Korenix JetCon 2301S User manual

Mount the unit
Din-Rail mount: Mount the din-rail clip on the rear of JetCon 25301 on
the DIN rail. For information about the DIN Rail installation, please
refer to user’s manual.
Grounding JetCon 2301S
There is one grounding screw on the
bottom side of JetCon 2301S. Connect the
frame grounding of JetCon 2301S to the
grounding surface to ensure safety and
prevent noise for communication interference.
Wiring the Power Inputs
1. Insert the positive and negative wires into the V+ and V- contact on
the terminal block connector.
2. Tighten the wire-clamp screws to prevent the power wires loosened.
Note:
The recommended working voltage is DC 24V. (Input range: DC10~ 60 V)
JetCon 2301S is a single port Fast Ethernet to Fiber media converter,
supporting 4 types of forwarding modes –Store and Forward,
Modified Cut-through, Pure Converter and Converter with auto-
change modes. JetCon 2301S with IP31 grade enclosure and 1.5KV
Hi-Pot isolation protection to operate in harsh environments with
severe electromagnetic interference and -40~70°C.
JetCon 2301S
Quick Installation Guide v1.0
Copyright
Copyright © 2014 all rights reserved. No part of this publication may
be reproduced, adapted, stored in a retrieval system, translated into
any language, or transmitted in any form or by any means without
the written permission of the supplier.
About the Quick Installation Guide
This Quick Installation Guide is intended to guide professional
installer to install and configure the JetCon 2301S. It covers
procedures to assist you in avoiding unforeseen problems.
Installation
Introduction
2. Connecting the Fiber Port: Connect the fiber port on your JetCon
2301S to another Fiber Ethernet device, by following the figure
below. Wrong connection or fiber cable type will cause the fiber
port not working properly.
3. For different link distance,
the JetCon 2301S provides
JetCon 2301S-mw” for
multi-mode fiber and
“JetCon 2301S-sw” for
single-mode fiber.
4. The table below illustrates fiber
transceiver specification.
Wiring the Relay Output
The relay output contacts are in the middle of the terminal block connector
as shown below. By inserting the wires and settings the DIP switch of the
respective alarm function to “ON”, relay output alarm will detect port or
power fault, and form a short circuit. The alarm relay output is “Normal
Open”. For more information, please refer Manual chapter for more detail.
Note:
The relay contact only support 1A current, DC 24V. It does not recommend
apply higher voltage and current that over this specification.
Connecting to Network
1. Connecting the Ethernet Port: Connect one end of an Ethernet cable
into the UTP port of JetCon 2301S, while the other end is connected
to the attached networking device. UTP port support auto
MDI/MDIX function. The LNK / ACT LED will turn on and flash to
indicate RJ-45 port link and the packets received and transmitted
from RJ-45.
Note:
To ensure your fiber converter can transmit/receive data between the
2 nodes, the attenuation of the optical fiber cable should be smaller
than the fiber converter’s Link Budget.
Attention:
This is a Class 1 Laser/LED product. Don’t stare into the Laser/LED
Beam.
DIP Switch Setting
Note:
After adjusting the DIP-switch, please reboot the unit to activate the
new settings.
Package Check List
JetCon 2301S Industrial Media Converter
Quick Installation Guide 5 Years Warranty
Each of Korenix’s product line is designed, produced, and tested with
high industrial standard. Korenix warrants that the Product(s) shall be
free from defects in materials and workmanship for a period of five (5)
years from the date of delivery provided that the Product was properly
installed and used.
This is warranty is voided if defects, malfunctions or failures of the
warranted Product are caused by damage resulting from force measure
(such as floods, fire, etc.), other external forces such as power
disturbances, over spec power input, or incorrect cabling; or the
warranted product is misused, abused, or operated, altered and
repaired in an unauthorized or improper way.
Attention! To avoid system damage caused by sparks, please DO NOT
plug in power connector when power is on.
The product is in compliance with Directive 2002/95/EC and 2011/65/EU
of the European Parliament and of the Council of 27 January 2003 on the
restriction of the use of certain hazardous substances in electrical and
electronics equipment (RoHS Directives & RoHS 2.0)
Korenix Customer Service
KoreCARE is Korenix Technology's global service center, where our
professional staff are ready to solve your problems at any time Korenix
global service center's e-mail is [e-mail].
For more information and documents download please visit our website:
http://www.korenix.com/downloads.htm
Support

连接到网络
1. 连接以太网端口：将以太网电缆的一端连接到JetCon 2301S的
UTP端口，另一端连接到所连接的网络设备。 UTP端口支持自
动MDI/ MDIX功能。 LNK / ACT LED将亮起并闪烁，表示RJ-
45端口链路和从RJ-45接收和发送的数据包。
2. 连接光纤端口：将JetCon 2301S
上的光纤端口连接到另一个光纤
太网设备，如图所示。 连接错误
或光缆类型会导致光纤端口工
作不正常。
注意:
推荐的输入电压为DC 24V。(可输入范围：DC10〜60V)
接线输出
继电器输出触点位于连接器端子中间，如下所示。 透过将警报功能
的DIP开关插入到“ON”，继电器输出报警将检测端口或电源故障，
并形成短路。 有关更多信息，请参阅手册章节了解更多详细信息。
版权
版权所有©2014保留所有权利。 未经供应商书面许可，不得将
本出版物的任何部分复制，改编，存储在检索系统中，翻译成任
何语言，或以任何形式或方式传播。
关于快速安装指南
本“快速安装指南”旨在指导专业安装人员安装和配置JetCon
2301S。 它涵盖了帮助您避免意外问题的程序。
常规
警告:此符号表示您必须遵守的警告
注意:此符号表示您必须注意的重要注意事项。
安装
介绍
注意:
继电器触点仅支持
1A电流，DC 24V
。 不建议使用超过
本规范的更高的电
压和电流。
注意:
1. 为确保光纤转换器能够在2个节点之间传输/接收数据，光纤电
缆的衰减应小于光纤转换器的链路预算。
2. 这是1类激光/ LED产品。 不要盯着激光/ LED光束。
DIP拨码开关设定
注意:
1. 调整DIP开关后，请重新启动本机以激活新设置
2. 设为100Full 时, 另一方设备建议设为自适应 Auto
Din-Rail支架：
将JetCon 25301背面的Din-rail夹子安装在DIN导轨。有关DIN
导轨安装的信息请参考用户手册。
JetCon 2301S 接地:
JetCon 25301底部有一个接地螺丝。
将JetCon 2301S连接框架接地以保
证安全，防止噪音用于通信干扰。
输入电源接线:
1.将正极和负极线插入端子块连接器上的V +和V-触点。(如下图)
2.拧紧电线夹螺钉，防止电源线松动。
JetCon 2301S 是单端口快速以太网到光纤介质转换器，支持4种
转发模式 -存储转发，快速发送模式 ，纯转换器和自动更改模
式转换器。 JetCon 2301S具有冗余电源输入，6孔可拆卸端子，
具有宽范围DC10〜60V。JetCon 2301S的光纤端口也支持单模
或多模，最高高达30KM的延长距离传输。
打開包裝，檢查下列配件
•JetCon 2301S工业媒体转换器*1
•快速安装指南*1
Korenix Technology Co., Ltd.
(A Beijer Electronics Group Company)
Tel:[phone]
Fax:[phone]
Business service:[e-mail]
Customer service: [e-mail]
www.korenix.com
CPQ000V2301002
Patent No. (Taiwan):
Granted Invention: I 313547
Granted Invention: I 321415
Granted Invention: I 344766
Granted Invention: I 346480
Granted Invention: I 356616
Granted Invention: I 364684
Granted Invention: I 376118
Granted Invention: I 393317
Granted Invention: I 398066
Granted Invention: I 398125
Granted Invention: I 459757
Utility Model: M 339841
Utility Model: M 339840
客户服务
5年质保
所有Korenix产品的设计、制造及测试都是采用较高的工业标准。
Korenix保证自产品出货日起提供最高5 年之免费保修服务，保修
期间如因零件损坏或制程不良而导致产品故障，我们提供免费维
修服务。自然外力 （火、水、雷灾）所造成的产品故障，或其它
外部因素如电源干扰、不当电源输入、不当接线等造成的损坏，
不列入产品保固范围；此外，产品被误用、未经授权的修理及修
改等行为将造成保固条款失效。
注意! 请勿于电源开启时插拔接线端子，避免产生火花造成系统
损坏。
此产品保证完全符合欧盟2003年1月27日电气和电子设备危害物
质限制委员会限用指令2002/95/EC (RoHS)及2011/65/EU(RoHS
2.0)。
Korenix售后服务
KoreCARE 是Korenix科技全球服务中心，我们专业的技术人员随
时准备解答您的疑问。
Korenix全球服务中心 EMAIL: [e-mail]
业务服务: [email protected]
官网: www.korenix.com.cn
3. 对于不同的链距离，需用不同的设备，JetCon 2301S为多模
式提供JetCon 2301S-mw“光纤和“JetCon 2301S-sw”用
于单模纤维。
4. 下表列出了光纤收发器规范。