Kozy-World NF268 User manual

IMPORTANT SAFETY INSTRUCTIONS
Compact Electric Fireplace Heater
Item Code: NF268
GENERAL
1. Failure to follow these important safety instructions may cause fire, electric shock or damage. Read all
instructions before using this appliance. Following proper safety and operating instructions is the
responsibility of the owner.
2. This appliance is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep
combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 10 feet
from the front of this appliance.
3. CAUTION: Extreme caution is necessary when any heater is used by or near children or invalids.
Do not leave the heater operating and unattended.
4. Always unplug heater when not in use.
5. Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been
dropped or damaged in any manner.
6. Any repairs to this appliance should be carried out by a qualified service person.
7. Under no circumstances should this electric fireplace be modified. Parts having to be removed for
servicing must be replaced by a certified repair center prior to operating this electric fireplace again.
8. Do not use outdoors or anywhere that it can get wet.
9. This heater is not intended for use in bathrooms, laundry areas or similar indoor locations. Never
use this appliance near a bathtub or in the vicinity of water.
10. Do not run cord under carpeting. Do not cover cord with throw rugs, runners or the like. Arrange
cord away from traffic areas and where it will not be tripped over.
11. To disconnect this appliance, turn controls to the off position and remove plug from outlet.
12. Connect to properly grounded outlets only.
13. When this appliance is installed, it must be electrically grounded in accordance with local codes with
the current CSA C22.1 Canadian local codes for USA installations. Follow local codes and National
Electrical Code, ANSI/NFPA NO.70 and Canadian Code, CZ 22.2 No. 0.
14. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may
cause electric shock, fire or damage to the appliance.
15. To prevent fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces,
such as a bed, where openings may become blocked
16. CAUTION: This appliance gets hot and it contains internal parts that could arc or spark. Do not
use it in areas where gasoline, paint, or flammable liquids are used or stored. This electric fireplace
should not be used as a drying rack for clothing. Also, do not have Christmas stockings or
decorations hung on or near it.

17. Use this appliance only as described in this manual. All other uses not recommended by the
manufacturer may cause fire, electric shock or injury.
18. Avoid the use of an extension cord because it may overheat and cause a fire hazard. However if
you must use an extension cord, the cord shall be 16 AWG, 1875 Watts. The extension cord must be
a three-wire cord with grounding type plug and cord connector.
19. DO NOT ALLOW CHILDREN TO OPERATE. KEEP CHILDREN AND PETS AWAY
20. SAVE THESE INSTRUCTIONS.
LOCATING YOUR ELECTRIC FIREPLACE Your new freestanding electric fireplace may be installed
virtually anywhere in your home. However, when choosing a location for your new electric fireplace,
ensure that the general safety instructions are followed. For best results, install the electric fireplace
out of direct sunlight.
2

LEG ASSEMBLY
Before using your unit, please install the legs as shown in diagram below.
WARNING: Electrical
outlet wiring must comply with
local building codes and all
other applicable
ELECTRICAL CONNECTION
regulations to reduce the risk
of fire, electrical shock and
injury.
A 15 AMP, 120 Volt, 60Hz circuit with a properly
grounded outlet is required. Preferably, the
heater will be on a dedicated circuit. Other
appliances on the same circuit may cause the
circuit breaker to trip or the fuse to blow when
the heater is in operation. The unit comes
standard with a 6' (1828mm) long three wire
cord exiting from the rear of the fireplace.
Plan the installation to avoid the use of an
extension cord. If an extension cord must be
used, it must be a mini- mum 16 AWG three
wire with grounding type plug connector and rated
no less than 1875 Watts.
WARNING: Do not use this
fireplace if any part of it has
been under water. Immediately
call a qualified service
technician to inspect the
fireplace and replace any part
of the electrical system if
necessary.
ELECTRICAL SPECIFICATIONS
Voltage................120 VAC/60Hz
Total Amps...........11.3 Amps
Total Watts...........1500 Watts
Heater Ratings.....1400 Watts (+5%,-10%)
3

Compact Electric Fireplace Heater
Item Code: NF268
OPERATING INSTRUCTIONS
Controls and switches are located on front panel inside the glass doors.
1500W 750W Flame
FLAME: Press this button into the 1 position
for main power and flame effect light. The
indicator light will turn on.
750W : For low heat function - Press this
switch while the FLAME switch is in the 1
position for low heat. The indicator light will
turn on.
1500W: For high heat function - Press this
switch while the FLAME and 750W
switches are in the 1 position for high heat.
The indicator light will turn on.
THERMOSTAT: To adjust the temperature to
your individual requirements. Turn the ther-
mostat dial to the right (clockwise) to increase
the desired temperature and to the left for
lower temperature. This thermostat control
dial can only be used while the FLAME
switch and 750W/1500W switches are in
the 1 position. When the heater reaches the
desired temperature, the heater and
750W/1500W indicator light will turn off
and the fan will stop working for air flow.
FLAME INTENSITY: Turn the dimmer dial
clockwise or counter-clockwise to get the
desired flame intensity. The dimmer switch
can only be used when the FLAME switch is
in the 1 position.
NOTE: When the FLAME switch is turned in
O position, all other heater functions will stop
even though the switches may be in the 1
position.
THERMOSTAT CONTROL: Set the thermo-
stat dial fully clockwise to the maximum
position initially. When the room is warm
enough, reduce the setting by slowly turning
the thermostat dial counter-clockwise until the
heater just clicks off. This will then maintain
the room temperature at the desired level.

SERVICE INSTRUCTIONS
WARNING: Disconnect power
before attempting any
maintenance or cleaning to
reduce the risk of fire, electri-
cal shock or personal injury.
REPLACING LIGHT BULBS
CAUTION: Even though the glass is safety glass it
may break if bumped, struck or dropped. Care
must be taken when handling the glass.
There is one (1) 40W Type B-10 bulb for the
flame generation.
1. Unplug the unit.
2. Open the door of the unit with the handle.
3. Loosen the two (2) screws at the front of the
logset inside the stove.
4. Carefully lift the
logset up far enough
to access the light
bulb. You will find one
40W Type B-10 bulb
under the logset bed.
5. Loosen and remove the burnt out bulb and
replace with new 40 watt Type B-10 bulb.
6. Return the logset bed and secure with the two
screws.
7. Plug in the unit.
WARNING: Do not exceed
40 Watts for light bulb.
Use of a higher rated bulb
may result in a fire
causing property damage
and personal injury.
MADE IN CHINA
MAINTENANCE OF MOTORS
The motors used on both blower fan and
flame simulator assembly are prelubricated
for the extended life of the motor, no further
lubrication is required. However,
periodic cleaning/vacuuming of the fan/heater
unit is recommended.
WARNING: Make sure
that the power is turned
off before proceeding.
GLASS INFORMATION
1. Under no circumstances should this
product be operated with missing or broken
glass.
2. Do not strike or slam the glass.
3. Do not use abrasive cleaners to clean the
glass.
4. Replacement glass is available from the
manufacturer and replacement should be
carried out by a qualified service person.
CLEANING
WARNING: Wait until the
unit has completely
cooled before attempting
any cleaning.
To clean the unit, first turn off controls on unit
and unplug unit from power source.
To clean the glass door: remove dust with
clean dry cloth or to remove finger prints and
other marks clean glass with clean damp
cloth. Do not use abrasive cleaners or spray
liquids on glass door surfaces.
Metal and metal painted parts should be
cleaned with clean damp cloth only. Do not
use abrasive cleaners or spray liquids on this
surface.