Korenix JetCon 2302 User manual

5 Years Warranty
Each of Korenix’s product line is designed, produced, and tested with high industrial
standard. Korenix warrants that the Product(s) shall be free from defects in materials and
Support
Support
workmanship for a period of ve (5) years from the date of delivery provided that the
Product was properly installed and used.
is warranty is voided if defects, malfunctions or failures of the warranted Product are
caused by damage resulting from force measure (such as oods, re, etc.), other external
forces such as power disturbances, over spec power input, or incorrect cabling; or the
warranted Product is misused, abused, or operated, altered and repaired in an unauthorized
or improper way.
Attention! To avoid system damage caused by sparks, please DO NOT plug in power
connector when power is on.
e product is in compliance with Directive 2002/95/EC and 2011/65/EU of the European
Parliament and of the Council of 27 January 2003 on the restriction of the use of certain
hazardous substances in electrical and electronics equipment(RoHS Directives & RoHS 2.0)
Korenix Customer Service
KoreCARE is Korenix Technology's global service center, where our professional stas are
ready to solve your problems at any time Korenix global service center's e-mail is
[email protected].
For more information and documents download please visit our website:
http://www.korenix.com/downloads.htm
Installation
Mount the unit
Din-Rail mount: Mount the din-rail clip on the rear of JetCon 2302 on
the DIN rail. For information about the DIN Rail installation, please
refer to user’s manual.
Wiring the Power Inputs
1. Insert the positive and negative wires into the V+ and V- contact on the terminal block
connector.
2. Tighten the wire-clamp screws to prevent the DC wires from being loosened.
3. Both of the redundant power inputs accept negative or positive type power source; the
negative power source is commonly used in telecom applications. See the gure-1 and gure-2
for the power wiring.
Note: e recommended working voltage is DC24V (DC10~ 60V); both power inputs
should apply with the same power system; either positive or negative.
Wiring the Relay Output and Chassis Grounding
e relay output alarm contacts are in the middle of the terminal block connector as shown in
the gure below.
By inserting the wires and setting the DIP switch of the respective Port Alarm to “ON”, relay
output alarm will detect any port failure and form a short circuit. e alarm relay output is
“Normal Open”. Please refer to Figure -3 for the relay wiring architecture.
Operating Mode Selection
e JetCon 2302 is not only a 4-port Switch, but it is also a 2-channel Fast Ethernet Media
Converter. It is congured by the DIP switch and activated through the power resetting or the
reset button. To understand the functions of the Switching and converter modes, refer to the
table below:
In an industrial environment there might be
a lot of devices that generate electromagnetic
noise, such as AC motors, electric welding
machines and power generators. ese
devices will generate electric noise or surges
that might disturb communication. To
prevent these interferences, the JetCon 2302
should be well earthed.
Connecting to Network
1. Connecting the Ethernet Port: Connect the Ethernet RJ-45 port to another networking
device by properly twisted cable (UTP or STP). If the port is well linked with partner, the
Link LED (Green) will turn on and the Activity LED will start blinking slowly when the
packets are transmitting and receiving. e RJ-45 ports support MDI/MDI-X function.
2. Connecting the Fiber Port: Connect the ber port to ber link partner by proper ber
cable as shown in the Figure-4. Ensure that both of connected ber ports are the same type
and use exactly optical ber cable.
！
is is a Class 1 Laser/LED product.
Don't look into the Laser/LED Beam.
ATTENTION
RX
TX
RX
TX
Cable Wiring(SC to SC)
RX A TX B
TX A RX B
DIP Switch Setting
Package Check List
 JetCon 2302 Industrial Media Converter
 Quick Installation Guide
JetCon 2302 Industrial Fast Ethernet to Fiber Media Converter
Quick Installation Guide V1.3
JetCon 2302 is a Fast Ethernet to Fiber Media Converter with 2 Fast Ethernet copper and 2
ber ports allowing the device to act as 4 port Fast Ethernet Fiber switch or 2-channel
Converter for exible industrial applications. In switch mode, JetCon 2302 is an industrial
4-port 10/100Mbps Fast Ethernet Switch, incorporating 3.2Gbps switching fabric with
non-blocking store and forward technology to fulll the high transmission performance
requirements. In converter mode, JetCon 2302 is a cost eective industrial 2-channel
10/100TX to 100FX media converter with an error packet ltering function. It also provides
relay alarm output function for the port and power alert. e heavy industrial EMC compliant
JetCon 2302, designed with IP31 grade enclosure, is equipped with dual redundant
DC10~60V power inputs and provides 1.5KV Hi-Pot isolation protection and wide operating
temperature, therefore ensuring highly reliable network performance under harsh industrial
environments with vibration and shock.
Overview
A Beijer Electronics Group Company
Figure -3
Converter mode
No.
Port 1, 3 grouped as a single channel A
Port 2, 4 grouped as a single channel B
Store and forward
Fully supported
Switching mode
Yes
Store and forward
Fully supported
Data exchange
Forward Technology
Port Event Alarm
Description
Port link down event alarm enabled.
Port link down event alarm disabled. (Default)
Enabled Converter mode
Switch mode. (Default)
Enabled power event alarm
Disabled power event alarm (Default)
Status
ON
Off
ON
Off
ON
Off
Not avaliable
Pin No. #
DIP 1~4
DIP 5
DIP 6
DIP 7
DIP Switch Setting
Description
Green on: the port is linked well with partner
Green blinking: the port is transmitting packet.
Green on: the port is linked well with partner.
Green blinking: the port is transmitting packet.
Green on: the power is on applying.
Red on: port link down or power off event occurred, and the
alarm relay output conductors formed a short circuit.
Green on: the device is setting on the converter mode.
LED color
Green
Yellow
Green
Yellow
Green
Red
Green
Indicators
Ethernet
RJ-45
Fiber
PWR 1,2
Con.
Alm
PackageCheckList
 JetCon2301IndustrialMediaConverter
 QuickInstallationGuide
ABeijerElectronicsGroupCompany
JetCon2301IndustrialFastEthernettoFiberMedia Converter
QuickInstallationGuideV1.1
JetCon2301isasingleportFastEthernet to Fiber media converter, supporting 4 types of
forwardingmodes–Storeand Forward, Modied Cut-through, Pure Converter and
Converterwithauto-changemodes.eJetCon2301 adopts rugged aluminum case with
IP31gradeenclosureand 1.5KV Hi-Pot isolation protection to operate in harsh
environmentswithsevereelectromagneticinterference and -25~70°C (JetCon 2301) or
-40~75°C(JetCon2301-w).ItfeaturesLinkLossForwardingto forward link status changes
foralertingremoteorcentral management systems when a remote fault occurs. It also
adoptsonerelayoutputtoalarmusersifa port link fails or if the power fails. Alarms can be
enabled/disabledbydipswitch.JetCon2301has redundant power inputs with widerange
DC10~60Vthroughthe6-pin removable terminal block. e ber port supports
Single-modeorMulti-modeforprovidingupto30KMextendeddistance transmission.
Overview
Package Check List
 JetCon2302 Industrial Media Converter
 QuickInstallation Guide
JetCon2302 Industrial Fast Ethernet to Fiber Media Converter
QuickInstallation Guide V1.3
JetCon2302 is a Fast Ethernet to Fiber Media Converter with 2 Fast Ethernet copper and 2
ber ports allowing the device to act as 4 port Fast Ethernet Fiber switch or 2-channel
Converter for exible industrial applications. In switch mode, JetCon 2302 is an industrial
4-port 10/100Mbps Fast Ethernet Switch, incorporating 3.2Gbps switching fabric with
non-blocking store and forward technology to fulll the high transmission performance
requirements. In converter mode, JetCon 2302 is a cost eective industrial 2-channel
10/100TX to 100FX media converter with an error packet ltering function. Italso provides
relayalarm output function for the port and power alert. e heavy industrial EMC compliant
JetCon 2302, designed with IP31 grade enclosure, is equipped with dual redundant
DC10~60Vpower inputs and provides 1.5KV Hi-Pot isolation protection and wide operating
temperature, therefore ensuring highly reliable network performance under harsh industrial
environmentswith vibration and shock.
Overview
ABeijer Electronics Group Company

选择工作模式
JetCon 2302不仅是一款4口交换机，同时也是一个两通道快速光电信号转换器，可
通过DIP拨码开关切换不同的工作模式。当完成设定后，请重启电源或按重置键让
新设置生效。交换机模式与转换器模式的功能比较，请参考下表:
5年质保
所有科洛理思产品的设计、制造及测试都是采用较高的工业标准。科洛理思保证
自产品出货日起提供最高5 年之免费保修服务，保修期间如因零件损坏或制程不良
而导致产品故障，我们将提供免费维修服务。
然而，自然外力(火、水、雷灾)所造成的产品故障，或其它外部因素如电源干扰、
不当电源输入、不当接线等造成的损坏，不列入产品保固范围；此外，产品被误
用、未经授权的修理及修改等行为将造成保固条款失效。
客户服务
注意! 请勿于电源开启时插拔接线端子，以避免产生火花造成系统损坏。
此产品保证完全符合欧盟2003年1月27日电气和电子设备危害物质限制委员会所提
出的限用指令2002/95/EC(ROHS禁令)及2011/65/EU(RoHS 2.0)。
Korenix售后服务
KoreCARE 是科洛理思科技全球服务中心，我们专业的技术人员随时准备解答您的
疑问。科洛理思全球服务中心 EMAIL: [email protected]
详细说明及文件请至网站下载: http://www.korenix.com.cn/support_downloads.htm
业务服务: [email protected]
官网: www.korenix.com.cn
在工业环境下，有许多产生电磁干扰的设备，例如AC电动机、电子焊接机、发电机
，而这些设备产生的电噪声及突波，可能使网络通讯受到影响。
将地线螺丝接地，确保设备安全，防止电气干扰。设备未接地，因自然因素造成损
害，将不予以修复。
3. 两路冗余电源支持正负极电源输入，负极电源输入通常使用在电信业中。电源
线配线请参考图1及图2。
电源线连接
1. 将电源线正负极插入产品底部接线端子的V+和V-接脚。
2. 将线夹螺丝拧紧，防止DC电源线脱落。
Patent No. (Taiwan):
Granted Invention: I 313547
Granted Invention: I 321415
Granted Invention: I 344766
Granted Invention: I 346480
Granted Invention: I 356616
Granted Invention: I 364684
Granted Invention: I 376118
Granted Invention: I 393317
Granted Invention: I 398066
Granted Invention: I 398125
Utility Model: M 339841
Utility Model: M 339840
Tel:[phone]
Fax:[phone]
Business service:[email protected]
Customer service:[email protected]
www.korenix.com
CPQ000V2302003
Korenix Technology Co., Ltd.
(A Beijer Electronics Group Company)
JetCon 2302不仅是一款紧凑型4口百兆以太网交换机，同时也是一个双通道百兆光
电信号转换器，可灵活应用在不同领域中。在交换模式下，JetCon 2302是一款4口
快速工业以太网交换机，拥有3.2Gbps无阻塞交换矩阵及存储转发交换技术，满足高
品质数据传输需求。在转换器模式下，JetCon 2302是一款2通道百兆光电信号转换
器，支持端口故障检测，维护轻松便捷。JetCon2302满足NEMA-TS2标准，采用
IP31工业防护等级的外壳设计，不仅支持DC10~60V冗余电源输入，还支持1.5KV
Hi-Pot高压隔离保护，支持-40~75oC工作环境，能确保在恶劣环境下提供高可靠度
，高性能的数据传输服务。
导言
安装配件
导轨安装：将导轨夹固定在 JetCon 2302 的背面，
然后卡上导轨。更多导轨安装信息，请参考用户操作手册。
安装
产品清单
 JetCon 2302工业信号转换器
 快速安装向导
备注: 建议供电范围：DC24V (DC10~60V); 两路电源输入需有相同的系统电源型态
(正极或负极)。
继电器报警输出和地线连接
继电器报警系统接脚位于接线端子
中部，如右图所示。继电器报警输
出配线结构，请参考图3。接线后并
将其DIP拨码开关拨到”ON”，继电
器报警功能即开始侦测端口是否有
误。此功能为常开。
图3
网络连接
1. 连接以太网口：使用合适的双绞线(UTP或STP)连接JetCon 2032 RJ-45电口和另一
台网络设备。当Link LED灯显示绿色，且Activity LED灯开始闪烁，表示设备已正确
连接且有数据正在传递。RJ-45电口自适应MDI/MDI-X。
2. 连接光口：使用光纤线连接JetCon 2302光口及其它光口设备，如图所示。并确保
两个光口是同类型，且使用相同的光纤线缆。
！
is is a Class 1 Laser/LED product.
Don't look into the Laser/LED Beam.
ATTENTION
RX
TX
RX
TX
Cable Wiring(SC to SC)
RX A TX B
TX A RX B
转换器模式
不可
Port 1, 3组成独立的信道A进行数据传输
Port 2, 4组成独立的信道B进行数据传输
存储转发
支持
交换机模式
可
存储转发
支持
数据交换
转发技术
端口事件报警
DIP 拨码开关设置
LED指示灯
描述
启动端口连线情况报警
关闭端口连线情况报警(默认)
转换器模式
交换机模式(默认)
启动电源事件报警
关闭电源事件报警(默认)
状态
ON
Off
ON
Off
ON
Off
No function
DIP拨码开关
DIP 1~4
DIP 5
DIP 6
DIP 7
说明
绿灯亮：此端口正常连接
绿灯闪烁：有数据正在传递
绿灯亮：此端口正常连接
黄灯闪烁：有数据正在传递
绿灯亮：电源使用中
红灯亮：断线或断电的情况发生，造成继电器报警短路
绿灯亮：设定JetC on 230 2为转换器模式
LED 颜色
绿灯
黄灯
绿灯
黄灯
绿灯
红灯
绿灯
指示灯
以太网
R J-45
光口
PWR 1,2
转换器模式
继电器报警
PackageCheckList
 JetCon2301IndustrialMediaConverter
 QuickInstallationGuide
ABeijerElectronicsGroupCompany
JetCon2301IndustrialFastEthernettoFiberMedia Converter
QuickInstallationGuideV1.1
JetCon2301isasingleportFastEthernet to Fiber media converter, supporting 4 types of
forwardingmodes–Storeand Forward, Modied Cut-through, Pure Converter and
Converterwithauto-changemodes.eJetCon2301 adopts rugged aluminum case with
IP31gradeenclosureand 1.5KV Hi-Pot isolation protection to operate in harsh
environmentswithsevereelectromagneticinterference and -25~70°C (JetCon 2301) or
-40~75°C(JetCon2301-w).ItfeaturesLinkLossForwardingto forward link status changes
foralertingremoteorcentral management systems when a remote fault occurs. It also
adoptsonerelayoutputtoalarmusersifa port link fails or if the power fails. Alarms can be
enabled/disabledbydipswitch.JetCon2301has redundant power inputs with widerange
DC10~60Vthroughthe6-pin removable terminal block. e ber port supports
Single-modeorMulti-modeforprovidingupto30KMextendeddistance transmission.
Overview
Package Check List
 JetCon2302 Industrial Media Converter
 QuickInstallation Guide
JetCon2302 Industrial Fast Ethernet to Fiber Media Converter
QuickInstallation Guide V1.3
JetCon2302 is a Fast Ethernet to Fiber Media Converter with 2 Fast Ethernet copper and 2
ber ports allowing the device to act as 4 port Fast Ethernet Fiber switch or 2-channel
Converter for exible industrial applications. In switch mode, JetCon 2302 is an industrial
4-port 10/100Mbps Fast Ethernet Switch, incorporating 3.2Gbps switching fabric with
non-blocking store and forward technology to fulll the high transmission performance
requirements. In converter mode, JetCon 2302 is a cost eective industrial 2-channel
10/100TX to 100FX media converter with an error packet ltering function. Italso provides
relayalarm output function for the port and power alert. e heavy industrial EMC compliant
JetCon 2302, designed with IP31 grade enclosure, is equipped with dual redundant
DC10~60Vpower inputs and provides 1.5KV Hi-Pot isolation protection and wide operating
temperature, therefore ensuring highly reliable network performance under harsh industrial
environmentswith vibration and shock.
Overview
ABeijer Electronics Group Company