Kozyard Alicia User manual

Assembly Manual
Alicia swing chair
Kozyard LLC Products
© Copyright 2016 - 2023 Kozyard LLC. | All Rights Reserved. Version: 09182023

BEFORE ASSEMBLING,MAKE SURE THAT YOU LAY OUT AND IDENTIFY ALL PARTS LISTED
BELOW IN THE PARTS LIST. INSTALL ON LEVEL GROUND.
INSTALL NOT LESS THAN 6 FEET FROM ANY OBSTRUCTION SUCH AS FENCE, GARAGE, HOUSE,
OVERHANGING BRANCHES, LAUNDRY LINES,OR ELECTRICAL WIRES.
TIGHTEN ALL NUTS AND BOLTS SECURELY. ALL BOLTS SHOULD BE HAND TIGHENED
BEFORE USE. NEVER USE POWER TOOLS OR EXCESSIVE FORCE DURING ASSEMBLY AND
TIGHTENING OF BOLTS.
IT IS RECOMMENDED TO BE AT LEAST 2 PEOPLE FORE A SAFE ASSEMBLY OF THE PRODUCT.
ASEEMBLY INSTUCTION
TOOL REQUIRED:
ALLEN WRENCH SMALL WRENCH
2 PERSON
ASSEMBLY
(PROVIDED)
IMPORTANT NOTICE:
1. Please refrain from kneeling or standing on the swing chair.
2. Ensure that the weight on the swing does not exceed the 525 lbs limit.
3. Prior to use, make certain that the swing is positioned on a stable, level surface.
4. When encountering rain or snow, remember to store the cushion away.

LEG CROSS HANGING PIPE BACK LEG CROSS BACK LEG CROSS
E1X4
EX2 FX1 GX1
LEG TUBE LEG TUBE TOP CROSS BAR TOP CROSS BAR
BX2
AX2 CX1 DX1
TX4
SX2 UX4 VX21
PX2
OX1 QX2 RX2
CANOPY TUBE CANOPY TUBE CANOPY BOLT
BOLTBOLTBOLTBOLT
BOLTBOLTBOLT
LX2
KX2 MX1 NX4
SPRING HOOK ARMREST SEAT & BACK
FRAME
CUSHION
IX2
HX2 JX1 J1X1
NUT
Part list

ALLEN KEY
WRENCH
WASHER PLASTIC SCREW PLASTIC END
CAP
WX21 YX2 ZX21
Part list

STEP -1 Connect part D and part C to build the beam using bolt Q
washer W, nut V and plastic end-cap Z as shown in diagram.
STEP -2 Connect part A and part B with the beam using bolt U
washer W, nut V and plastic end-cap Z as shown in diagram.
Attention: Both Part A should be on the same side, and both Part B
should be on the other side.
C
D
Q
W V Z
A
A
B
B
WV Z
U

STEP -3 Connect part E and legs (part A&B) using bolt N
washer W,nut V and plastic end-cap Z as shown in
diagram.
STEP -4 Connect part G and part F to build a connection
tube for the rear foot using bolt O,washer X,nut W
and plastic end-cap Z as shown in diagram.
E
E
W V Z
N
F
G
O
WV Z

STEP -5 Connect the rear foot tube with part B using bolt T
washer W,nut V and plastic end-cap Z as shown in
diagram.
STEP -6
Connect part I and part J using bolt R washer W,nut V and
plasticend-cap Z as shown in diagram.
I
I
J
R
V
ZW
F
G
T
W V Z

STEP -7
STEP -8 Use part H to hook the seat to the frame.
1. Connect part E with backseat (part J1) using
bolt S, washer X, nut W and plastic end-cap Z
as shown in diagram.
2. Connect part E to armrest (part I)
using bolt P, washer W, nut V and plastic
end-cap Z as shown in
diagram.
E1
Z V W
ZV W
P
S
H

STEP -9 Affix part K to beam using screw Y.
STEP -10 Insert part L to canopy.
K
KY
L

STEP -11 Connect Part L and Part K to support canopy.
STEP -12 Place cushion part J1 onto the frame. If it rains or snows,
please remember to store cushion part J1 away.
In the end, check that all screws are securely tightened before use.
J1

866-355-0018