Kontron coolMONSTER/P3 User manual

coolMONSTER/P3
coolMONSTER/C3
User’s Guide
Document Revision 2.2

KONTRON
CMP/P3 and CMP/C3 User’s Guide Contents
1
CONTENTS
1. USER INFORMATION.............................................................................................. 1
1.1 About This Manual........................................................................................... 1
1.2 Copyright Notice............................................................................................. 1
1.3 Trademarks.................................................................................................... 2
1.4 Standards...................................................................................................... 2
1.5 Warranty ....................................................................................................... 2
1.6 Technical Support ........................................................................................... 3
2. INTRODUCTION ...................................................................................................... 4
2.1 coolMONSTER/P3 and coolMONSTER/C3............................................................... 4
2.2 The coolMONSTER PISA® Family......................................................................... 4
3. GETTING STARTED................................................................................................ 5
4. SPECIFICATIONS.................................................................................................... 6
4.1 Functional Specifications ................................................................................. 6
4.2 Mechanical Specifications................................................................................. 8
4.3 Electrical Specifications ................................................................................... 8
4.3.1. Supply Voltage ............................................................................................ 8
4.3.2. Supply Voltage Ripple ................................................................................... 8
4.3.3. Supply Current (typical) ................................................................................ 8
4.3.4. Supply Current (maximum) ............................................................................ 9
4.3.5. Real-time Clock (RTC) Battery ......................................................................... 9
4.4 MTBF ...........................................................................................................10
4.5 Environmental Specifications ...........................................................................10
4.5.1. Temperature ..............................................................................................10
4.5.2. Humidity ...................................................................................................11
5. CPU, CHIPSET, AND SUPER I/O.......................................................................... 12
5.1 CPU.............................................................................................................12
5.2 Chipset ........................................................................................................12
5.3 Super I/O .....................................................................................................13
6. VIDEO CONTROLLER........................................................................................... 14
6.1 Video Subsystem Block Diagram........................................................................14
6.2 Supported Display Types..................................................................................15
6.2.1. Current Panel Information ............................................................................15
6.2.2. Available Video Modes .................................................................................15
7. SYSTEM MEMORY................................................................................................ 17
8. PISA BUS............................................................................................................... 18
9. FRONT PANEL ...................................................................................................... 19

KONTRON
Contents 2 CMP/P3 and CMP/C3 User’s Guide
10. KEYBOARD AND MOUSE INTERFACES............................................................. 20
10.1 Keyboard Connector .......................................................................................20
10.2 Mouse Connector ...........................................................................................20
10.3 Configuration................................................................................................20
11. USB INTERFACE................................................................................................... 21
11.1 Connector ....................................................................................................21
11.2 Configuration................................................................................................21
12. ETHERNET INTERFACE ....................................................................................... 22
12.1 Connector ....................................................................................................23
12.2 Configuration................................................................................................23
13. GRAPHIC INTERFACES ....................................................................................... 24
13.1 CRT Connector ...............................................................................................24
13.2 Flat Panel LVDS Interface (JILI) Connector..........................................................24
13.3 Configuration................................................................................................25
14. SERIAL-COMMUNICATION INTERFACES .......................................................... 26
14.1 Serial Ports COMA-D .......................................................................................26
14.2 RS-232 Connectors.........................................................................................26
14.3 Configuration................................................................................................27
14.4 RS-485 Connector ..........................................................................................27
14.5 Configuration................................................................................................27
14.5.1. RS-485 Diagram.......................................................................................28
15. IRDA INTERFACE.................................................................................................. 29
15.1 IrDA SIR Mode ...............................................................................................29
15.2 Connector ....................................................................................................29
15.3 Configuration................................................................................................30
16. PARALLEL-PORT INTERFACE ............................................................................ 31
16.1 Connector ....................................................................................................31
16.2 Configuration................................................................................................32
17. EIDE INTERFACES................................................................................................ 33
17.1 Connector ....................................................................................................33
17.1.1. Primary EIDE Pinout..................................................................................34
17.1.2. Secondary EIDE Pinout ..............................................................................35
17.2 Signal Descriptions ........................................................................................36
17.3 Configuration................................................................................................36
18. FLOPPY INTERFACE ............................................................................................ 37
18.1 Connector ....................................................................................................37
18.2 Configuration................................................................................................37
19. SOUND INTERFACE ............................................................................................. 38
19.1 Connector ....................................................................................................39
19.2 Configuration................................................................................................39

KONTRON
CMP/P3 and CMP/C3 User’s Guide Contents
3
20. FEATURE INTERFACE ......................................................................................... 40
20.1 Connector ....................................................................................................40
20.2 Configuration................................................................................................40
20.3 Signal Description..........................................................................................41
21. FAN INTERFACE................................................................................................... 43
21.1 Connector ....................................................................................................43
21.2 Configuration................................................................................................43
22. POWER INTERFACE............................................................................................. 44
22.1 Connector ....................................................................................................44
22.2 Configuration................................................................................................45
23. WATCHDOG TIMER .............................................................................................. 46
23.1 Configuration................................................................................................46
23.2 Programming ................................................................................................46
23.2.1. Initialization...........................................................................................46
23.2.2. Trigger...................................................................................................46
24. SYSTEM CONTROLLER ....................................................................................... 47
24.1 Connector ....................................................................................................47
24.2 Configuration................................................................................................47
25. APPENDIX A: SYSTEM-RESOURCE ALLOCATION ........................................... 48
25.1 Interrupt Request (IRQ) Lines...........................................................................48
25.2 Direct Memory Access (DMA) Channels ...............................................................48
25.3 Memory Map .................................................................................................49
25.3.1. Using Expanded Memory Managers ..............................................................50
25.4 I/O Address Map ............................................................................................51
25.5 Peripheral Component Interconnect (PCI) Devices................................................52
26. APPENDIX B: BIOS OPERATION......................................................................... 53
26.1 Determining the BIOS Version ..........................................................................53
26.2 Configuring the System BIOS............................................................................54
26.2.1. Start Phoenix BIOS Setup Utility..................................................................54
26.2.2. General Information .................................................................................54
26.3 Main Menu....................................................................................................56
26.4 Master or Slave Submenus ...............................................................................57
26.4.1. Memory Shadow Submenu..........................................................................58
26.4.2. Memory Cache Submenu ............................................................................58
26.4.3. Advanced Menu .......................................................................................59
26.4.4. Advanced Chipset Control Submenu .............................................................60
26.4.5. PCI Configuration Submenu........................................................................61
26.4.6. PCI/PNP ISA UMB Region Exclusion Submenu.................................................62
26.4.7. PCI/PNP ISA IRQ Resource Exclusion Submenu ...............................................62
26.4.8. Keyboard Features Submenu.......................................................................63
26.4.9. I/O Device Configuration Submenu ..............................................................64
26.4.10. Watchdog Settings Submenu ......................................................................65

KONTRON
Contents 4 CMP/P3 and CMP/C3 User’s Guide
26.4.11. Hardware Monitor Submenu .......................................................................65
26.4.12. Temperature Management Submenu ............................................................65
26.5 Security Menu ...............................................................................................66
26.6 Power Menu ..................................................................................................67
26.7 Boot Menu....................................................................................................68
26.7.1. Dark Boot ...............................................................................................68
26.8 MultiBoot 3 ..................................................................................................69
26.8.1. Boot First Submenu ..................................................................................71
26.9 Exit Menu .....................................................................................................71
26.10 Kontron BIOS Extensions.................................................................................72
26.10.1. JIDA BIOS extension.................................................................................72
26.10.2. LAN RPL ROM...........................................................................................72
26.11 Updating or Restoring BIOS Using PhoenixPhlash ................................................73
26.11.1. Flashing a BIOS........................................................................................73
26.11.2. Preventing Problems When Updating or Restoring BIOS ...................................74
27. APPENDIX C: BLOCK DIAGRAM......................................................................... 75
28. APPENDIX D: MECHANICAL DIMENSIONS ........................................................ 76
29. APPENDIX E: CONNECTOR LAYOUT ................................................................. 77
29.1 Connector Functions and Interface Cables...........................................................78
29.2 Pinout Table .................................................................................................79
30. APPENDIX F: PC ARCHITECTURE INFORMATION............................................ 81
30.1 Buses ..........................................................................................................81
30.1.1. PISA ......................................................................................................81
30.1.2. ISA, Standard PS/2 - Connectors .................................................................81
30.1.3. PCI ........................................................................................................81
30.2 General PC Architecture...................................................................................82
30.3 Ports ...........................................................................................................82
30.3.1. RS-232 Serial ..........................................................................................82
30.3.2. ATA .......................................................................................................83
30.3.3. USB.......................................................................................................83
30.4 Programming ................................................................................................83
31. APPENDIX G: DOCUMENT REVISION HISTORY................................................ 84

KONTRON
CMP/P3 and CMP/C3 User’s Guide User Information
1
1. USER INFORMATION
1.1 About This Manual
This document provides information about products from KONTRON Embedded Computers AG
and/or its subsidiaries. No warranty of suitability, purpose, or fitness is implied. While every
attempt has been made to ensure that the information in this document is accurate, the
information contained within is supplied “as-is” and is subject to change without notice.
For the circuits, descriptions and tables indicated, KONTRON assumes no responsibility as far as
patents or other rights of third parties are concerned.
1.2 Copyright Notice
Copyright © 2004 KONTRON Embedded Computers AG.
All rights reserved. No part of this manual may be reproduced, transmitted, transcribed, stored in a
retrieval system, or translated into any language or computer language, in any form or by any
means (electronic, mechanical, photocopying, recording, or otherwise), without the express
written permission of KONTRON.
JUMPtec Industrielle Computertechnik AG and KONTRON Embedded Computers AG merged in July
2002. JUMPtec is now known as KONTRON Embedded Modules GmbH. Products labeled and sold
under the KONTRON Embedded Modules name (formerly JUMPtec) are now considered KONTRON
products for all practical purposes, including warranty and support.
DIMM-PC®, PISA®, ETX Components SBC, JUMPtec®, and KONTRON Embedded Modules are
registered trademarks of KONTRON Embedded Modules GmbH©.

KONTRON
User Information 2 CMP/P3 and CMP/C3 User’s Guide
1.3 Trademarks
The following lists the trademarks of components used in this board.
!IBM, XT, AT, PS/2 and Personal System/2 are trademarks of International Business
Machines Corp.
!Microsoft is a registered trademark of Microsoft Corp.
!Intel is a registered trademark of Intel Corp.
!All other products and trademarks mentioned in this manual are trademarks of
their respective owners.
1.4 Standards
KONTRON Embedded Modules is certified to ISO 9000 standards.
1.5 Warranty
This KONTRON Embedded Modules product is warranted against defects in material and
workmanship for the warranty period from the date of shipment. During the warranty period,
KONTRON Embedded Modules will at its discretion decide to repair or replace defective products.
Within the warranty period, the repair of products is free of charge as long as warranty conditions
are observed.
The warranty does not apply to defects resulting from improper or inadequate maintenance or
handling by the buyer, unauthorized modification or misuse, operation outside of the product’s
environmental specifications or improper installation or maintenance.
KONTRON Embedded Modules will not be responsible for any defects or damages to other products
not supplied by KONTRON Embedded Modules that are caused by a faulty KONTRON Embedded
Modules product.

KONTRON
CMP/P3 and CMP/C3 User’s Guide User Information
3
1.6 Technical Support
Technicians and engineers from KONTRON Embedded Modules and/or its subsidiaries are available
for technical support. We are committed to making our product easy to use and will help you use our
products in your systems.
Before contacting KONTRON Embedded Modules technical support, please consult our Web site for
the latest product documentation, utilities, and drivers. If the information does not help solve the
problem, contact us by telephone.
Asia Europe North/South America
Kontron Embedded
Technology (Asia Pacific)
Kontron Embedded Modules GmbH Kontron America
Far East Science Park, 2nd
Floor No. 2, Lane 50, Nan
Kang Road Section 3, Nan
Kang District Taipei, Taiwan
Brunnwiesenstr. 16
94469 Deggendorf – Germany
6260 Sequence Drive
San Diego, CA 92121-4371
Tel: [phone] Tel: [phone] Tel: [phone]
Fax: [phone] Fax: [phone] Fax: [phone]

KONTRON
Introduction 4 CMP/P3 and CMP/C3 User’s Guide
2. INTRODUCTION
2.1 coolMONSTER/P3 and coolMONSTER/C3
coolMONSTER/P3 and coolMONSTER/C3 component SBC modules support the IntelMobile
PentiumIII with 256 KB and the IntelMobile Celeronlow voltage CPU with 128KB L2 cache
memory on die. The coolMONSTER/P3 and coolMONSTER/C3 integrate the complete functionality of
a PentiumIII class motherboard with CPU, System BIOS, up to 256MB or 512MB SDRAM, keyboard
controller, real-time clock, onboard VGA with LCD interface, and additional peripheral functions.
The coolMONSTER/P3 and coolMONSTER/C3 follow the PISA format, which provides the functionality
of a PCI and ISA bus on one well-defined bus. To connect a backplane with a PISA board, you need
an EISA-like, edge-card connector.
The pinout of the upper row of the PISA bus connector corresponds to the pinout of the ISA bus
connector. The lower row provides PCI signals, which makes it easy to design backplanes with up to
four PCI slots and additional ISA slots.
2.2 The coolMONSTER PISA® Family
coolMONSTER products represent the best scaleable half-size Slot SBC family. Each coolMONSTER
module is characterized by the same mechanical and electrical pinout for the Keyboard, COM A-D,
Sound, IrDA, EIDE 40pin and 44pin, LPT, LAN, VGA, USB, and Floppy. These homogeneous features
facilitate easier upgrades within the Kontron Embedded Modules GmbH coolMONSTER product
family.
PISA® is the proven space saving concept that provides full PCI and ISA bus signals on just half-size
Slot boards. The ancestors were full-sized PICMG boards that have PCI and ISA card edges in a row.
PISA squeezed them to just half-size, which still serves full PCI and ISA buses, which enabled
smaller and cheaper enclosures when possible while maintaining all PCI and ISA periphery.
Whenever a LCD panel is required, coolMONSTER products with onboard graphics controllers are the
right choice. Display connections are simplified when using these units, which come with a JUMPtec
Intelligent LVDS Interface (JILI) or JUMPtec Intelligent Display Adaption (JIPA). The interface can
recognize which display is connected and then independently set all video parameters.
As part of the standard features package, all coolMONSTER modules come with a JUMPtec
Intelligent Device Architecture (JIDA) interface, which is integrated into the BIOS of the SBC
modules. This interface enables hardware independent access to coolMONSTER features that cannot
be accessed via standard APIs. Functions such as watchdog timer, brightness and contrast of LCD
backlight and user bytes in the EEPROM can be configured with ease by taking advantage of this
standard coolMONSTER module feature.

KONTRON
CMP/P3 and CMP/C3 User’s Guide 5 Getting Started
3. GETTING STARTED
The easiest way to get the coolMONSTER/P3 or coolMONSTER/C3 board running is to use a PISA
baseboard from Kontron Embedded Modules GmbH. Take the following steps:
1. Turn off the power supply.
2. Connect the power supply to the baseboard or the coolMONSTER.
3. Plug a memory module into the memory socket of the coolMONSTER.
4. Plug the coolMONSTER to the PISA baseboard.
5. Connect the CRT monitor to the CRT interface or a LCD panel to the JILI interface by
using the corresponding adapter cable.
6. Plug the keyboard to the PS/2 keyboard connector and the mouse to the PS/2
mouse connector.
7. Connect the floppy drive cable to the coolMONSTER floppy interface. Attach the
floppy drive to the connector at the opposite end of the cable.
8. Connect the power supply to the floppy’s power connector.
9. Plug a hard-drive data cable to one of the coolMONSTER hard-disk interfaces.
Attach the hard disk to the connector at the opposite end of the cable.
10. If necessary, connect the power supply to the hard disk’s power connector.
11. Make sure all your connections have been made correctly.
12. Turn on power.
13. Enter the BIOS by pressing the F2 key during boot-up. Make all changes in the BIOS
setup. See the BIOS chapter of this manual for details.

KONTRON
Specifications 6 CMP/P3 and CMP/C3 User’s Guide
4. SPECIFICATIONS
4.1 Functional Specifications
!Processor
•IntelMobile PentiumIII processor with 256KB L2 cache memory on die
•IntelMobile Celeronlow voltage (LV) CPU with 128KB L2 cache memory on die
!Chipset
•IntelBX 440
or
•IntelGX 440 (only on boards equipped with the 850MHz processor)
!Power Supply
•5V only supply
•Onboard power supply to low voltage technology
!Memory
•One DIMM socket for up to 256Mbyte (BX 440 chipset) or 512Mbyte (GX 440 chipset)
unregistered SDRAM-DIMM module
•Supporting SDRAM PC100 and SDRAM PC133 with 100 MHz Speed
!Four Serial Ports (COM A, COM B, COM C and COM D)
•Three standard RS232C serial ports, 16550 compatible (COM A, COM B and COM C)
•One serial port as RS232 or RS485 (COM D)
•One serial port as RS232 or IrDA (COM B)
!Infrared Device Association (IrDA) Interface
!One Parallel Port (LPT1)
•Enhanced Parallel Port (EPP) and Extended Capabilities Port (ECP) with bi-directional
capability
!Floppy Interface
!System Monitor Controller for Temperature and Fan
!Enhanced Intelligent Drive Electronics (EIDE)
•Two UDMA PCI Bus Master EIDE ports (up to 4 IDE Devices)
!Universal Serial Bus (USB)
•Two USB 1.0 ports (UHCI)
•USB legacy keyboard and mouse support

KONTRON
CMP/P3 and CMP/C3 User’s Guide 7 Specifications
!Ethernet
•Intel82559ER 10/100 Mbps PCI Fast Ethernet controller
!Onboard Video Graphics Array (VGA)
•ATI RAGEMobility-M LCD-VGA Controller with integrated 4MB Video RAM
or
•ATI RAGEMobility-M1 LCD-VGA Controller with integrated 8MB Video RAM
(only on boards with 700MHz or 850MHz processor)
•Cathode ray tube (CRT) and low voltage differential signaling (LVDS)
LCD/flat-panel interfaces
!Onboard Sound PCI AudiodriveSolution
•ESS Solo-1(ES1938S)
!Phoenix BIOS, 256KB Flash BIOS
!NV-EEPROM for CMOS Setup Retention without Battery
!PS/2 Keyboard Controller
!PS/2 Mouse Controller
!Watchdog timer (WDT)
!Real-time Clock with Onboard Battery Supply

KONTRON
Specifications 8 CMP/P3 and CMP/C3 User’s Guide
4.2 Mechanical Specifications
!PISA Bus Connector
•Edge card connector, EISA standard, AMP 650226-1 (or compatible)
!Dimensions
•Length x Width: 176 mm x 125mm (6.9” x 4.9”)
!Height on Top
•Maximum 60 mm (2.36”) on 850MHz version
•Ca. 40mm (1.58”) on all other versions
•Height is depending upon SDRAM module and CPU cooler/fan. This can block PCI or
ISA slots on some backplanes.
!Height on Bottom
•Maximum 6.5 mm (0.25”)
!Weight
•346g (full featured maximum performance version without SDRAM)
4.3 Electrical Specifications
4.3.1. Supply Voltage
!5V DC +/- 5%
4.3.2. Supply Voltage Ripple
!100 mV peak to peak 0 - 20 MHz
4.3.3. Supply Current (typical)
Power-consumption tests were executed during the DOS prompt and with 100% CPU load. The
tested boards were equipped with 256MB SDRAM.
CPU Fan Graphic DOS Prompt 100% CPU load
Celeron 300 MHz no 4MB ATI Rage Mobility 1.93A 2.07A
PIII 400 MHz mobile yes 4MB ATI Rage Mobility 2.67A 2.92A
PIII 700 MHz mobile yes 8MB ATI Rage Mobility 3.59A 4.00A
PIII 850 MHz mobile yes 8MB ATI Rage Mobility 5.32A 6.27A

KONTRON
CMP/P3 and CMP/C3 User’s Guide 9 Specifications
4.3.4. Supply Current (maximum)
CPU Graphic Current
Celeron 300 MHz 4MB ATI Rage Mobility TO BE DONE
PIII 400 MHz mobile 4MB ATI Rage Mobility TO BE DONE
PIII 700 MHz mobile 8MB ATI Rage Mobility TO BE DONE
PIII 850 MHz mobile 8MB ATI Rage Mobility TO BE DONE
(calculated theoretical values from all components maximum supply currents)
4.3.5. Real-time Clock (RTC) Battery
!Voltage range: 3.0V-4.2V
!Max current: 10µA
English:
CAUTION ! Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type recommended by the manufacturer. Dispose of used
batteries according to the manufacturer's instructions.
Deutsch:
VORSICHT ! Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz
nur durchden selben oder einen vom Hersteller empfohlenen gleichwertigen Typ.
Entsorgung gebrauchter Batterien nach Angaben des Herstellers.
French:
ATTENTION ! Risque d'explosion avec l'échange inadéquat de la batterie.
Remplacement seulement par le même ou un type équivalent recommandé par le
producteur. L'évacuation des batteries usagées conformément à des indications du
fabricant.
Danish:
ADVARSEL ! Lithiumbatteri – Eksplosionsfare ved fejlagtig Håndtering. Udskifting
må kun skemed batteri af samme fabrikant og type. Lever det brugte batteri tilbage til
leverand∅ren.
Finnish:
VAROITUS ! Paristo voi rãjãhtãã, jos se on virheellisesti asennettu. Vaihda paristo
ainoastaan laltevalmistajan suosittelmaan tyyppiln. Havita kaytetty paristo
valmistajan ohjeiden mukaisesti.
Spanish:
Precaución ! Peligro de explosión si la batería se sustituye incorrectamente.
Sustituya solamente por el mismo o tipo equivalente recomendado por el fabricante.
Disponga las baterías usadas según las instrucciones del fabricante.
The battery of this product is not considered to be accessible by the end user. Safety
instructions are given only in English, German, French, Danish, Finish and Spanish. If the
battery is accessible by the end user, it is in the responsibility of the customer to give the
corresponding safety instructions in the required language(s).

KONTRON
Specifications 10 CMP/P3 and CMP/C3 User’s Guide
4.4 MTBF
The following MTBF (Mean Time Between Failure) values were calculated using a combination of
manufacturer’s test data, if the data was available, and a Bellcore calculation for the remaining
parts. The Bellcore calculation used is “Method 1 Case 1”. Using this method, components are
assumed to be operating at a 50% stress level in a 40° C ambient environment and the system is
assumed to have not been burned in. Manufacturer’s data has been used wherever possible. The
manufacturer’s data, when used, is specified at 50° C, so in that sense the following results are
slightly conservative. The MTBF values shown below are for a 40° C office or telecommunications
environment. Higher temperatures and other environmental stresses such as extreme altitude,
vibration, and salt-water exposure will lower the MTBF values.
!System MTBF (hours) : 123.388 for coolMONSTER/P3 400MHz
Notes: Fans usually shipped with Kontron Embedded Modules GmbH products have
50,000-hour typical operating life. The above estimates assume no fan, but a
passive heat sinking arrangement.
Estimated RTC battery life (as opposed to battery failures) is not accounted for in
the above figures and needs to be considered separately. Battery life depends on
both temperature and operating conditions. When the Kontron unit has external
power; battery drain occurs from leakage paths.
4.5 Environmental Specifications
4.5.1. Temperature
The IntelMobile PentiumIII processor and the IntelMobile Celeronlow voltage (LV) CPU
are specified for proper operation when the junction temperature is within the specified range of
0°C to 100°C. The system controller can measure the temperature.
!Operating: 0 to +70°C (*) (with appropriate airflow)
0 to + 60°C (*) (with appropriate airflow) for 850MHz version
!Non-operating: -10 to +85 °C (noncondensing)
Note:
The maximum operating temperature is the maximum measurable temperature on any
spot on the module’s surface. You must maintain the temperature according to the above
specification.

KONTRON
CMP/P3 and CMP/C3 User’s Guide 11 Specifications
For devices that are specified for higher case temperatures, please see the following table.
Device Function Max. Case Temperature
Intel82443BX Chipset (Host Bridge) +105°C
ATIRageTM Mobility Graphic Controller +85°C
LT1702 DC/DC Converter +70°C
LT1702 (on 850MHz) DC/DC Converter (ext.- Temp) +85°C
MOSFETs Transistors +85°C
4.5.2. Humidity
!Operating: 10% to 90% (noncondensing)
!Nonoperating: 5% to 95% (noncondensing)

KONTRON
CPU, Chipset and Super-I/O 12 CMP/P3 and CMP/C3 User’s Guide
5. CPU, CHIPSET, AND SUPER I/O
5.1 CPU
The central processing unit (CPU) consists of either a:
!IntelMobile PentiumIII processor with 256KB L2 cache memory on die.
!IntelMobile Celeronlow voltage CPU with 128KB L2 cache memory on die.
5.2 Chipset
The coolMONSTER/P3 and coolMONSTER/C3 PISA Boards operate with the Intel ® 440BX AGPset,
which consists of the 82443BX Host Bridge and the 82371EB PIIX4E. The 850MHz version of the
coolMONSTER/P3 comes with the 82443GX Host Bridge. The chipset provides the following
features:
!82443BX/GX Host Bridge Controller
!82371EB PCI ISA IDE Accelerator (PIIX4E)
!Full Support for up to Mobile Pentium III /Celeron LV processors,
with system bus frequencies of 100 MHz
!100 MHz SDRAM Memory Interface
!PCI Add-in Slots, PCI Specification Rev 2.1 Compliant
!1 AGP Slot, AGP Interface Specification Rev 1.0 Compliant,
AGP 66/133 MHz, 3.3V device support
!Integrated IDE Controller with Ultra DMA/33 support, PIO Mode 4 transfer,
PCI IDE Bus Master support
!Integrated Universal Serial Bus (USB) UHCI Controller
with 2 USB ports; USB 1.0 compliant
!Integrated System Power Management Support
!ISA add-in slots

KONTRON
CMP/P3 and CMP/C3 User’s Guide 13 CPU, Chipset, and Super I/O
5.3 Super I/O
There are two super I/O devices onboard of the coolMONSTER/P3 and coolMONSTER/C3. The first
one is the Winbond W83977EF and provides the following features:
!Keyboard controller
!PS/2 Mouse interface
!Two serial interface (COM A and COM B)
!Parallel interface (LPT)
!Floppy Disk Drive controller
!IrDA interface
An additional SMsC FD37C669 offers two more serial interfaces (COM C and COM D).

KONTRON
Video Controller 14 CMP/P3 and CMP/C3 User’s Guide
6. VIDEO CONTROLLER
The COOLMONSTER/P3 and COOLMONSTER/C3 use the ATI RAGEMobility-M LCD-VGA Controller with
4MB integrated video memory. The 700MHz and 850MHz versions of this board come with the ATI
RAGEMobility-M1 LCD-VGA-Controller with 8MB of integrated video memory. The controller
features:
!Motion Compensation for full frame rate software DVD playback
!Resolution up to 1600x1200 (CRT) and 1280x1024 (TFT) respectively
!Application-proven 2D and 3D acceleration
!Dual-View for simultaneous and independent LCD and CRT outputs
!Integrated dual channel 110MHz LVDS transmitter
!Innovative ratiometric expansion enables source images to fit any panel resolution
up to 1280x1024
!Support for every major OS and environment
6.1 Video Subsystem Block Diagram