Kozy-World GFN2815R Quick start guide

1
VENT-FREE GAS
FIREPLACESYSTEM
WARNING: Iftheinformation
in thismanualisnotfollowed
exactly,afireorexplosionmay
resultcausingpropertydamage,
personalinjury,orloss oflife.
*Aftermarket: Completionofsale, notfor purpose of
resale,fromthemanufacturer.
Donotstoreorusegasolineorotherflam-
mablevaporsand liquids inthe vicinityofthis
orany
otherappliance.
WHATTO DOIF YOUSMELL GAS
l Donottrytolight any appliance.
l Donottouchanyelectricalswitch;do
notuse any phoneinyourbuilding.
l Immediatelycall yourgas supplier
fromaneighbor sphone.Followthe gas
supplier sinstructions.
l Ifyoucannotreach yourgas supplier,
callthefiredepartment.
Installation and service must be performed
byaqualifiedinstaller,serviceagency,or
thegassupplier.
WARNING:Improperinstallation,
adjustment, alteration,service ormaintenance
can cause injuryorpropertydamage.Refertothis
manualforcorrectinstallationandoperational
procedures.Forassistanceoradditionalinfor-
mationconsultaqualified installer,serviceagency,
orgas supplier.
Thisappliancemaybeinstalledin an
aftermarket*, permanentlylocated, manu-
factured(mobile)home,where notpro-
hibitedbylocal codes.
Thisappliance isonlyforuse withthe
typeofgas indicated on therating plate.
Thisapplianceisnotconvertibleforuse
withother gases.
Installer:Pleaseleave theseinstructionswiththe
consumer.
Consumer:Pleaseretain theseinstructionsfor
futureuse.
WATERVAPOR:ABY-PRODUCTOFUNVENTED
ROOMHEATERS
Watervaporisaby-product ofgascombustion.
Anunvented roomheaterproducesapproximately
one (1)ounce(30ml)ofwaterforevery 1,000 BTU s
(.3KW s)ofgasinputperhour. Refertopage4.
WARNING: Thisisanunvented gas-fired
heater.Ituses air(oxygen)fromtheroomin
which it isinstalled.Provisionsforadequate
combustionandventilationairmustbeprovided.
RefertoAirForCombustionandVentilation
sectiononpage 5of thismanual.
OWNER SOPERATIONANDINSTALLATION MANUAL
GFN2815RGFP2816R
GFN2817RGFP2818R
GFN2819RGFP2820R
Kozy-WorldR
WorldMarketing ofAmerica, Inc.
P.O.Box192, Rt.. 22West
Mill Creek, PA17060
KOZYWORLDPHONENUMBER:[phone]
http://www.worldmkting.com
KW-BL035-03RHW-0505

2
TableofContents
SafetyInformationWarnings....................................3
AirforCombustionandVentilation...........................5
Installation...............................................................7
Operating heater.....................................................10
Cleaning&Maintenance...........................................13
Trouble Shooting....................................................15
Specifications.........................................................16
Replacement.........................................................17
PartsList................................................................18
Logsinstallationinstruction.....................................22
Mantelinstallationinstructions................................23
Assemblinganchor.................................................28

3
IMPORTANT:Readthisowner s
manualcarefullyandcompletely
beforetrying toassemble, operate,
orservicethisheater.Improperuse
ofthisheatercancause seriousin-
juryordeathfromburns,fire,
explosion,electricalshock,andcar-
bonmonoxide poisoning.
SAFETYINFORMATIONWARNINGS
DANGER: Carbonmonoxide
poisoning mayleadtodeath!
CarbonMonoxidePoisoning: Early
signsofcarbon monoxidepoisoning
resemblethe fluwithheadaches,
dizziness,ornausea.Ifyouhave
thesesigns,theheatermaynotbe
workingproperly.Getfreshair
immediately!Have heaterserviced.
Somepeoplearemoreaffectedby
carbonmonoxidethanothers.These
includepregnantwomen, peoplewith
heart,or lungdisease,anemia, those
undertheinfluenceofalcohol, and
those at high altitudes.
Propane/LPGas: Propane/LPgas
isodorless.Anodor-makingagent
isaddedtoPropane/LPgas.The
odorhelpsyou detectaPropane/LP
gasleak. However,theodor added to
Propane/LPgas canfade. Propane/
LPgas maybepresenteventhough
no odorexists.
Makecertainyoureadand under-
standallwarnings.Keepthismanual
for reference.Itisyourguidetosafe
andproperoperation
of thisheater.
WARNING: Any change to
thisfireplace oritscontrolscan
be dangerous.
WARNING:Donot allow
fans toblowdirectlyintotheheater.
Avoidanydraftsthatalterburner
flamepatterns. Ceilingfans cancre-
atedraftsthatalterburnerflame
patterns.Alteredburnerpatterns
cancausesooting. .
Donotplace clothingorother
flammablematerial on ornearthe
appliance. Neverplaceany objects
inthe fireplace.
Duetohightemperatures,the
applianceshouldbelocated outof
trafficand away fromfurniture
and draperies.
WARNING:Donotuse ablower
insert,heatexchangerinsert, or other
accessorynotapprovedfor usewith
thisheater.
Heaterbecomes veryhotwhen
runningfireplace.Keepchildrenand
adultsawayfromhotsurfacesto
avoidburns orclothing ignition.
Fireplacewill remainhotfora
timeaftershutdown. Allowsurfaces
tocoolbeforetouching.
Carefullysupervise young children
whenthey areinthe roomwith
fireplace.
Youmust operatethisheaterwith
the heaterscreen inplace.Make
sureheaterscreen isinplace
beforerunning heater.
Keep the appliancearea clearand
freefromcombustiblematerials,
gasoline,andotherflammable
vaporsandliquids.
1.Thisapplianceisonlyfor usewiththe
typeofgas indicatedon therating
plate.Thisapplianceisnotconvert-
ibleforusewithothergases.
2.Donotplace Propane/LPsupply
tank(s)insideanystructure.Locate
Propane/LPsupplytank(s) outdoors.
3.Ifyousmellgas Shutoffgassupply.
lDonot trytolight anyappliance.
lDonot touchanyelectricalswitch:
do notuseanyphone inyour building.
lImmediatelycall yourgassupplier
fromaneighbor sphone.Followthe
gassupplier sinstructions.
lIf youcannotreachyourgassupplier,
callthe firedepartment.
4.Thisheatershall notbeinstalledina
bedroomorbathroom.
5.Donotuse thisheateras awood-
burningheater.Useonlythelogspro-
videdwiththeheater.
6. Donotaddextralogsorornaments
suchas pine cones,vermiculite,or
rockwool. Using theseadded items
can causesooting.Donotaddlava
rockaroundbase.Rockanddebris
couldfallintothecontrolarea of
heater.Afterservicing,alwaysreplace
screenbeforeoperating heater.
7.Youmustoperatethisheaterwiththe
heater screen inplace.Make sureheater
screenisinplacebeforerunningheater.
8.Thisheaterisdesignedtobe
smokeless.If logseverappearto
smoke,turnoff heater and callaquali-
fiedserviceperson.Note:During ini-
tialoperation,slightsmoking could
occurdue tolog curingandheater
burningmanufacturing residues.
9.Topreventthecreation ofsoot,follow
theinstructions in Cleaning and
Maintenance, page13).
10.Beforeusing furniturepolish,wax,
carpetcleaner, orsimilarproducts,
turnheateroff. Ifheated,thevapors
fromtheseproductsmaycreatea
whitepowderresiduewithinburner
boxoron adjacentwallsorfurniture.
11.Thisheaterneedsfreshairventila-
tiontorunproperly.Thisheaterhas
anOxygenDepletion Sensing (ODS)
safetyshutoff system. The ODSshuts
downthe heaterifnotenough fresh
airisavailable.See AirforCombus-
tionandVentilation, pages 5through
6If heaterkeepsshutting off, see
Troubleshooting,pages15 through 16.
12.Donotrunheater:
lWhereflammableliquidsorvapors
areusedorstored.
lUnderdustyconditions.
13.Donotusethisheatertocookfoodor
burnpaperorotherobjects.
14.Donot use thisheaterif anyparthas
beenunderwater. lmmediatelycall a
qualified servicetechnician toinspect
the roomheater andtoreplaceany
partof the controlsystem, and anygas
controlwhich has beenunder water.
WARNING
ModelsGFN2815R, GFN2817Rand
GFN2819RareequippedforNatural
gas.Fieldconversion isnot
permitted.
ModelsGFP2816R,GFP2818Rand
GFP2820Rareequippedforpropane
gas.Fieldconversion isnot
permitted.
StateofMassachusetts: The
installation mustbemadebyali-
censed plumberorgasfitterinthe
CommonwealthofMassachusetts.
Sellersof unventedpropaneornatu-
ralgas-firedsupplemental roomheat-
ersshallprovidetoeachpurchaser a
copyof527 CMR30uponsaleofthe
unit.
InthestateofMassachusetts,
unventedpropaneornaturegas-fired
spaceheatersshallbeprohibitedin
bedroomsandbathrooms.

4
SAFETYINFORMATION
Continued
15.Turnoff andunplugheater andlet
coolbeforeservicing.Onlya
qualifiedserviceperson should
serviceand repairheater.
16.Operatingheateraboveelevations
of4,500 feetcouldcausepilot
outage.
17.Donotoperateheaterif anylogis
broken.Donotoperateheaterifany
logischipped(dime-sizedor
larger).
18.Topreventperformance problems,
do notuse propane/LPfueltankof
lessthan100lbs.capacity.
LOCALCODES
lnstall anduseheaterwithcare.
Followall localcodes.Inthe
absenceoflocalcodes,usethe
latesteditionofThe NationalFuel
GasCode,ANSIZ223.1,also known
asNFPA 54*.
*Availablefrom:
AmericanNationalStandards
lnstitute,lnc.
1430 Broadway
NewYork,NY10018
NationalFireProtection
Association,lnc.
BatterymarchPark
Quincy.MA02269
Thisheater isdesigned forvent-free
operation.Stateand localcodesin
someareasprohibittheuse of
vent-freeheaters.
UNPACKING
1. Removetopinner pack.
2. Tilt cartonso thatstove isupright.
3.Removeprotectiveside packaging.
4.Slidestove outof carton.
5.Removeprotective plasticwrap.
6. Removetwoself-tapping screwson
thescrew,thenliftand pulling
forward.
7.Removelogsetbycuttingplastic
ties.
8. Carefullyunwraplog.
9. Checkforanyshipping damage.If
stoveorlogisdamaged,promptly
informdealerwhereyoubought
stove.
PRODUCTFEATURES
SAFETYPILOT
Thisheaterhas apilotwithan
Oxygen Depletion Sensing (ODS) safety
shutoffsystem.TheODS/pilotisare-
quiredfeatureforvent-freeroom
heaters.TheODS/pilotshutsoffthe
heaterif thereisnot enoughfresh air. PRODUCTIDENTIFICATION
Figure1- Vent Free LP/NG Gas Stove
WATERVAPOR:ABY-PRODUCTOFUNVENTEDROOMHEATERS
Watervaporisaby-product ofgas combustion.Anunventedroomheaterproducesapproximatelyone (1)ounce
(30ml) ofwaterfor every1,000 BTU s(.3KW s)of gasinput per hour.
Unventedroomheatersarerecommendedassupplementalheater (aroom). Ratherthanaprimaryheatsource
(anentirehouse). Inmost supplementalheat applications,the watervapor does notcreateaproblem.Inmost
applications, the water vaporenhances the lowhumidityatmosphereexperienced duringcoldweather. The following
stepswill helpinsurethatwatervapordoesnotbecomeaproblem.
1.Besurethe heaterisasizedproperlyfor the application,including amplecombustionairandcirculationair.
2.Ifhighhumidityisexperienced,dehumidifiermaybeusedtohelplower the water vapor contentof theair.
3.Donot use an unventedroomheater astheprimaryheatsource.
OVERRIDECONTROL
SYSTEM
Thesefireplaceshavetwooperation
method:RemoteControlandManual
Control.TheRemoteControlhas a
transmitter,which requires three AAA
batteriesandelectricpoweroutletto
operate.Ifno power,youcanoperate
the fireplacebymanual.

5
AIRFORCOMBUSTIONAND VENTILATION
WARNING:Thisheater
shallnotbeinstalledinaconfined
spaceorunusuallytightconstruc-
tion unlessprovisions areprovided
foradequatecombustion andven-
tilation air. Readthe following in-
structionstoinsureproperfresh
airforthisand otherfuel-burning
appliances inyourhome.
PROVIDING ADEQUATE
VENTILATION
Thefollowing areexcerptsfrom
NationalFuelGasCode, NFPA24/
ANSIZ223.1.Section 5.3, Airfor
Combustionand Ventilation.
Allspacesinhomesfall intooneof
thethreefollowingventilation
classifications:
1. UnusuallyTightConstruction
2.UnconfinedSpace
3.ConfinedSpace
Theinformationon pages5through6
willhelpyou classifyyour spaceand
provide adequateventilation.
Confined and Unconfined Space
TheNationalFuelGasCode,ANSI
Z223.1 defines aconfinedspaceasa
spacewhosevolumeislessthan 50
cubicfeetper1,000 Btuperhour
(4.8m3 perkw)oftheaggregate
inputrating ofallappliancesinstalled
inthatspaceand anunconfining
spaceasaspacewhosevolumeis
notless than50 cubicfeet per 1,000
Btuperhour(4.8m3perkw)ofthe
aggregateinput rating of all appliances
installed inthatspace.Rooms
communicating directlywiththespace
inwhich theappliances areinstalled*,
through openingsnot furnishedwith
doors,areconsideredapartofthe
unconfinedspace.
Thisheatershall notbeinstalledin
aconfinedspaceorunusuallytight
constructionunlessprovisionsare
providedforadequatecombustion
andventilationair.
*Adjoining roomsarecommunicating
onlyiftherearedoorless passage-
waysorventilation grillsbetween
them.
UnusuallyTightConstruction
DETERMINING FRESH-AIRFLOWFORHEATERLOCATION
Determining ifYouHave aConfined orUnconfined Space
Usethisworksheet todetermine if youhave aconfinedorunconfinedspace.
Space: Includesthe roominwhichyouwillinstallheaterplus anyadjoiningroomswithdoorlesspassageways
or ventilation grillsbetweentherooms.
1. Determinethe volumeofthespace(length×width×height).
Length×Width×Height= cu.ft. (volumeofspace)
Example: Spacesize 20ft.(length)×16ft.(width)×8ft. (ceilingheight)=2560cu. ft.(volumeofspace)
Ifadditionalventilationtoadjoiningroomissupplied withgrillsor openings, addthevolumeofthese
roomstothetotal volumeofthespace.
2.Dividethespacevolumeby50 cubicfeettodeterminethemaximumBtu/Hrthespacecansupport.
(volumeofspace) 50 cu.ft.=(MaximumBtu/Hr the spacecansupport)
Example: 2560 cu.ft. (volumeofspace) 50cu.ft.=51.2or 51,200(maximumBtu/Hrthe spacecansupport)
Theair that leaks arounddoorsand
windowsmay provideenoughfresh
airforcombustionandventilation.
However, inbuildingsofunusuallytight
construction,you mustprovide
additionalfresh air.
Unusuallytightconstruction is
definedasconstruction where:
a) wallsand ceilingsexposedtothe
outsideatmospherehavea
continuouswatervaporretarder
witharating of oneperm(6×10-11 kg
perpa-sec-m2)orless with
openingsgasketedorsealed and
b)weatherstrippinghas been added
onwindowsthatcanbe opened
anddoors and
c) caulkingorsealantsareapplied
toareas such as jointsaround
windowanddoorframes, between
soleplates and floors,between
wall-ceiling joints,between wall
panels,atpenetrationsfor
plumbing,electrical,and gas
lines, andatother openings.
If yourhomemeetsall ofthe three
criteriaabove,you mustprovide
additionalfreshair.See VentilationAir
FromOutdoors(page6).
Ifyourhomedoes notmeetall ofthe
three criteriaabove,proceedto
DeterminingFresh-AirFlowFor
HeaterLocation(below).

6
WARNING:Reworkworksheet, adding
thespaceoftheadjoiningunconfined
space. Thecombinedspacesmusthave
enoughfreshair tosupplyallappliances in
bothspaces.
If the actualBtu/Hrusedislessthanthe maximumBtu/Hrthespace can support,the spaceisan
unconfined space.Youwill need noadditional freshairventilation.
3. AddtheBtu/Hrof all fuelburning appliances inthe space.
Vent-free heaterBtu/Hr
Gaswaterheater* Btu/Hr
GasfurnaceBtu/Hr
Ventedgas heaterBtu/Hr
Gasheaterlogs Btu/Hr
Othergas appliances*+Btu/Hr
Total=Btu/Hr
*Donotincludedirect-ventgas appliances.Direct-ventdrawscombustion airfromtheoutdoorsand
ventstotheoutdoors.
4. Comparethe maximumBtu/Hrthespacecan supportwiththeactualamountofBtu/Hr used.
Btu/Hr(maximumthespace can support)
Btu/Hr(actualamount ofBtu/Hrused)
Example : 51,200Btu/Hr(maximumthe spacecansupport)
56,000 Btu/Hr (actualamount of Btu/Hr used)
Thespaceintheaboveexampleisaconfinedspacebecause theactualBtu/Hrused ismorethan the
maximumBtu/Hrthespace cansupport.
Youmust provideadditionalfresh air. Your options areas follows:
A.Reworkworksheet, adding thespaceof an adjoining room. Iftheextraspaceprovidesanunconfined
space,removedoortoadjoining roomoradd ventilation grillsbetweenrooms. See Ventilation AirFrom
InsideBuilding (below).
B.Vent roomdirectlytothe outdoors.See VentilationAir FromOutdoors (below).
C. InstallalowerBtu/Hrheater,if lowerBtu/Hrsizemakesroomunconfined.
Figure2-Ventilation AirfromInsideBuilding
Example:
Gas water heater 30,000 Btu/Hr
Vent-free heater + 26,000 Btu/Hr
Total=56,000 Btu/Hr
WARNING:If thearea inwhich theheatermaybeoperated issmallerthanthatdefinedas anunconfined
spaceorif the buildingisofunusuallytightconstruction,provideadequatecombustionandventilationairbyone
of themethodsdescribed intheNationalFuelGas Code, ANSI Z223.1, Section5.3 orapplicablelocalcodes.
Thisfreshairwouldcomefromanadjoining uncon-
finedspace.Whenventilatingtoanadjoininguncon-
fined space,you must providetwopermanentopenings:
one within12"oftheceiling andonewithin12"of the
flooron the wallconnecting the twospaces(see
options1and2,Figure2). Youcanalsoremovedoor
intoadjoiningroom(seeoption3,Figure2). Followthe
National Fuel Gas Code.NFPA24/ANSI Z223.1, Sec-
tion 5.3,AirforCombustionand Ventilation forre-
quiredsize of ventilation grillsorducts.
Ventilation AirFromlnside Building
Ventilation AirFromOutdoors
Provide extrafreshair byusingventilationgrillsor ducts.
You mustprovidetwopermanentopenings:onewithin
12"of theceiling and onewithin12"of thefloor. Connect
these itemsdirectlytotheoutdoorsor spaces opentothe
outdoors. Thesespaces includeatticsandcrawlspaces.
Followthe NationalFuelGasCode,NFPA24/ANSI
Z223.1, Section5.3,Air forCombustion andVentilation
forrequiredsizeofventilationgrillsor ducts.
IMPORTANT: Donotprovideopenings forinletorout-
letairintoatticif attichas athermostat-controlled
powervent. Heated airentering the atticwill activate
the powervent.
Figure3-Ventilation AirfromOutdoors

7
NOTICE: Thisheateris
intended foruse as supplemen-
talheat.Use thisheateralong with
yourprimaryheating system.Do
notinstallthisheateras your
primaryheatsource.If you have
acentral heating system,you
mayrunsystem'scirculating
blowerwhileusingheater. This
will helpcirculatethe heat
throughoutthe house.
INSTALLATION
WARNING: Aqualifiedservice
personmustinstallheater.Follow
alllocalcodes.
WARNING: Neverinstall the
heater
l inabedroomorbathroom
l inarecreationalvehicle
l wherecurtains,furniture,clothing,
orother flammableobjectsare
lessthan42 inches fromthe
front, top, or sides of theheater
l inhightrafficareas
l inwindyor draftyareas
WARNING: Maintainthemini-
mumclearances.If youcan, pro-
vide greater clearancesfromfloor,
ceiling,and adjoining sideand
backwalls.
CAUTION: Thisheater creates
warmaircurrents.Thesecurrents
moveheat towall surfaces nextto
heater. Installing heater nexttovinyl
orclothwallcoveringsoroperating
heaterwhereimpurities (suchas
tobacco smoke,aromaticcandles,
cleaning fluids,oil orkerosene lamps,
etc.)intheairexist,maydiscolor
walls.
IMPORTANT: Vent-freeheatersadd
moisturetothe air. Althoughthisis
beneficial,installingheaterinrooms
withoutenoughventilationairmay
cause mildewtoformfromtoomuch
moisture.See AirforCombustion and
Ventilation,pages5through6.
CHECK GAS TYPE
Use onlythetypeofgas indicatedon
theplate.If yourgassupplycan not
meetthatrequirement,donotinstall
heater.Callthe dealerwhereyou pur-
chasedheater, forthe propertype of
heater.
Figure4-MinimumClearance toWall and Ceiling
CLEARANCESTOCOMBUSTIBLES
(Vent-FreeOperation Only)
Carefullyfollowtheinstructionsbelow.
Thisfireplaceisafreestandingunit
designedtoset directlyonthefloor.
IMPORTANT:You mustmaintain
minimumwallandceilingclearances
duringinstallation.The minimum
clearances areshowninFigure4.
Measurefromoutermostpoint of stove
top.
MinimumWallandCeilingClearances
(seeFigure4)
A. Clearances fromoutermost point
of stovetop toanycombustibleside
wall shouldnotbeless than12
inches.
B. Clearancesfromthestovetopto
the ceiling shouldnotbelessthan
48inches.

8
CONNECTING TO GAS
SUPPLY
WARNING: Aqualifiedservice
person mustconnect heater togas
supply. Followall localcodes.
CAUTION: Neverconnectheater
directlytothegas supply.This
heaterrequiresan externalregula-
tor(notsupplied). lnstalltheexter-
nalregulatorbetweentheheater
andgassupply.
INSTALLATION ITEMSNEEDED
Beforeinstalling heater,makesure
youhavethe itemslisted below.
l piping(check localcodes)
lsealant(resistanttopropane/LPgas)
lequipmentshutoff valve*
ltestgauge connection**
lsedimenttrap
ltee joint
lpipewrench
lFlexibleGas hose(check localcode)
*ACSAdesign-certified equipment
shutoff valvewith1/8" NPTtapis
anacceptablealternativetotest
gaugeconnection.Purchasethe
optionalCSA design-certified
equipmentshutoffvalvefromyour
dealer. SeeAccessories.
Figure5-Gas RegulatorLocation
and Gas Line Access IntoStove
Cabinet
Figure6- External RegulatorWith
VentPointing Down
Figure7-GasConnection
Theinstallermustsupplyanexternal
regulator.Theexternalregulatorwill
reduceincoming gas pressure.You
must reduce incominggaspressure
tobetween11and 14 inches of water.
Ifyou do notreduceincoming gas
pressure,heaterregulatordamage
couldoccur. lnstallexternalregulator
withthe vent pointingdownasshown
inFigure6.Pointing theventdown
protectsitfromfreezing rainor sleet.
*PurchasetheoptionalCSAdesign-certifiedequipment shutoffvalve
fromyourdealer.See Accessories.
**Minimuminletpressureforpurposeof input adjustment.
NGModels:
5”to10.5”W.C.
Gassupplierprovideexternal
regulatorfornaturalgas
INSTALLATION
Continued
WARNING: Never connectheater
toprivate(non-utility)gaswells.
Thisgasiscommonlyknownas
wellhead gas.
FrontView
CAUTION: Onlyuseanewblack
iron orsteelpipe.Internally-tinned
coppertubing maybeusedin
certainareas.Check you local
codes. Usepipeof1/2"diameteror
greater toallowproper volumegas
toheater. If pipeistoo small, undue
lossofpressurewill occur.
Installationmustinclude anequip-
mentshutoff valve,union,and
plugged 1/8"NPTtap. LocateNPT
tap withinreach for testgauge hook
up.NPTtap mustbe upstream
fromheater(seeFigure7).
IMPORTANT:Install equipment
shutoff valveinan accessiblelocation.
The equipmentshutoff valve isfor
turning on or shutting off thegasto
theappliance.Applypipejointsealant
lightlytomalethreads. Thiswillpre-
ventexcess sealantfromgoing into
pipe.Excesssealantinpipecould
result incloggedheatervalves.
CAUTION: Usepipe jointsealant
that isresistant togas(PROPANE
or NG).
Werecommendthatyouinstalla
sedimenttrapinasupplylineas
showninFigure7.Locatesediment
trapwhereitiswithinreachforcleaning.
Install inthepiping systembetween
fuelsupplyandheater.Locatesedi-
menttrapwheretrappedmatter isnot
likelytofreeze. Asediment traptraps
moistureand contaminants.This
keepsthemfromgoing intoheater
controls.Ifsedimenttrapisnotin-
stalledorisinstalledincorrectly,
heatermay notrun properly.
CAUTION: Avoiddamage to
regulator. Holdgas regulatorwith
wrench whenconnectingintogas
pipingand/orfittings.
Purchase

9
WARNING: Neveruseanopen
flametocheckforaleak.Applya
mixtureofliquidsoap andwater to
alljoints.Bubblesformingshowa
leak.Correctall leaksimmediately.
CAUTION: Makesureexternal
regulatorhasbeeninstalledbe-
tweengassupplyand heater. See
guidelines under Connecting toGas
Supply (page8).
Figure8-EquipmentShutoff Valve
PressureTestingGas
SupplyPipingSystem
Test Pressures InExcessOf 1/2
PSIG(3.5kPa)
1.Disconnect heaterwithitsappliance
maingas valve(controlvalve)and
equipment shutoffvalve fromgas
supplypipingsystem.Pressures
inexcess of 1/2psigwilldamage
heaterregulator.
2.Capoffopen endofgaspipewhere
equipmentshutoffvalvewas
connected.
3.Pressurize supplypiping system
byeitherusingcompressedairor
openinggassupplytankvalve.
4. Checkall jointsof gas supply
piping system.Applymixtureof
liquidsoap and watertogas joints.
Bubbles formingshowaleak.
5.Correctall leaksimmediately.
6.Reconnectheaterand equipment
shutoff valvetogas supply.Check
reconnectedfittingsforleaks.
PressureTesting Heater
Gas Connections
1. Openequipment shutoff valve(see
Figure8).
2. Open gassupplytankvalve.
3.Make surecontrolknobofheateris
intheOFFposition.
4.Checkalljointsfromequipment
shutoff valvetocontrol valve(Figure
9).Applymixtureofliquidsoapand
watertogasjoints.Bubblesform-
ingshowaleak.
5.Correctallleaksimmediately.
6. Lightheater(see OperatingHeater,
page 10). Checkall otherinternal
jointsfor leaks.
7.Turnoffheater (see Operationof
Turn-Off , page10).
Figure9-Checking Gas Joints
CHECKINGGASCONNECTIONS
WARNING: Test allgas piping
and connectionsforleaksafter
installing orservicing.Correctall
leaksimmediately.
INSTALLATION
Continued
TestPressuresEqualToor
LessThan1/2PSIG(3.5kPa)
1. Close equipment shutoffvalve(see
Figure8).
2.Pressurize supplypiping system
byeitherusing compressedairor
openinggassupplytank valve.
3.Check all jointsfromgas meterto
equipmentshutoff valve (seeFigure
9).Applymixtureofliquidsoapand
water togas joints.Bubblesform-
ingshowaleak.
4.Correct allleaksimmediately.

10
WARNING: Failuretoposition
thepartsinaccordance withthese
diagramsmayresultinproperty
damage orpersonalinjury.
CAUTION: Afterinstallationand
periodicallythereafter,checktoen-
surethatnoflamecomesin
contact withanylog.Withthe heater
set toHigh, check toseeifflames
contact anylog. If so, reposition logs
according totheloginstallation
instructions inthismanual.Flames
contacting logs willcreatesoot.
Figure10 -Installing Log Set(Top
View)
INSTALLATION
Continued
INSTALLINGLOGS
IMPORTANT: Makesurelog does not
cover anyburner ports(see Figure10).
Also,see logplacing instructions,
pages22
OPERATINGHEATER
FOR YOUR SAFETY
READ BEFORELIGHTING
A. Thisappliance has apilot which
must belighted bycontrolsystem,
Whenlighting thepilot,follow
theseinstructionsexactly.
B.BEFORELIGHTINGsmellall
aroundthe appliance areafor
gas.Besuretosmell nexttothe
floorbecause somegas is
heavierthanairand will settle
on thefloor.
WHATTODOIFYOUSMELL GAS
SEE WARNINGinPage1for proper
instructions.
Fig12 Front of the Transmitter
NOTICE: During initialopera-
tion of newfireplace,burninglogs
will giveoff apaper-burning smell.
Orangeflamewill also be present.
Openawindowtovent smell. This
willonlylastafewhours.
CAUTION: Donot trytoadjust
heatinglevelsbyusingthe
equipment shutoffvalve.
LIGHTINGINSTRUCTIONS
Note:If operatingbytransmitter,you
mustsetthecontrolknobonELECTRIC
position. Donotsetthe control knob
betweenthe locked position,
otherwisetherewill be nopowerto
the heater
1. STOP!Readthesafetyinformation,
page 3.
2.Makesureequipmentshutoff valve
isfullyopen.
Figure-11Manual ON/OFF Button
and ON/OFFSwitchlocation
C.Useonlyyourhandtopushin
controlknob.Neveruse tools.Ifthe
appliancecouldnotoperate,don'ttry
torepair it,Callaqualifiedservice tech-
nicianorgas supplier.Forcedorat-
temptedrepairmay resultinafireor
explosion.
D. Donot use thisapplianceif any
part hasbeen under water. Imme-
diatelycall aqualifiedservicetechni-
ciantoinspect theapplianceandto
replaceanypart ofthecontrolsystem
and anygascontrol whichhas been
underwater.
TOTURNOFF GASTOAPPLIANCE
Shut off heater
1. Pressthe IGN/OFFbutton.(See fig-
ure12)
2.Set the Switchon OFF location.(See
figure11)
Shuttingoff burneronly( pilotstaylit)
1.Press theBURNER toset flameOFF
select
WARNING: Ifyou do notfollow
these instructionsexactly,afireor
explosion may resultcausingprop-
ertydamage,personalinjuryor loss
oflife.
Note: Tooperateyour heatertheON/
OFFswitch mustbeinthe ON
position.TheREDlightindicates
thereiselectrical power toyour heater
whentheON/OFF switch isintheON
position. TheGREEN lightindicates
the pilot lightisON.
Note: Pleasewaitforone minute
tolightagainaftershuttingoff
heater.
FunctionofManualON/OFFButton
andPowerON/OFF Switch
If your remotetransmitter islost or does
notfunction,you canpress the
ManualON/OFF Button inorderto
manuallyoperateyourheater.

11
b.manual selectofmain
burner:
PressBURNERbutton,theflame
ison “MAN”select.Atthisselection,
the mainburnerwill keepworking no
matterwhatthe temperatureissetat.
If thereisaneed toshut off the main
burner, justpress the “BURNER”
button tomaketheburneron the
“OFF”select.
c.shutoff themainburner:
themainburner ison “OFF”selection,
The mainburnerwillshutoff.
nOPERATIONSOFn
TIMING
1.Autoon:
when theburner isinastateof
readiness.Transmitterand burneris
off. Press TIMER button. Thenpress
or ▼changetothescheduledtime,
thenpresstheTIMER button again, the
TIMERstartstimingand theTIMER is
flashingandtheoperationlight(green)
beginflashing.When thetimergoes
onthescheduled time,the burner
opensautomatically.
2.Autooff:
whentheburnerisinoperation, press
TIMERbutton.Thenpress or ▼to
changetothescheduledtime,then
press theTIMER button again,the
TIMERstartstimingand theTIMER is
flashingandtheoperationlight(green)
beginflashing.When thetimergoes
onthescheduled time,the burner
closes automatically.(SeeFig14)
nOPERATIONSOFn
BURNER
1.Plug-in110Velectricaloutlet, you will
hear ahighpitchsoundandpower light
(red) on thedoor will belit that indicates
that theburner isreadytobe operated.
Beforepluggingintheoutlet makesure
thattheapplianceisconnectedtothe
gassupply,thencontinuetothe next
step.
2.Point directlytheremotetransmitterto
theburner. Press ING/OFF button,the
electricsparkstartsignitingthe pilotand
operation light(green)on thedoorwill
be lit.Waitfive(5) minutes toclear out
anyair. Ifyousmellgas.STOP!Please
checkthe gasconnection.
Therearethreeselections: “AUTO”
“MAN”and “OFF”
a.autoselectofmainburner:
PressBURNERbutton,theflame is
on “AUTO”select.Press or ▼toset
temperature.If the roomtemperatureis
twodegreelowerthan the settempera-
tureon the remote,themainburner will
turnonuntilthe surroudingtemperature
istwodegree higherthantheset
temperature. Onceitreaches tempera-
tureon the remoter, the mainburner will
automaticallyshutoff.
(Note:ontheautoselect of main
burner,the mainburnerdoesnot
respond immediatelytotheset
temperatureuntilaboutone minute
later.)
Fig 15 -Control board
Fig13 Back ofthe Transmitter
nOPERATIONSOFn
REMOTETRANSMITTER
1.Installthree DC1.5batteriesinthe
batteryholder.
Theinitialstart-upontheLCDis: SET
TEMPis77°F,ROOM TEMPis77°F,
clock isAM12:00,burnerison “OFF”
select, and fanison “AUTO”select.Di-
videPointsofhourand minuteareflash-
ing(i.e. thetimerisoperating).
2.Clock setting:Press CLOCKbutton
on theremotetransmitterpaneltose-
lectitem(hour, minute). Theselected
itemisflashing.Press or ▼to
changetothecorrectactualhour(s);
Press or ▼tochangetothe correct
minute(s), then pressCLOCKbutton
again,timesetting isfinished.
3. Wheninoperation, point theremote
transmittertotheremotereceiver on the
burnerinamaximumdistanceof20
feetwithoutanyobstructionbetween
them.
Fig14 Initialstart-up onthe LCD
Fig16 AUTO”select
OPERATINGHEATER
Continued
Note: The thermostatsensing bulb
measuresthetemperatureofair
neartheheatercabinet. Thismay
notalwaysagree withroom
temperatureorthetemperatureon
transmitter:theidealcomfortsetting
willvary,thatdepends on housing
constructioninstallation,roomsize,
openairtemperature,etc.

12
nTOTURNOFFn
GASTOAPPLIANCE
Shutting Off Heater
Turncontrolknobclockwise tothe
OFFposition.
Shutting OffBurnerOnly( pilotstays
lit)
Turncontrolknobclockwise tothe
PILOT/IGNposition.
NOTE: If power ison,youcanoperate
thefireplacebytransmitter.Pressin
and rotatecontrolknob clockwise
toELECTRICpositionaftershutting off
thefireplace.
nMANUALLIGHTINGn
PROCEDURE
1.Followsteps1through5under
LightingInstructions.
2.Withcontrolknob pressedin, strike
match.Holdmatchtopilot until pilot
lights.
3.Keepcontrolknob pressedinfor30
seconds afterlightingpilot. After 30
seconds,releasecontrolknob.Fol-
lowstep8under Lighting
Instructions.
4. Aftercompletionoftheabove-men-
tionedthree steps,thetransmitter
iskeptinastateofreadiness. If the
appliancedoesn tworkingforape-
riodtime, justpull out the plugfrom
the110Velectricaloutlet.
nLIGHTINGn
INSTRUCTIONS
Figure16 Manual Control
If powerisoff, you can operatethe
fireplace bymanual
1.STOP!Read thesafetyinformation
ontheplatewithheater.
2.Check thatgas supplytoheateris
on.
3.Remove the dooron theright panel.
4.Pushingascontrol knobslightlyand
turnclockwise totheOFF
position. If Control Knob ison ELEC-
TRICposition,pressdownthe Con-
trolKnob and rotatecounter clock-
wise toOFFposition.
NOTE:Knobcannot beturnedfrom
“PILOT”to “OFF”unless knob is
pushedinslightly.Donotforce.
5.Wait five(5)minutes toclearout
anyair. Thensmell forgas,in-
cludingnearthefloor.Ifyousmell
gas, STOP!Follow “B”inthesafety
informationonthe side ofthe
heater. If you donot smellgas,go
tothenextstep
6.Push ingas controlslightlyand
turncounterclockwise to “PI-
LOT”and depressforfive(5)
seconds.
NOTE:Thefirsttimethatthe
heaterisoperatedafterconnect-
ing thegas supply,thecontrol
knobshouldbedepressedfor
about thirty(30) seconds.Thiswill
allowairtobleed fromthe gas
system.
7. Withcontrolknobpressed in, push
downand releasetheignitor
button.Thiswilllightpilot.If
needed,keeppressing ignitor
buttonuntilpilotlights.
8.Keep controlknob depressedfor
ten (10)secondsafterlighting
pilot. If pilot goesout, repeat steps
5,6and7.
9.Toturnonmainburnerpartially
press downthe controlknob
slightlyandrotatecounterclock-
wise . Releasethe downward
pressureon theknobwhilecon-
tinuingtoturnuntil theknoblocks
atthe “ON”desiredsetting
position.Donotoperatebetween
lockedpositions.
nOPERATIONSOFn
TURN-OFF
1.Manualturn-off:when theheater is
inoperation, presstheING/OFF but-
tontoshutofftheheater.
2.Autoturn-off: refertothe second
step of “Operationsof Timing”
3.Aftercompletionofthe abovemen-
tionedtwosteps,thetransmitteris
keptinastateofreadiness.If the
appliance doesn tworkingfor ape-
riodtime,justpull outtheplugfrom
the110Velectricaloutlet.
nOPERATIONSOFn
KEY-PRESSLOCKING
1.Keypresslocking:
whentheburnerisinoperationor the
transmitterisinastateofreadiness,
justpressLOCKbuttonontheoperat-
ingpanel,therewill bea “ ” symbolon
theLCD.If anybuttonispressed now,
the burnerwillnotreact atall.
2.Key-press unlocking:
whentheburnerisinastateofkey-
presslocking, firstpress ▼, thenpress
LOCK buttontounlockit (Childproof-
SeeFig16)
nOPERATIONSOFn
FAN
Therearethree selections: “AUTO”
“MAN”and “OFF”.Whenpushing the
“FAN”buttonon the “AUTO”select, the
fanwillbe controlled bythe thermostat
on thefanblowerunit. Onthe “MAN”
select, thefan willbe kept inoperation.
Tostop theoperation,pushthe “FAN”
buttonto “OFF”select. (SeeFig16)
ManualControl System
Weprovidethemanual controlsys-
temjustincase of powershortage.
InstallbatteryforManual Ignitor:
1.Unscrewthe ignitor cap.
2.Insert aAAAtypebatterywithitsan-
ode(“+”)pointingout.
3.Screwthe ignitorbackcap.
Note: Werecommendthatthebattery
betaken outoftheignitorwhen the
powersupplygetsright.

13
Figure17 - Correct Pilot Flame
Pattern
OPERATINGHEATER
Continued
INSPECTINGBURNERS
Checkpilotflamepatternand
burnerflamepatternsoften.
PILOTFLAMEPATTERN
Figure17showsacorrectpilot
flamepattern.Figure18showsan
incorrectpilotflamepattern.The
incorrectpilotflameisnot touching
the thermocouple.Thiswill causethe
thermocoupletocool.Whenthe
thermocouplecools,theheater
will shutdown. If pilot flamepatternis
incorrect, asshowninFigure14
lTurnheater off(see OPERATIONOF
TURN-OFF, page9)
lseetroubleshooting, page15.
Figure18 - Incorrect Pilot Flame
Pattern
Figure19showsacorrectburner
flamepattern.Figure20showsan
incorrectburnerflamepattern.If
burnerflameisincorrect:
lTurnheater off(see OPERATIONOF
TURN-OFF, page 10)
lseetroubleshooting, page15.
BURNERFLAMEPATTERN
Figure19 -CorrectFlamePattern
withControlKnobSet toHighFlame
Figure20-IncorrectFlamePattern
withControlKnobSet toHighFlame
Figure21-InjectorHolderOnOutlet
BurnerTube
WARNING: Disconnect power be-
foreattempting anymaintenanceor
cleaningtoreduce the riskoffire, elec-
tricshookorpersonalinjury.Turnoff
heater and let coolbeforecleaning.
CLEANINGAND MAINTENANCE
DISCONNECT WIRINGOR CONTROL
MODULE
1.Removefourscrewsfromtherear
controlpanel,takeout thermostat
sensingbulbfromtheclip,then disco-
nnectthewirestofree tocontrol
modulefromitsmounting location .
Note:Donotconfusethe markon
the eachwire.
2.Removetwoscrewsand hex nuts,
take outthe controlmodule.Whenin-
stalling , reverse thestepsabove.
(SeeFigure22andFigure25)
Figure22- ControlModel
DISCONNECTFAN
1. Remove screwsfromthefanbracket
panel,pull thefanbracket panelout to
remove.Thendisconnecttwowires
free tofan.
2.Markortageachwireremovedfor
itsexact reconnection.Removethefour
screwsfromthefan .wheninstalling ,
reverse thestepsabove.(SeeFigure
23andFigure25)
Figure23-Fan
CAUTION:Label all wires prior todis-
connection whenservicingcontrols.
Wiring errorscancauseimproper
anddangerousoperation.Verify
properoperationafterservicing.

14
Cleanthe pilot assemblyalso. Ayellow
tiponthe pilotflameindicatesdustand
dirtinthepilotassembly.Thereisa
smallpilotairinletholeabouttwo
inchesfromwherethe pilotflame
comes outofthe pilotassembly(see
Figure24). Withtheunit off, lightlyblow
airthroughtheairinlethole. You may
blowthrough adrinking strawifcom-
pressedairisnotavailable.
CLEANING ANDMAINTENANCE
Continued
Figure24 -Pilot AirInlet Hole
CABINET
AirPassageways
l Useavacuumcleanerorpressur-
ized airtoclean.
Exterior
l Useasoft clothdampenedwitha
mildsoapand watermixture. Wipe
the cabinet toremove dust.
LOGS
l If youremovelogsfor cleaning,
referto InstallingLogs (page10)
toproperlyreplace logs.
l Replacelogs if broken or chipped
(dime-sizedorlarger).
MAINBURNER
Periodicallyinspectall burnerflame
holes withtheheaterrunning.All
slottedburnerflameholes should
be open withyellowflamepresent. All
roundburnerflameholesshouldbe
open withasmallblueflame
present.Someburnerflameholes
may becomeblockedbydebrisor
rust,withnoflamepresent. Ifso,
turnoffheaterandletcool.Either
removeblockageorreplaceburner.
Blockedburnerflameholes will
createsoot.
CAUTION: Youmustkeep
controlareas,burner,and
circulatingairpassagewaysof
heaterclean.Inspectthese
areas ofheaterbeforeeach
use.Haveheaterinspected
yearlybyaqualifiedservice person.
Heatermayneed more
frequentcleaning dueto
excessivelintfromcarpeting,
beddingmaterial, pethair, etc.
CLEANING ODS/IGNITOR AND
BURNER
Cleanwithavacuumcleaner.
CLEANINGBURNER
INJECTOR HOLDERAND
PILOTAIRINLETHOLE
Werecommendthatyou cleantheunit
everythree monthsorafter 2500hours
ofoperation. Wealso recommendthat
youkeep the burner tube and pilot as-
semblycleanandfree of dustand
dirt. Tocleanthese partswerecom-
mendusing compressedairnogreater
than30PSI.You canuseavacuum
cleanerintheblowposition.Ifusing
compressed airinacan,please fol-
lowthedirectionsonthecan.If you
don't followdirectionsonthe can,you
coulddamagethepilotassembly.
1.Shutoff the unit, including thepilot.
Allowthe unit tocool foratleastthirty
minutes.
2.Inspect burner, pilot andprimaryair
inlet holes on injector holder for dust
anddirt(seefigure21).
3. Blowairthrough theports/slotsand
holesinthe burner.
4. Check theinjectorholder located
attheendoftheburnertube
again.Removeanylarge particles
ofdust,dirt, lint, orpethairwitha
softclothorvacuumcleaner
nozzle.
5.Blowairintotheprimaryairholes
onthe injector holder.
6.Incaseanylarge clumps ofdust
havenowbeenpushedintothe
burner, repeat steps 3and4.
Figure25- -OverrideControlSystemDiagram

15
OBSERVEDPROBLEM POSSIBLECAUSE REMEDY
1. Thermocoupleconnectionloose at
controlboard
2. Pilotflamenottouchingthermo-
couplewhich allowsthermocouple
tocool, causing pilot flametogo
out. Thisproblemcouldbecaused
byoneorbothofthefollowing
A)Lowgas pressure
B) Dirtyor partiallycloggedODS/
pilot
3.Thermocoupledamaged
4. Controlvalvedamaged
1. Hand tightenuntilsnug, thentighten
1/4turnmore.
2.A)Contactlocalpropane/LPgas
company.
B) CleanODS/pilot (seeCleaning
and Maintenance,page13)orre-
placeODS/pilotassembly
3.Replacethermocouple
4. Replacecontrol valve
Burnerdoesnotlight after ODS/pilot
islit
1.Burner orifice clogged
2.Inletgaspressureistoolow
3.Burner orificediameteristoo small
4. Thermocoupleleadsdisconnected
orimproperlyconnected
5. Burnerswill notcomeinremote
position
1.Cleanburner(see Cleaningand
Maintenance,page13)orreplace
burnerorifice.
2.Contact localpropane/LPgascom-
pany
3.Replace burner orifice
4.Reconnectleads(see wiring
diagram)
5.Replace batteryintransmitter and
receiver
ODS/pilot lightsbutflameis
continuousigniting andthemain
burner couldn t belit.
TROUBLESHOOTING
WARNING:Make surethatpower
isturnoff beforeproceeding....
WARNING: Turnoffandletcool
beforeservicing.Onlyaqualified
servicepersonshouldservice and
repairfireplace.
CAUTION:Neveruseawire,
needle,orsimilarobject toclean
ODS/pilot. Thiscan damage ODS/
pilotunit.
Whenpressing thebutton ofignitor
buttonispressed,thereissparkat
ODS/pilot butnoignition
1.Gassupplyturnedoff orequipment
shutoffvalveclosed
2. Airingas lineswhen installed.
3.Depletedgas supply
4. ODS/pilotisclogged
5.Gasregulator settingisnotcorrect
6.Pilot electrodeposition isnotcorrect
7. Wireisnot correct orloosen
8Gas valveisdamage
1.Turnon gas supplyoropen equip-
mentshutoffvalve
2.PressON/OFF button againuntil air
isremoved .
3.Contactlocalpropane/LPgascom-
pany
4Clean ODS/pilot (seeCleaning and
Maintenance,page 13 )orreplace
ODS/pilotassembly
5.Replace gascontrol
6.Replace Pilot
7.Check the wineandmake wine
correct.
8.Replacegasvalve
Nosparkwhenpress inignition button1. Nopowertoheater
2.Nobatteryintransmitter orbattery
isn tcorrectlyassembly
3. Systemhalt
1. Checkthe electricpower
2. Place or replace thebattery.
3.Placethe controlknob ofmanual
overrideon OFFposition forat
least1minute,then turntoELEC-
TRICposition
NOTE:BEFOREYOU SWITCH TO “ELECTRIC”CONTROLLEVEL FROM MANUALCONTROL,
YOUNEED TOTURN THEKNOBTO “OFF”LEVELFIRSTAND WAITFOR ONEMINUTE,THEN
TURN THE KNOB TO “ELECTRIC”.
INCASEOF “ELECTRONIC”CONTROLLEVEL DOESNOTWORK,PLEASE TURNTHECON-
TROLKNOB COUNTERCLOCKWISE TO “OFF”LEVELANDWAITFORONEMINUTE.

16
Btu(Variable)
GasType LPGasNaturalGas
Ignition AutomaticorElectronicAutomaticorElectronic
ManifoldPressure8"W.C. 3"W.C.
InletGasPressure
(In.ofwater)*
Maximum14"10.5"
Minimum11"5"
Dimensions,Inches(H×W×D)
Heater36 1/4”×45 1/2”×12 3/16”36 1/4”×45 1/2”×12 3/16”
Carton 42”×48 9/16”×13 7/16”42”×48 9/16”×13 7/16”
Weight, lbs
Stove101 101
Shipping120 120
voltage 120120
watt3232
*Forpurposesofinputadjustment
Delayed ignition burner 1. Manifoldpressureistoolow
2. Burnerorifice clogged
1. Contactlocalgascompany
2.Cleanburner(see Cleaningand
Maintenance, page13)
Burnerbackfiringduringcombustion 1.Damaged burner
2. Gasregulatordefective
1.Clean burner orifice(seeClean-
ingandMaintenance,page 13)
2.Replace gasregulator
Slight smokeor odorduring initial
operation
1.Residues frommanufacturing
processes
2. Not enoughair
3. Gasregulator defective
1. Problemwillstopafterafewhours
ofoperation
2.Check burner fordirtand debris.
If found,clean burner(seeClean-
ingandMaintenance,page 13)
3.Replace gasregulator
Darkresidueonlogsorinsideof
fireplace
1.Improperlogplacement
2. Air holesatburner inlet blocked
3.Burnerflameholesblocked
1. Properlylocatelogs(see installing
logs,page22)
2.Cleanoutairholes atburnerinlet.
Periodicallyrepeatasneeded.
3. Remove blockageor replaceburner
Heater producesaclicking/ticking
noisejustafter burnerislit or
shut off
1. Metalexpandingwhileheatingor
contractingwhilecooling
1.Thisiscommonwithmost heaters.
If noise isexcessive, contact quali-
fied serviceperson
TROUBLESHOOTING
Continued
GFP2816RGFN2815R
GFP2818RGFN2817R
GFP2820RGFN2819R
SPECIFICATIONS

17
REPLACEMENTPARTS
NOTE: Useonlyoriginalreplacement
parts.Thiswill protectyourwarranty
coverageforpartsreplaced under
warranty.
PARTS UNDERWARRANTY
Contactauthorizeddealersofthis
product. Ifthey can'tsupplyoriginal
replacementpart(s),callKOZY-
WORLD stoll freenumberat(814)
643-1775 forreferralinformation.
WhencallingKOZY-WORLDor your
dealer, haveready:
l Yourname
l Your address
l Modelandserialnumbers
of yourheater
l Howheater wasmalfunctioning
l Typeof gasused(propane/LPor
NG)
l Purchasedate
l Warrantycard
Usually,wewillaskyoutoreturn
thedefectivepart tothefactory.
PARTS NOTUNDER
WARRANTY
Contactauthorizeddealersofthis
product. If theycan t supplyoriginal
replacementpart(s)call KOZY-
WORLD stoll free number at(814)
643-1775 forreferralinformation.
Whencalling KOZY-WORLD,have
ready
l Modelnumber of yourheater
l The replacementpart number
REPLACEMENTPARTS
ACCESSORIES
Purchasetheseheateraccessories
fromyourlocaldealer. If theycannot
supplytheseaccessories,call KOZY-
WORLD stoll freenumber at(814)
643-1775forreferralinformation.You
can also writetotheaddresslisted
onthefront pageofthismanual.
EQUIPMENT SHUTOFF VALVE
Equipmentshutoff valvewith1/8"
NPTtap.Thispart isnotcurrentlyavail-
ablefromKOZY-WORLD.
FLEXIBLEGASHOSE
l Flexiblegas hose isusedfor
connectingthe heatertogas supply.
l Theflexiblegas hosemustbe
CSA approved.

18
ILLUSTRATED
PARTSBREAKDOWN
GFN2815R
GFP2816R
GFN2817R
GFP2818R
GFN2819R
GFP2820R

19
PARTSLIST
GFN2815R
GFP2816R
GFN2817R
GFP2818R
GFN2819R
GFP2820R
Thislistcontains replaceablepartsusedinyourheater. When ordering
parts,followthe instructions listedunderReplacementParts onpage17
ofthismanual.

20
ILLUSTRATED
PARTSBREAKDOWN
GFN2815R
GFP2816R
GFN2817R
GFP2818R
GFN2819R
GFP2820R