Koolatron KoolScapes PG04 User manual

W rr nty
This KOOLATRON product is warranted to the retail customer for 90 days from date of
retail purchase, against defects in material and workmanship.
WHAT IS COVERED
• Replacement parts and labour.
• Transportation charges to customer for the repaired product.
WHAT IS NOT COVERED
• Damage caused by abuse, accident, misuse, or neglect.
• Transportation of the unit or component from the customer to Koolatron.
IMPLIED WARRANTIES
Any implied warranties, including the implied warranty of merchantability are also limited to
the duration of 90 days from the date of retail purchase.
WARRANTY REGISTRATION
Register on-line at www.koolatron.com AND keep the original, dated, sales receipt with
this manual.
WARRANTY AND SERVICE PROCEDURE
If you have a problem with your PRODUCT, or require replacement parts, please telephone
the following number for assistance:
North Americ 1-800-265-8456
Koolatron has Master Service Centres at these locations:
Kool tron U.S.A.
4330 Commerce Dr.
Batavia, NY 14020-4102 U.S.A.
Kool tron C n d
27 Catharine Ave.
Brantford, ON N3T 1X5 Canada
A Koolatron Master Service Centre must perform all warranty work.
www.koolatron.com
©2009 Koolatron, Inc. All rights reserved. All specification are subject to change without notice.
Made in China 11/2009-v1H1S105
Please Read These Instructions Carefully Before Use!
User M nu l
PG04
POND GLO
4-pc underwater pond lighting

INSTRUCTIONS
1. Place in the pond or garden as desired, the base needs to be level.
2. If placed in the water, carefully place the light so that the top of the unit is approximately
1 foot (30.5cm) below the water level. If the unit is placed too deep the brightness will
be reduced, the water depth should not surpass 0.5m (1.7ft). The lights direction is done
manually.
3. Connect the power supply cord from the light unit to AC 12V power adapter.
4. It must be connected to the power source indoors by permanently wiring to a RCD
(Residual Current Device) protected fuse fixed spur in accordance with the IEE Wiring
Regulations.
5. Ensure the cable is adequately protected by routing through conduit prior to connecting
to mains supply.
6. Lenses can be replaced with any of the colour lenses supplied by carefully unclipping
from the front of the unit. The unit should be turned off and allowed to cool down before
changing lenses.
7. Switch off the power after 12 hours’ operation, with 20 minutes interval.
. Switch off the power when the lights are not in use for a long period of time.
WARNING
• Do not lift the lights by the power cable.
• If the cable is damaged, the lights should not be used. The cable can not be replaced.
• Only use clean water.
• The electrical components of the pond light must never come in contact with water.
• Do not let children operate the light unit without supervision.
• Never positioned on or near any electrical appliances.
• Disconnect the electrical power before cleaning, adjusting the light angle or changing the
coloured lens.
• Always keep the cable away from high temperature and fire.
CHANGING THE BULB
The light should be removed from the water and dried before replacing the bulb. The light
should also be unplugged. To start remove the lid by twisting counter clock wise as per
directional arrow. Remove lens, then gently remove the bulb from the base.
Replace with a new bulb by simply inserting the prongs
into the base of the light. Replace the lens and lid.
When closing the light it is important to ensure the bulb
in the light is perfectly centered. If the bulb is leaning to
one side it will heat that side and could cause a leak.
Reassemble the light and place back into the pond.
CARE AND MAINTENANCE
The Pond Glo Light Set requires minimal maintenance during the spring and summer
months, however, it must be brought inside during the winter months. This is to ensure the
light doesn’t crack over the winter. To bring the light in simply unplug the transformer and
remove the light from the pond. Dry all parts of the light and transformer and store in a dry
place.
INSERTING THE COLOURED LENS
To change the color of the light from white to another,
there are four colored lenses provided, select the
colored lens and gently insert it into the top of the light
assembly ensuring that the two grooves in the lens fit
over the center stems on the light at the top
color lens
fixed cover
transparent cover
seating
lamp
body
holder
pedestal
screw
power
supply cord