Kozyard KZSW3135 User manual

Assembly Manual
Duluxe 3 Person Swing Chair
Kozyard LLC Products
www.kozyard.com
©
Copyright 2016 - 2023 Kozyard LLC. | All Rights Reserved.
Version:20231006

• Prior to assembly, ensure that you lay out and identify all the parts listed in
the parts list.
• Tighten all nuts and bolts securely. Hand-tighten all bolts before use. Avoid
using power tools or applying excessive force during assembly and bolt tight-
ening.
• Install at a minimum distance of 6 feet from any obstructions, such as fences,
garages, houses, overhanging branches, laundry lines, or electrical wires.
• It is recommended to be at least 2 people for a safe assembly of the
product.
• If you encounter any difficulties during assembly or if any part is missing or
damaged, please don't hesitate to contact our customer service team via
email at [e-mail] or by calling our toll-free number at
866-355-0018.
Assembly Instructions
Care and warranty
• The weight capacity of this swing chair is 700 lbs.
• Clean the frame components and fabric with a mild soap solution, then rinse
thoroughly. Avoid using bleach, acid, or any other solvents on either the fabric or
frame components.
• For a comprehensive warranty policy, please visit www.kozyard.com. Be aware
that warranty terms can change without prior notification.
• For the best performance and safety of your chair, inspect and tighten all bolts
and fasteners regularly
Warning:
1. Do not kneel or stand on swing chair.
2. Do not exceed 700lbs weight limit.
3. Make sure swing is located on a solid level surface.
4. Put away the cushion when it’s rain or snow.

LEG TUBE
HANGING PIPE
SPRING HOOK
BOLT(M8*100)
BOLT(M8*80) BOLT(M8*65)
NUT ROOF SCREW
BOLT(M8*62) CUSHION
BOLT(M6*89) BOLT(M6*20) BOLT(M8*55)
ARMREST CANOPY ARMREST
BACK LEG CROSS SEAT FRAME BACK FRAME
LEG TUBE TOP BEAM CROSS BAR
AX2
EX4
IX2
MX4
M6X4 M8X14
QX2 RX4 SX2 TX3
YX2
NX4 OX8 PX2
JX1 J1X1 KX1
FX1 GX1 HX1
BX2 CX1 DX2
W
WASHER
M6X12 M8X14
X
SCREW CAP
M6X4 M8X14
Z
Part list

Attention: Both part A should be the same side,and both part B should
be in the other side.
Step 1:
Begin by connecting the leg tube (Part A) and (Part B) with the top beam (Part C)
using bolt M, washer X, and nut W, as illustrated in the diagram. Next, connect the
back leg cross (Part F) with the leg tube (Part B) using bolt N, washer X, and nut W,
following the diagram.
Step 2:
Attach the leg tube (Part A) and (Part B) to the cross bar (Part D) using bolt O and
washer X, following the diagram.

Step 3:
Start by connecting the armrest (Part J) and (Part J1) with the back frame (Part H)
using bolt S, washer X, and nut W, following the diagram. Then, attach the armrest
(Part J) and (Part J1) to the seat frame (Part G) using bolt R, washer X, and nut W, as
indicated in the diagram.
Step 4:
Begin by connecting the hanging tube (Part E) with the armrest (Part J/J1) and back
frame (Part H) using bolt Q, washer X, and nut W, as depicted in the diagram. Then,
connect Part E with the armrest (Part J/J1) using bolt P, washer X, and nut W, follow-
ing the diagram. Finally, insert the spring hook (Part I) into the hanging tube (Part E),

Attach the canopy (Part K) to the top beam (Part C).
Step 5:
Step 6:
Using spring hook (part H) to hook the seat to the frame as shown
in diagram.as shown in the diagram.

Connect canopy with top beam using bolt Y.
Place cushion (Part T) on the seat frame as shown in dragram.
Make sure all of screws are fixed tightly then cover all screw caps Z
(M6 or M8) before use in level solid ground.
Y
Step 7:
Step 8:
Step 9:

Put on cover for swing chair in order to preserve the chair.
Cover
Step 10:

866-355-0018
Kozyard LLC
© Copyright 2016 - 2023 Kozyard LLC. | All Rights Reserved.