Konica Minolta CF2002 Manual

4581-7777-01 © MINOLTA CO., LTD. Printed in Japan
SETUP INSTRUCTIONS
PRINTER PANEL 1
CF2002/CF3102 Printer
WARNING
• Do not plug in the power cord or turn on this unit until you are instructed to according to this manual.
CAUTION
• Install this machine so that it can quickly be unplugged from the electrical outlet in case of an
emergency. The socket-outlet shall be installed near the machine and shall be easily accessible.
• Keep all packing materials out of the reach of children.
NOTE
• Keep all packing materials in a safe place for later use in case they are needed for transportation.

Printer Panel 1
– 1 –
4581-7777-01
1. Outline of the CF2002/CF3102 System Setup
These Setup Instructions describe the setup for the parts marked in grey in the flowchart
shown below.
When setting up a system consisting of the printer and its various options, perform the
setup according to the procedure described below.
NOTE
•Install and setup each option according to the instructions included with the option.
•For information on adjusting the PF-118, PF-121 and AD-14, refer to the section
“Adjusting the Options”on pages 27 to 31 of these Setup Instructions.
9. Mechanical Counter
7. Duplex Unit AD-14
5. Control Panel
4. Printer
1. Copy Table CT-2
2-C. Copy Desk CD-2M
2-A. Paper Feed Unit PF-118 2-B. Large Capacity Cabinet
PF-121
3-A. Dehumidifying Heater
6. Printer Controller/
Interface kit 10-A. Finisher FN-8 10-B. Finisher FN-116
3-B. Dehumidifying Heater
*: U.S.A and Canada only
4: Printer
Unpack the unit, install it, adjust it using the servicing equipment, and
then calibrate the gradation levels with the X-Rite.
5: Control Panel
Attach the control panel to the printer.
6: Printer Controller/Interface Kit
Attach the printer controller, and then specify the necessary settings.
8. Data Terminal DT-105*
11-A. Punch KIT PK-4 11-B. Option tray JS-100
C4581U019AA

Printer Panel 1
– 2 –
4581-7777-01
1.1 Precautions Concerning the Package Contents (Manuals)
The following manuals for the products listed below are included.
NOTE
Manuals that cannot be used with the printer are also included.
■
■■
■Printer
• User Manual for a copier*
• Setup Instructions for a copier*
■
■■
■Printer Panel 1
• User Manual for a printer (including information on PageScope Light)
• Setup Instructions for a printer (this manual, including information on the printer con-
troller and interface kit)
■
■■
■Interface Kit P
• User Manual for a copier (PageScope Light and Scan mode)*
• Installation Guide for a copier (printer controller and interface kit P)*
■
■■
■Controller
• Controller User Manual
*:Cannot be used with the CF2002/CF3102 printer.
1.2 Precautions Concerning the Installation of the Controller
When installing the printer controller onto a printer that has the duplex unit attached, the
printer memory must have 512 MB.

Printer Panel 1
–3 –
4581-7777-01
2. Unpacking
2.1 Unpacking the Accessories
Remove the accessories from the box, and then check that the following are enclosed.
(1) Imaging units..................................................................................................... 4
(2) Power cord *1.................................................................................................... 1
(3) LED cleaning tool *2.......................................................................................... 1
(4) LED cleaning paper *2 ...................................................................................... 1
(5) Manual holder ................................................................................................... 1
(6) User Manual...................................................................................................... 1
(7) Setup Instructions ............................................................................................. 1
(8) Warranty card *3 ............................................................................................... 1
(9) Power cord instruction *1 .................................................................................. 1
(10) Paper size label................................................................................................. 1
(11) Cable clamp ...................................................................................................... 1
(12) Cap.................................................................................................................... 1
*1 For Particular area only.
*2 The LED cleaning tool and its paper are not used during setup. Since they will be
needed when the transfer belt unit is changed or the printer is cleaned, keep them
in a safe place for later use.
*3 U.S.A. and Canada only.
2.2 Unpacking the Printer
1. Open the printer box, and then remove the box containing the imaging unit.
2. Open the two handle covers, and then pull out the handles.
4025U018AA
3. Grasp the two handles on the right side of
the printer and the two grips on the left (as
shown in the illustration), and then, while
keeping the printer level, remove it from its
box.
NOTE
The printer weighs about 85 kg (187-1/4 lbs.).
The printer must be lifted by at least two peo-
ple.
4025U019AA

Printer Panel 1
–4 –
4581-7777-01
2.3 Removing the Protective Tape and Packing Materials
1. Remove the tape affixed to the outside sur-
face of the printer.
4025U020AA
4025U021AA
Paper take-up
roller
Packing
material
2. Slide out the 1st drawer and remove protec-
tive tape and packing materials from the
inside of the drawer.
3. Close the paper drawer.
C4004U024AA
4. Slide out the 2nd drawer and remove protec-
tive tape and packing materials from the
inside of the drawer.
5. Close the paper drawer.
C4004U026AB
Paper take-up
roller
Packing
material
Ta p e s

Printer Panel 1
–5 –
4581-7777-01
3. Installing the Unit
3.1 Installing the Imaging Unit
1. Open the front door.
2. Pinch the Imaging Unit release lever for Yel-
low and pull it down forward.
C4004U047AA
3. Slide out the protective material.
4025U022AA
4. Take out the Yellow Imaging Unit from the
Imaging Unit carton.
5. Remove the Imaging Unit from its aluminum
package.
6. Remove protective tape and packing mate-
rial.
NOTE
Do not peel off the interference preventive
sheet.
4025U074AC
Protective tape
Interference
preventive sheet
Packing
material
7. Tilt the Imaging Unit to the left and, in that
condition, shake it over a small stroke twice.
Then, tilt the Imaging Unit to the right and, in
that condition, shake it over a small stroke
twice.
4025U024AA
8. Support the Imaging Unit with both hands
and hold it levelly.
4025U026AC

Printer Panel 1
–6 –
4581-7777-01
9. Keeping the Imaging Unit in the level posi-
tion, insert the Imaging Unit into the mount-
ing position on the printer until its leading
edge is stopped.
Make sure that the interference preventive
sheet is left attached to the Imaging Unit
when the Imaging Unit is inserted into the
printer.
NOTE
Make sure the protective sheet is rolled up into
the Imaging Unit, then insert Imaging Unit into
the Printer.
4025U027AA
10. Check that the Imaging Unit is inserted posi-
tively in position.
NOTE
The positioning rib at the leading edge of the
Imaging Unit cover should be fitted positively
in the hole in the mounting position on the
printer.
4025U028AC
11. Supporting the underside of the Imaging
Unit with your left hand, hold the portion of
the unit shown in the illustration with your
right hand and gently push it into position
until a click is heard.
4025U029AB
12. Pull out the empty Imaging Unit cover.
4025U030AB
13. Push the Imaging Unit release lever of Yel-
low all the way until a click is heard.
14. Using the same procedure, install all Imag-
ing Units.
4025U031AA

Printer Panel 1
–7 –
4581-7777-01
3.2 Installing the Toner Cartridge and the Filter
NOTE
Toner does not come with the printer. Purchase toner cartridges (of different colors) sep-
arately available.
1. Open the front door.
2. Holding the toner cartridge firmly, shake it
well vertically and horizontally to agitate
toner.
C4025O220AB
3. Remove the protective tape.
C4025O221AB
4. Swing the fixing lever downward.
5. Load the toner cartridge in position.
(Make sure that the gear is on the rear side.)
4025U038AA
6. Swing the fixing lever upward to fix the toner
cartridges in position.
* Make sure that the fixing lever is positively
swung into position.
7. Using the same procedure, install the toner
cartridges for other colors of toner.
4025U039AA
8. Take out the filter and install it in position.
NOTE
The filter is packed in the box of a black toner
cartridges.
C4025U001AA

Printer Panel 1
–8 –
4581-7777-01
4. Affixing the Label 5. Installing the Manual Holder
Label 1. Affix the label on the right side of the top of
the front door.
NOTE
Affix the label that corresponds with the
installed options.
C4004U589AA
1. Insert the tab on the bottom of the manual
holder into the slot in the printer as shown in
the illustration.
C4004U553AA
2. Insert the tabs on the left and right sides of
the manual holder into the corresponding
slots in the printer.
C4004U554AA
NOTE
If the optional finisher is used, attach the man-
ual holder to the back of the finisher at the
position shown, using the same procedure
described above.
C4004U098AA

Printer Panel 1
–9 –
4581-7777-01
6. Connecting the Cables
1. Make sure that the printer power cord is not
plugged into the electrical outlet, and then
insert the plug on the end of the power cord
into the power cord connector on the printer.
C4581U021AA
2. Insert the plug on the other end of the power
cord into an electrical outlet.
C4004U139CA