Konvision KFM-5X series User manual

V3.3.4
Konvision Monitor USER MANUAL
KFM-5X / 6X series LCD Monitors
www.k o n v i s i o n .c o m
www.konvision.com

1
Catalogue
1
Notes............................................... 2
Notes 2
Security .......................................... 2
Screen Maintenance .................. 2
Cabinet Maintenance ................. 2
Installation .................................. 3
Rack mount Installation .............. 3
Transportation ............................ 3
The following does not belong to
failures:....................................... 3
Features.......................................... 3
High Brightness LCD Panel........ 3
High Brightness Tally Indicator ... 3
Auto-detection of all color system
(PAL, NTSC, SECAM)................ 3
3D Video Decoder ...................... 3
Motion-Adaptive Interlace to ...... 3
Progressive ................................ 3
10BIT Signal Processing ............ 4
Support Multiformat SDI Signals 4
Y/C Input .................................... 4
SDI Input .................................... 4
YPbPr Input ................................ 4
HDMI/DVI/VGA Input.................. 4
Signal Source Loop Through...... 4
PIP/PBP ..................................... 4
SWAP Function .......................... 4
Color Temperature...................... 4
Image Size Setting ..................... 4
Marker Setting ............................ 4
HV Delay .................................... 4
Color Space ............................... 4
Color Calibration......................... 4
Scan Mode ................................. 5
Part Zoom In............................... 5
Audio level meter (UV+PPM) ..... 5
Waveform ................................... 5
Focus Assist ............................... 5
False Color ................................. 5
Histogram ................................... 5
Vector scope............................... 5
Over exposure............................ 5
Pixel Measurement..................... 5
Timecode.................................... 5
Remote Control Function ........... 5
Parts and Functions...................... 6
Front View .................................. 6
Rear View................................... 8
KFM-1753W rear view port: .....8
KFM-1760D rear view port: ......8
OSD Menu ...................................... 9
Menu Operation.......................... 9
Menu Item Description ............... 9
Main Menu: ................................9
Sub Menu:..................................10
Status: .......................................10
Function Key: ............................10
Picture: .......................................11
Image: ........................................11
Audio: .........................................12
Marker:.......................................13
Scope: .......................................14
Embedded code: .......................15
Layout: .......................................15
IMD:............................................17
Alarm:.........................................18
Setup:.........................................18
Key Lock: ...................................19
3. Function Key..........................19
Function Key Menu Operation
Instructions.................................... 19
Dual picture operation .................. 20
Pixel Measurements Operating
Instructions.................................... 20
SDI 2K Signal Display Description20
Factory Reset................................. 20
Remote Control.............................. 21
Rack quick installation process... 21
Note................................................. 23
About This Manual
The instructions in this manual are for KFM-5X/6X series LCD Monitors .
The following description uses model KFM-1753W&KFM-1760D pictures.
Please conrm the model number of the device before reading this manual.

Security
Screen Maintenance
Cabinet Maintenance
Please follow the below guidelines carefully to
prevent discoloration, stains and scratches on
the screen:
Please follow the guidelines below to prevent
potential damage.
Screen may be cleaned by gently wiping with lint
free cloth to remove dust. For the more difficult
cleaning, use lint free cloth that has been very lightly
dampened with detergent, then dry any excess
moisture from the monitor or LCD panel immediately
to prevent damage.
·Avoid striking the screen with any object.
·Do not wipe the screen hard.
·Do not wipe the screen with solvents such as
alcohol, thinner or gasoline.
·Do not spray detergent or other cleaners on
the monitor or LCD panel, as it may cause
fault because of water droplets into the monitor.
·Do not write on the screen.
·Do not paste or stick any viscous markers on
the screen.
·Do not wipe the cabinet with solvents such
as alcohol, thinner or gasoline.
·Do not use any pesticides and/or other
volatile substances.
·Do not allow prolonged contact with rubber
or plastic.
·Do not wipe the cabinet hard. Use a soft, lint
free cloth to clean. If the cabinet cleaning is
more di󰀩cult, use lint free cloth that has
been very lightly dampened with detergent
and then dry it to wipe.
Notes
Notes
For the safety use of products, please read the
following instructions regarding the installation, use
and maintenance carefully.
·Please read the product safety and operating
instructions carefully before the product is operated.
·Please keep the safety and operating instructions
for future reference.
·Please pay strict attention to the warnings and
implement the products according to the
operating instructions closely.
·All operating instructions should be strictly
enforced.
1. Please use the power cord recommended
by the manufacturer.
2. Please do not place heavy objects on the
power cord.
3. Please do not expose the monitors to rain,
humid, dusty places.
4. Please do not place vessels with liquid
(such as cups, beverage bottles) on the
monitor.
5. Please do not place this product in high
heat places.
6. Please make sure the earth terminal is
good in order to avoid electric shock.
7. Please do not open the back cover to avoid
electric shock. Please contact professionals
for service needs.
8. If there is no image or sound, please unplug
the power cord from the AC outlet immediately.
Please consult professionals if problem still exists
after examining carefully.
9. Do not place this product at unstable places
such as cars, shelves or tables, as it is easy to
make the product fall down, may cause
severe hurt to children and adults and
damage to the product.
10. Please do not touch the power plug with
wet hands, as it will cause electric shock.
11. Please do not expose the LCD panel in direct
sunlight for a long time, it will result in damage
or aging of the LCD panel.
12. Please display this product at a suitable
temperature and humidity.
13. Please do not spray any liquid things
and/or add any objects into the monitor,
it might cause voltage instability and
short-circuit, also can easily cause res
and blackouts.
14. If do not use the device for a long time,
please unplug the power cord from the
AC outlet.
15. Please keep not less than 5cm space
around the vents while using the monitor,
in order to obtain a good heat dissipation
e󰀨ect.
Installation
·Keep adequate air circulation to prevent
device internal overheating. Please do not
place the product on the surface of some
certain objects (such as blankets, carpets,etc.),
as these objects may block the vents.
·Please keep the device away from heat
generating sources, such as radiator, heaters
and air duct, also keep it away from much
dust or mechanical vibration.
Rack mount Installation
Transportation
The following does not belong to
failures:
For rack mount installation, please keep 1U space
from both top and bottom to make sure, adequate
air circulation, or install an external electric fan.
Please follow the instructions and install with the rack
mounts provided by the manufacturer.
This monitor is precise equipment and needs
professional packing materials to transport.
Please do not use packing materials provided by
suppliers except KONVISION or its authorized
packing material suppliers.
When the following situations occur, please
turn o󰀨 the power, do not insert the plug and
contact a professional service staff to deal
with it in a timely manner.
1. This product smells of smoke and o󰀨-avor.
2. When this product displays abnormal operating
conditions, such as there is no picture or sound.
3. When any liquid is splashed into the product
or product dropped.
4. When the product soaked or fell into the water.
5. When the product has been damaged or under
other easy to get damaged circumstances.
6. When the power cord or plug is damaged.
1. If the static image displayed too long, it will
have residual image, which should be attributed
to the characteristics of LCD display but not
a failure. Residual image will disappear
automatically after a period of time.
2. If this device is used in a cold environment,
the screen may appear a burn-in image.
This is not a product failure, when the
monitor temperature changes, screen
will return to normal conditions.
3. LCD screen may appear tiny spots
(red, blue or green), this is not a fault,
LCD screens are manufactured with high
precision technology, and a small
number of pixels may not be able to show
intermittent.
4. Screen and cabinet will become warm
gradually during operating.
Features
High Brightness LCD Panel
High Brightness Tally Indicator
3D Video Decoder
Motion-Adaptive Interlace to
Progressive
Auto-detection of all color system
(PAL, NTSC, SECAM)
- High brightness, high contrast, high-speed
response and wide viewing angle technology
makes the monitor can be used under variety
of lighting conditions.
- The tally function via GPI or LAN port, with two
colors red and green.
- Process 3D decoding on VIDEO signals, to
realize better reduce cross color.
- It converts interlaced video to progressive video
by motion detection, reduce the serrated
image.
- This unit detects the color system automatically.
32

YPbPr Input
HDMI/DVI/VGA Input
Signal Source Loop Through
Image Size Setting
Marker Setting
HV Delay
Color Space
Color Calibration
PIP/PBP
Support Multiformat SDI Signals
Y/C Input
SWAP Function
Color Temperature
SDI Input
10BIT Signal Processing
- YPbPr video signal (Compatible YCbCr) can
be input through this connector.
- HDMI signal can be input via HDMI to DVI-I
convertor through DVI connector, DVI signal
can be input through DVI connector, VGA
signal can be input via VGA to DVI-I convertor
through DVI connector.
- Signal that linked to the input connector will be
enlarged and linked to output connector.
SDI reclock loop out ensure the signal without
enervation.
- The display mode is switchable among 16:9,
4:3, full screen, 1:1, and the original image
proportion.
- Show frame borders, center marker, and safety
area, etc.
- Display horizontal and vertical blanking area of
SDI input signal.
- Color space include: Rec 709, EBU, DCI P3
D65, DCI P3, Rec2020, USER. (This function
only available to KVM-6X series)
- This enable to calibrate imported color data of
the image being measured by color analyzer.
(This function only available to KVM-6X series,
specic instructions please contact with the
dealer.)
- Two SDI inputs signals display simultaneously
under PIP (picture in picture) and PBP(picture
by picture) mode. One SDI input signal can
be also displayed with another signal of
VIDEO, S-VIDEO, COMPONENT, HDMI
simultaneously, and showing two pictures on
the screen.
- The SDI interface supports SD-SDI, HD-SDI,
dual link HD-SDI and 3G SDI inputs.
- Decomposition for the luminance signal (Y) and
chrominance signals (C) of the video signal
can be input through this connector.
- In PIP/PBP mode, two pictures can be swapped
between each other.
- Di󰀨erent color temperatures can be selected freely.
- Support multi-format SDI input, SD-SDI, HD-SDI,
3G SDI.
- Support SMPTE425M-A/B 4:4:4 signals.
- Signal input, signal processing and image
output are 10bit data processing, to ensure the
details display of the image.
Scan Mode
- Scan mode includes Full Scan, Over Scan,
Under Scan. Full scan displays the content of
all areas of the input signal. Over scan displays
105% of the area of the input signal. Under
scan displays 95% of the area of the input
signal.
Vector scope
- Vector UV analysis for color bar signal input.
Part Zoom In
- Zoom in any part of the picture, to watch picture
details more clearly, and assist for focus.
Audio level meter (UV+PPM)
- Display the audio level meter (UV+PPM) for
SDI embedded audio.
Waveform
- Display input signal waveform and color
scope for SDI signal input monitoring.
It includes luminance waveform, CbCr
waveform. Luminance waveform will mark
with red if over the value specied by user.
Over exposure
- Over exposure is to aid the cameraman
accurately control the lighting to avoid over
exposure by marking the brightness exceeds
the user-specied range (95% by default)
with the form of covering zebra pattern.
Pixel Measurement
- User can measure any pixel’s specic
position and RGB value, also can compare
the YRGB value between any 2 pixels.
Timecode
- Display SMPTE timecode (LTC, VITC1,
VITC2) under SDI input, it is used for
identifying and synchronizing of video data
streams.
Remote Control Function
- Available to connect to the remote terminal to
operate the equipment directly, select
the input signal, longitudinal mode settings
and tally indicator, etc.
Focus Assist
- Focus assist is to aid the cameraman focus
on the main body by marking the
sharpest edge of the image with red.
False Color
- False color can Intuitively observe and
calculate illumination level in the image,
luminance and illumination values display
mapping as luminance level, from darkest
to brightest, display blue, cyan, green, yellow,
orange and red in turn.
Histogram
- YRGB histogram displays the hue distribution
of the entire image under SDI input condition,
can intuitively display exposure of the image,
display R, G, B 3 channels independently.
54

Parts and Functions
Front View
Tally Indicator
Speaker
SDI1 Button and Indicator
Power Button and Indicator
Control method of Tally light.
1. GPI port(control method: please look the GPI port
description).
2. RS422 Port: support use TSL3.1 or TSL 4.0 protocol
control the tally light.
Stereo audio output.
Press this button to select SDI1 signal input, indicator
turns blue.
When the external AC power supply with electricity,
the indicator light is red. Press this POWER button to
power on the monitor, and the indicator light turns blue.
Press this button for about 2 seconds, can turn o󰀨 the
monitor, the indicator light turn red.
1
2
4
SDI2 Button and Indicator
Press this button to select SDI2 signal input, indicator
turns blue.
5
ANALOG Button and Indicator Light
HDMI/VGA Button and Indicator Light
F1-F5 Button and Indicator Light
Press this button to select input signal between YPbPr,
Video, S-video, indicator turns blue.
Press this button to select signal input among DVI/
HDMI/VGA, indicator turns blue.
F1-F5 these buttons can be used as shortcut buttons.
Press the F1-F5 buttons to select the corresponding
function.
When the set button function item is set to o󰀨 in the
main menu, those buttons are invalid.
F1-F5 These button functions can be set in the menu
Function key options.
6
7
8
3
1
2 23 4 5 6 7 8 9 10 11 12 13 14 15
PIP/PBP Button
MENU Button
DOWN/WIN SEL Button
LEFT Button
RIGHT/VOLUME Button
UP/IMAGE ADJ Button
Press this button for window layout among single, PIP,
PBP mode. In PIP/PBP mode, one of the signals must
be SDI1 input, the other can be any of SDI2, HDMI,
PC, Video, YPbPr, etc.
Press this button to display the OSD menu, and press
it again to exit the menu.
Clear the Marker display.
Clear Display mode.
Turn o󰀨 the shortcut menu.
When entering the menu operation, press to select the
menu item.
When the screen is in the PIP / PBP state, press this
button to select one of the picture. In this case, you
can press other buttons to set the parameters of the
selected screen independently, without a󰀨ecting the
parameters of the other screen.
When entering the menu operation, press this button to
select the menu item.
When not in the menu operation, press this button to
enter the volume adjustment shortcut menu.
When entering the shortcut menu, press this key to
adjust the scroll bar to the left.
When entering the main menu operation, press this
button to select the sub menu to the right.
When entering the sub menu operation, press this
button to adjust the parameters of the current sub
menu item to the right.
When not in the menu operation, press this button to
enter the volume adjustment shortcut menu.
When entering the shortcut menu, press this button to
adjust the scroll bar to the right.
When in OSD main menu, press this button to select
up sub-menus.
When not in OSD menu, press this button to show
backlight, brightness, and contrast respectively.
The display has the following changes:
Backlight: The screen backlight brightness adjustment
shortcut menu display, press the LEFT button or
(RIGHT / VOLUME) button to adjust the brightness of
the screen backlight.
Brightness: The image brightness adjustment shortcut
menu is displayed. Press the LEFT button or the
(RIGHT / VOLUME) button again to adjust the image
brightness.
Contrast: The image contrast adjustment shortcut
menu is displayed. Press the LEFT button or the
(RIGHT / VOLUME) button again to adjust the image
contrast.
9
ZOOM/WIN SEL Button
At single mode: press this button to zoom in
At PIP/PBP mode: press this button to swap 2
windows rapidly.
10
11
13
14
15
12
76

Rear View
DC 12V IN
ON/OFF
12V DC power supply.
Power button.
1
2
The interface pins are dened as:
Pin 1: Ground
Pin 2: NC
Pin 3: NC
Pin 4: +12V
KFM-1753W rear view port:
KFM-1760D rear view port:
1
2
9 8 7 6 5 4 3
10
11 10
1 9 8 7 6 5 4 3
Menu Item Description
1. Main Menu:
Main menu Menu item
Status 1
Function Key 1
Picture 1
Image 1
Audio 1
Marker 1
Scope 1
Embedded code 1
Layout 1
IMD 1
Alarm 1
Setup 1
Key Lock 1
98
LAN
In shortcut functions: Turn the knob to adjust the value
of Brightness, Contrast and Chroma respectively.
Ethernet port for remote network control. Thought this
port, along with software “Konvision Device Controller”,
you can achieve remote controlling to the monitor
easily. (remote control software & instructions please
contact with the dealer)
3
GPI
GPI interface:
4
Diagram Pin GPI Signal Description
1 GPI1
when connect GND, GPI1 works,
GPI1 function can be set in the
menu function option.
2 GPI2
when connect GND, GPI2 works,
GPI2 function can be set in the
menu function option.
3 GPI3
when connect GND, GPI3 works,
GPI3 function can be set in the
menu function option
4 TX
RS232-TX, for MCU program
upgrade, please contact the dealer
for upgrade operation.
When the program is not upgraded,
the suspension is not connected.
5 RX
RS232-RX, for MCU program
upgrade, please contact the dealer
for upgrade operation.
When the program is not upgraded,
the suspension is not connected.
6 GPI4
when connect GND, GPI4 works,
GPI4 function can be set in the
menu function option
7 NC Not connect
8 GND Ground
RS422 IN and RS422 OUT
RS422 input and output interfaces. RS422 use TSL3.1
or TSL4.0 protocol to control. According to the protocol,
it can realize UMD and Tally control.
5
Diagram Pin RS422 IN Signal name RS422 OUT Signal name
1 GND GND
2 GND GND
3 Tx- Tx-
4 Rx+ Rx+
5 Rx- Rx-
6 Tx+ Tx+
7 NC NC
8 NC NC
HDMI/DVI/VGA
SDI1 IN/OUT
SDI2 IN/OUT
AUDIO(IN/OUT)
AC Faucet
VIDEO
DVI input, support DVI signal, HDMI signal (via
HDMI-DVI convertor), and VGA signal (via VGA-DVI
convertor)
SDI1 inputs (3G/HD/SD-SDI auto detect), SDI Reclock
loop through output, without enervation.
SDI2 inputs (3G/HD/SD-SDI auto detect), SDI Reclock
loop through output, without enervation.
Audio in used for analog signal input, Audio out used
for monitoring with 3.5mm earphone.
Using for AC power connect.
Video signals input.
7
8
9
10
11
6
OSD Menu
1. MENU Button:
Press the Menu button, the main menu will be
displayed on the screen, and press the MENU button
again to exit the menu.
When in sub-menu, press the MENU button to return
to previous menu.
When in setting option, press the MENU button to
return to exit.
2. IMAGEADJ(UP/DOWN) Knob:
When in the main menu or sub menu, the menu item
can be selected by pressing the UP / DOWN button to
select up / down functions.
3. VOLUME(LETF/RIGHT) Knob:
When in the main menu, enter the sub menu by
pressing RIGHT button.
When in the sub menu, the parameters can be
adjusted by pressing the LETF / RIGH function button.
Menu Operation

Function Key:
Sub Menu Description
F1 The Function keys can be set to the
following functions: Image Size, No
Denition, static frame, Time Code
Display, Audio Level Meter, Audio
Phase, Waveform Mode, Vector,
Focus Assist, Pixel Measurement,
False Color, Zebra, Histogram,
Picture Flip, Fast Mode, Blue Mode,
Gray Mode, Marker Setting.
(Note: Black stretch: When the
function key is set to black stretch,
press the function key to increase
the brightness of the low-brightness
part of the screen.)
F2 Same as above
F3 Same as above
F4 Same as above
F5 Same as above
GPI1 Can be set to the following functions:
Blue Mode, Image Size, Marker
Display, No Denition, Red TALLY,
Green TALLY, SDI1, SDI2, HDMI,
DVI, VGA, YPbPr, Video, S-Video.
GPI2 Same as above
GPI3 Same as above
GPI4 Same as above
2. Sub Menu:
Status:
Sub Menu Description
Source & Format Current window input signal and
resolution.
Fh The line frequency of the current
window input signal.
Fv The eld frequency of the current
window input signal.
Color Temp The current color temperature.
Color Space The current color space.
Image Size The image size of the current
window input signal.
Scan Mode The signal scan mode of the current
window input signal.
Screen Saver System screen saver status.
Power Saving System power saving mode status.
MCU Firmwave
Version
CPU software version
DSP Firmwave
Version
DSP software version
10 11
Picture:
Image:
Sub Menu Description
Backlight Backlight Adjustment.
· 0-100
Data Levels [Limit (64-940)]Select Limit (64-
940), video level.[Extend (64-1023)]
Select Extend (64-1023), ultra-white.
[Full (0-1023)]Select Full (0-1023),
full data level.[Custom]Custom is
for user denition.
· Limit (64-940)
· Extend (64-1023)
· Full (0-1023)
· Custom
Brightness Brightness Adjustment.
· 0-100
Contrast Contrast Adjustment.
· 0-100
Sharpness Sharpness Adjustment.
· 0-15
Colour Saturation Adjustment.
· 0-100
Hue Color Adjustment..
· 0-100
Sub Menu Description
Image Size [FILL ASPECT]Original ratio of the
signal source.[Full Screen]Full
screen image. [1: 1]At 1:1 pixel-to-
pixel display. It is invalid in PIP sub-
screen and PBP mode. [16: 9]16:9
aspect ratio. [4: 3]4:3 aspect ratio.
· FILL ASPECT
· Full Screen
· 1: 1
· 16: 9
· 4: 3
Scan Mode [100% Scan]100% Image display.
[Over Scan 5%]105% Image
display. [Under Scan 5%]95%
image display.
· 100% Scan
· Over Scan 5%
· Under Scan 5%
Sub Menu Description
Colour Temp Three modes of the xed color .
temperatures selection (5600K,
6500K, 9300K) and a custom
selection.
"Custom" is for user denition, to
adjust the gain value and o󰀨set
value of Red, Green and Blue. It will
save the color temperature setting
automatically.
· 5600K
· 6500K
· 9300K
Custom:
Red Gain 0-255
Green Gain 0-255
Blue Gain 0-255
Red o󰀨set 0-255
Green o󰀨set 0-255
Blue o󰀨set 0-255

Sub Menu Description
Part Zoom in Zoom in any part of the picture, to
watch picture details more clearly,
and assist for focus.
· <Right>Enter, <PIP>Part Zoom in
Gray Mode Monochrome mode with black and
white image.
· On
· O󰀨
Blue Mode Display in Blue only.
· On
· O󰀨
Fast Mode Interlace scan without converting
into progressive scan.
· On
· O󰀨
H/V Delay Display horizontal & vertical blanking
area of SDI input signal.
· On
· O󰀨
Gamma Mode Users can choose di󰀨erent Gamma
or turn it o󰀨 (this function only
available to KVM-6X series)
· Turn o󰀨
· Gamma 2.0
· Gamma 2.2
· Gamma 2.4
· Gamma 2.6
· Rec.2100 HLG 1.0
· Rec.2100 HLG 1.1
· Rec.2100 HLG 1.2
· Rec.2100 HLG 1.3
· Rec.2100 HLG 1.4
· Rec.2100 HLG 1.5
· ST2084 PQ
· S-Log3 (HDR)
· Slog (SDR)
· Slog2 (SDR)
· Slog3 (SDR)
Sub Menu Description
Color Space [Bypass]Color Space Choose
Bypass. [Rec 709]Color Space
Choose Rec709. [EBU]Color Space
Choose EBU. [DCI P3 D65]Color
Space Choose DCI P3 D65. [DCI
P3]Color Space Choose DCI P3.
[Rec2020]Color Space Choose
Rec2020. [USER1]Color Space
Choose User1. [USER2]Color
Space Choose User2.
· Bypass
· Rec 709
· EBU
· DCI P3 D65
· DCI P3
· Rec2020
· USER1
· USER2
Remark:
1. KVM-5X series only support
Rec709 and Bypass.
2. User1 and user2 option, support
user loads their own LUT table, store
in there, specic instructions please
contactwith the dealer.
Start Color Correction In the menu of Color calibration,
press right key to start color
calibration, must connect with color
analyzer to start color calibration.
Notice: restart the monitor to back
from color calibration function when
misled to the function.
· <Right> to start color Correction
Audio:
Sub Menu Description
Volume Speaker volume adjustment.
· 0-100
1312
Sub Menu Description
Headphone Volume Headphone volume adjustment.
· 0-100
Audio Out Mode [Normal]Right Channel MuteLeft
and right channel out normal.
[Left Channel Mute]Left channel
mute, just out the right channel.
[Right Channel Mute]Right channel
mute, just out the left channel.
· Normal
· Left Channel Mute
· Right Channel Mute
Remark:
Only for SDI and HDMI/DVI signal.
Audio Out Channel When in SDI Signal:
SDI embedded audio select in
CH1&CH2, CH3&CH4, CH5&CH6,
CH7&CH8.
When in HDMI Signal:
HDMI embedded audio selects in
CH1&CH2.
· CH1&CH2
· CH3&CH4
· CH5&CH6
· CH7&CH8
Remark:
Only for SDI and HDMI/DVI signal.
Headphone Volume Turn on/o󰀨 audio level meter display.
· On
· O󰀨
Remark:
Only for SDI and HDMI/DVI signal.
Audio Display
Channels
When in SDI Signal:
1-4 channels: 1-4 channels are
displayed horizontally or vertically on
the left side of the screen.
1-8 channels: 1-8 channels are
displayed horizontally or vertically on
the left side of the screen.
1-16 channels: 1-8 channels are
displayed horizontally or vertically on
the left side of the screen.
9-16 channels are displayed
horizontally or vertically on the left
side of the screen.
When in HDMI Signal:
Only displayed 1-2 channel
horizontally or vertically on the left
side of the screen.1-4 Channel
· 1-8 Channel
· 1-16 Channel
· 9-16 Channel
· 1-2 Channel
Remark:
Only for SDI and HDMI/DVI signal.
Sub Menu Description
Audio Display Mode [Horizontal]Audio level meter
display.[Vertical]horizontal/vertical.
· Horizontal
· Vertical
Remark:
Only for SDI/HDMI/DVI signal.
Audio Phase Meter Turn on/o󰀨 Audio Phase Meter
display.
· ON
· OFF
Remark:
Only for SDI/HDMI/DVI signal.
Audio Phase Channel When in SDI Signal:
SDI Audio Phase Channel can be
selected in CH1&CH2, CH3&CH4,
CH5&CH6, CH7&CH8.
When in HDMI Signal:
HDMI Audio Phase Channel only
can be selected in CH1&CH2.
· CH1&CH2
· CH3&CH4
· CH5&CH6
· CH7&CH8
Remark:
only for SDI and HDMI/DVI signal.
Audio Phase Channel Turn on/o󰀨 audio level meter display.
· On
· O󰀨
Remark:
only for SDI and HDMI/DVI signal.
Marker:

Sub Menu Description
Marker Enable [ON]All markers on.
[OFF]All markers o󰀨.
· ON
· OFF
Marker Select [OFF]NO marker displays.
[4:3]Marker display 4:3.
[16:9]Marker display 16:9.
[15:9]Marker display 15:9.
[14:9]Marker display 14:9.
[13:9]Marker display 13:9.
[1.85:1]Marker display 1.85:1.
[2.35:1]Marker display 2.35:1.
· OFF
· 4:3
· 16:9
· 15:9
· 14:9
· 13:9
· 1.85:1
· 2.35:1
Target Marker [ON]Turn on target marker.
[OFF]Turn on center mark.
[USER]Turn on user target tag.
· ON
· OFF
· USER
Safety Area [OFF]No Safety Area display.
[80%]80% Safety Area display.
[85%]85% Safety Area display.
[88%]88% Safety Area display.
[90%]90% Safety Area display.
[93%]93% Safety Area display.
· OFF
· 80%
· 85%
· 88%
· 90%
· 93%
Marker Level [White]Maker line is white.
[Gray]Marker line is gray.
[Black]Marker line is black.
· White
· Gray
· Black
Target Marker [OFF]Turn o󰀨 Fill up the background
beyond marker. [Gray]Background
beyond marker is gray. [Black]
Background beyond marker is black.
[Half Transparency]Background
beyond marker is half transparent .
· OFF
· Gray
· Black
· Half Transparency
Scope:
Sub Menu Description
Waveform Mode [OFF]Turn o󰀨 the waveform mode.
[LUMA]Display Y(luminance)
waveform. [YUV]Display YCbCr
waveform. [FULL LUMA]Display Y
(luminance) waveform, one-to-one
correspondence be-
tween its horizontal coordinates and
image horizontal coordinates.
· OFF
· LUMA
· YUV
· FULL LUMA
Waveform Alarm Waveform alarm can be set at any
percentage between 84%-100%, it
will alarm when measured waveform
reach or exceed the value you set
and mark them with red.
· 84%-100%
Waveform Scale [Digital]Display in digital.
[IRE]Display in percentage of
luminance.
· Digital
· IRE
Histogram Mode [OFF]Turn o󰀨 the histogram mode.
[LUMA]Display luminance
histogram. [RGB]Display R G B
histogram.
· OFF
· LUMA
· RGB
Vector Turn on/o󰀨 vector.
· ON
· OFF
1514
Embedded code: (Only for SDI signal)
Layout:
Sub Menu Description
Time Code Display Turn on/o󰀨 Time code.
· ON
· OFF
Time Code Mode [LTC]Time code display as LTC
mode. [VITC1]Time code display as
VITC1. [VITC2]Time code display as
VITC2.
· LTC
· VITC1
· VITC2
Sub Menu Description
Vector Scale [100%]Vector 100% display.
[75%]Vector zoom out to 75%
display.
· 100%
· 75%
Zebra Turn on/o󰀨 zebra.
· ON
· OFF
Zebra Level Zebra level can be set at any
percentage between 84%-100%, it
will alarm when measured luminance
reach or exceed the value you set
and overlay display with red zebra
stripes.
· 84%-100%
Pixel Measure Turn on/o󰀨 pixel measure.
· ON
· OFF
False Color Turn on/o󰀨 false color.
· ON
· OFF
Focus Assist Turn on/o󰀨 focus assist.
· ON
· OFF
Focus Gain Focus gainadjustment0-31.
· 0-31
Focus Color [Red]Focus color use Red.
[Green]Focus color use Green.
[Blue]Focus color use Blue.
[White]Focus color use White.
· Red
· Green
· Blue
· White
H Flip Turn on/o󰀨 Horizontal ip.
· ON
· OFF

Sub Menu Description
Layout [Single]Display only a single signal
picture on screen. [PIP]Display two
signals pictures simultaneously on
screen, the sub picture in the main
picture. [Side by Side]Display
two signals pictures side-by-side
simultaneously on screen, the sub
picture at the right side of the main
picture.
· Single
· PIP
· Side by Side
Remark:
In PIP/PBP mode, one of the signals
must be SDI1, the other signal is any
of other input signals. Can display 2
SDI simultaneously.
Main Window Source Main Window select signal input
among Video/ S-Video/ YPbPr/
SDI1/SDI2/VGA/ HDMI
· Video
· S-Video
· YPbPr
· SDI1
· SDI2
· VGA
· HDMI
· DVI
Remark:
YPbPr is compatible with RGB,
YCbCr, YPbPr.
Second Window
Source
Second Window select signal input
among Video/ S-Video/ YPbPr/
SDI1/SDI2/VGA/ HDMI
· Video
· S-Video
· YPbPr
· SDI1
· SDI2
· VGA
· HDMI
· DVI
Remark:
1.YPbPr is compatible with RGB,
YCbCr, YPbPr.
2.This item shows in PIP/PBP.
PIP Size [Large]The second window is Large
size. [Middle]The second window
is medium size. [Small]The second
window is small size.
· Large
· Middle
· Small
Remark:
1.This item shows in PIP.
Sub Menu Description
PIP position [Left Top]The second window
in the left-top corner of screen.
[Right Top]The second window in
the right-top corner. [Center]The
second window in the center. [Right
Bottom]The second window in the
right-bottom corner.[Left Bottom]
The second window in the left-
bottom corner. [Custom]The second
window is adjusted by user.When
the user selects this option, it will
automatically pop up at the following
"horizontal position" and "vertical
position" menu items.
· Left Top
· Right Top
· Center
· Right Bottom
· Left Bottom
· Custom
H Position Horizontal position adjustment of
picture-in-picture’s second window.
· 0-100
Remark:
This item shows when PIP position
selects “Custom”
V Position Vertical position adjustment of
picture-in-picture’s second window.
· 0-100
Remark:
This item shows when PIP position
selects “Custom”
Alpha Blend Adjustment of PIP’s second window
and the main window alpha blend
degrees. When the value is 0, the
second window is translucent blend
with the main window; when the
value is 100, the second window
blend directly to the main screen.
· 0-100
Swap In PIP and PBP, turn right the
VOLUME knob to swap the signal
pictures between two windows (main
window and second window).
· <Right> to swap two windows
Remark:
This item shows in PIP/PBP mode.
1716
Sub Menu Description
UMD Display Turn on/o󰀨 the UMD display.
· ON
· OFF
UMD ID UMD ID can be set any value
from 128-255. It can be used for
multidevice cascading, set di󰀨erent
UMD ID for di󰀨erent devices. In
remote control situation, this function
can be used for distinguishing
di󰀨erent devices so as to remote
control di󰀨erent devices.
· 128-255
UMD Position [Top Left]UMD display at Top Left.
[Top Center]UMD display at Top
Center.[Bottom Center]UMD
display at Bottom Center.[Bottom
Right]UMD display at Bottom Right.
· Top Left
· Top Center
· Bottom Center
· Bottom Right
UMD Local Color [GREEN]UMD character display in
green. [RED]UMD character display
in red. [White]UMD character
display in white.
· GREEN
· RED
· White
UMD Main Window
Char
It can be set any character in
“xxxxxxxx”.Setup process: Select
the UMD Main Window item, press
VOLUME knob, it shows “xxxxxxxx
ok”, meanwhile, the rst character
becomes red, user can select the
character you need by rotating the
VOLUME knob (Left/Right), press
the VOLUME knob after nishing rst
character, it will turn to the second
character, select the character you
need same as rst character, it’s also
applied to other characters. After
nishing selecting the 8th character,
press the VOLUME knob, the “ok”
will turn red, rotate the VOLUME
knob to make the “ok” turn yellow,
press MENU to save and exit. Only
the “ok” turn yellow, it will save
successfully when press MENU,
otherwise, it will not save.
UMD Second Window
Char
Setting is same as UMD Main
Window Char.
· xxxxxxxx
Remark:
This item shows in PIP.
Sub Menu Description
Current Source
Rename
The current signal rename display
characters can be arbitrarily set in
8 "xxxxxxxx". The setting process:
Select the option to the character
option, press the VOLUME (LETF
/ RIGHT) knob, the option is
displayed as "xxxxxxxx ok", and
the rst character becomes red,
the user can rotate VOLUME
(LETF / RIGHT) Button to select
the desired character. After the rst
bit is nished, press the VOLUME
(LETF / RIGHT) knob, the second
character will be skipped, the
second character will be red, and
the VOLUME (LETF / RIGHT) Select
the desired character, and so on, the
eighth character selection, when the
eighth character selection is good,
press the VOLUME (LETF / RIGHT)
knob, then "ok" will turn red, rotate
VOLUME (LETF / RIGHT ) Knob to
"ok" will turn yellow, then press the
MENU button to save the exit can
be completed UMD main screen
character settings. In the setting,
only the character "ok" for the yellow
state press the MENU button to exit
will make the previous character
settings saved successfully. If you
do not change the "ok" character
from red to yellow and press MENU
to exit, the previously set characters
are not saved.
IMD: