AD_NDS_SMB userauthentication set-up_ver_1_10.doc
b) Select “Administrator Setting”
c) Enter the Administrator Password and touch the “OK”-button.
d) select “ ser Authentication / Account Track”

Page 14 of 25
AD_NDS_SMB userauthentication set-up_ver_1_10.doc
e) Select “General Settings”
f) Select User Authentication ”ON (External Server)”
g) Choose “NDS”

Page 15 of 25
AD_NDS_SMB userauthentication set-up_ver_1_10.doc
h) Select “Default NDS Tree Name”
i) Input the default NDS tree name and touch the “OK” button
j) Select “Default NDS context name”

Page 16 of 25
AD_NDS_SMB userauthentication set-up_ver_1_10.doc
k) Input the default NDS context name and touch the “OK” button
l) Leave the administrator mode and switch off and on the main device
l) Try to login with a valid user account and password. If you face any difficulties to login, please
re-check all settings and refer to the appendix – known issues.

Page 17 of 25
AD_NDS_SMB userauthentication set-up_ver_1_10.doc
Konica Minolta bizhub C250 / C351 / C450 / 750 / 600– Setting-up SMB/NTLM ser
authentication
This chapter described the setting-up procedure for User Authentication function in combination with a
Windows PC or a Computer running Samba service.
Preparation
Before setting up user authentication, please collect following information. If you have difficulties to
find the required information, please refer to the appendix “Where to find required Information:
MFP’s Administrator password
Default Domain Name
Valid user account and Password for function
check (admin credential will not work, due to
Netware security setting)
Configure ser authentication (SMB/NTLM)
b) Please ensure a basic TCP/IP configuration of the MFP. IP-address and subnet mask must be
programmed. All other TCP/IP settings are optional.
c) Press the Utility key on the Operation panel

Page 18 of 25
AD_NDS_SMB userauthentication set-up_ver_1_10.doc
e) Select “Administrator Setting”
f) Enter the Administrator Password and touch the “OK”-button.
g) select “ ser Authentication / Account Track”

Page 19 of 25
AD_NDS_SMB userauthentication set-up_ver_1_10.doc
h) Select “General Settings”
i) Select User Authentication “ON (External Server)”
j) Choose [NTLM v1] for user authentication against a SAMBA server, or [NTML v2] for user
authentication against a Windows Server.
OR

Page 20 of 25
AD_NDS_SMB userauthentication set-up_ver_1_10.doc
k) Select “Default Domain Name”
l) Input the default Domain Name by using capital characters and touch the “OK” button
m) Leave the administrator mode and switch off and on the main device