KoolScapes CSFK-5 User manual

User Manual
CSFK-5
SOLAR CASCADING FOUNTAIN KIT
WARRANTY
This KOOLATRON product is warranted to the retail consumer for 90 days from date of
retail purchase, against defects in material and workmanship.
WHAT IS COVERED
- Replacement parts and labor.
- Transportation charges to customer for the repaired product.
WHAT IS NOT COVERED
- Commercial or industrial use of this product.
- Damage caused by abuse, accident, misuse, or neglect.
- Transportation of the unit or component from the customer to Koolatron.
IMPLIED WARRANTIES
Any implied warranties, including the implied warranty of merchantability are also limited to duration
of 90 days from the date of retail purchase.
WARRANTY AND SERVICE PROCEDURE
Keep the original, dated, sales receipt with this manual. If you have a problem with your unit,
or you require replacement parts, please telephone the following number for assistance:
1-800-265-8456
A Koolatron Master Service Centre must perform all warranty work. Service after warranty
may be obtained at a Master Service Centre or at an authorized service dealer.
Purchase Receipt is required to establish warranty eligibility.
Koolatron has Master Service Centres at these locations:
U.S.A. - 4330 Commerce Dr., Batavia, NY 14020-4102
Canada - 139 Copernicus Blvd., Brantford, ON N3P 1N4
www.koolatron.com
©2020 Koolatron, Inc. All rights reserved.
All specification are subject to change without notice.
Made in China 5/2020-v3H1S108 Please Read These Instructions Carefully Before Use!

COMPONENTS
- solar panel
- pole 1
- pole 2
- panel support
- pump with plug
OVERVIEW
• The solar pump is designed for outdoor fountain use, and is powered by a solar panel.
In order to make the pump work by solar energy, the solar panel needs to be placed in
the sunlight facing the sun.
• The performance of the pump depends on the sunlight intensity and the orientation of
the solar panel.
ASSEMBLING
1. Unpack all components carefully.
2. Find a suitable spot and place bowls on the stand.
3. Loop the tube from the top pitcher through
the stand’s small loops. See picture.
4. Place pump in the bottom bowl.
5. Connect the end of tube to the adapter on
the top of the pump.
6. Connect the pump’s cable to the assembled
solar panel.
7. Fill bottom bowl with water, making sure the
pump is fully submersed.
8. Place solar panel in direct sunlight.
8. The pump is now ready to operate.
CAUTIONS
• Any altering of the product itself or changing of the components is forbidden.
• Operate the pump in freshwater or saltwater only (never above 30°C).
• Keep it away from flammable liquids.
• Do not strike the solar panel.
• Do not let the pump run dry.
CLEANING AND MAINTENANCE
• If after some time the pump starts losing power or stops working, please clean up
sediment in the pump shell or filter cribs.
• The pump can be opened by pressing down at the bottom of the filter housing.
(see the photo below)
• To clean the impeller, open the pump housing at the front by sliding up the front plastic
cover.
• The solar module should only be cleaned with soft tissue and glass cleaning solution.
TECHNICAL DATA
Peak Power of Solar Panel 1.5W
Operation Voltage 8V DC
Maximum Water Lift Height 120cm (47.2”)
Maximum Flow Rate 230L (61 gallons) / h
Cable Length 5m (16.4 ft)
TROUBLESHOOTING
Pump does not operate even though the solar panel is in full sunlight.
• No connection to the solar module—check connection to the solar module.
• Impeller is blocked—to clean the pump, remove the front plate and the impeller,
use a brush or water to remove any debris.
Pump does operate but there is no water running through the tubes.
• Clear the tube and the filter.
filter
impeller
cover
impeller
front cover
WARNING! This product contains chemicals known to
the State of California to cause cancer, and birth defects
or other reproductive harm. www.P65Warnings.ca.gov