Kramer TP-600TRxr User manual

P/N: 2900-301503 Rev 1 www.kramerAV.com
USER MANUAL
MODELS:
TP-600TRxr
TP-600TR
4K60 HDMI/USB Extender

Kramer Electronics Ltd.
TP-600TRxr –Contents
i
Contents
Introduction 1
Getting Started 1
Overview 2
Typical Applications 3
Defining TP-600TRxr 4K60 HDMI/USB Extender 4
Mounting TP-600TRxr 6
Connecting the 4K60 HDMI/USB Extender 7
Connecting TP-600TRxr 7
Connecting TP-600TR 9
Connecting to TP-600TRxr via RS-232 11
Setting the DIP-Switches 11
Technical Specifications 12
TP-600TRxr Specifications 12
TP-600TR Specifications 13

Kramer Electronics Ltd.
TP-600TRxr –Introduction
1
Introduction
Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world
of unique, creative, and affordable solutions to the vast range of problems that confront the
video, audio, presentation, and broadcasting professional on a daily basis. In recent years, we
have redesigned and upgraded most of our line, making the best even better!
Getting Started
We recommend that you:
•Unpack the equipment carefully and save the original box and packaging materials for
possible future shipment.
•Review the contents of this user manual.
Go to www.kramerav.com/downloads/TP-600TRxr or www.kramerav.com/downloads/TP-
600TRto check for up-to-date user manuals, application programs, and to check if firmware
upgrades are available (where appropriate).
Achieving Best Performance
•Use only good quality connection cables (we recommend Kramer high-performance,
high-resolution cables) to avoid interference, deterioration in signal quality due to poor
matching, and elevated noise levels (often associated with low quality cables).
•Do not secure the cables in tight bundles or roll the slack into tight coils.
•Avoid interference from neighboring electrical appliances that may adversely influence
signal quality.
•Position your Kramer TP-600TRxr / TP-600TR away from moisture, excessive sunlight
and dust.
Safety Instructions
Caution:
•This equipment is to be used only inside a building. It may only be connected to other
equipment that is installed inside a building.
•For products with relay terminals and GPI\O ports, please refer to the permitted rating
for an external connection, located next to the terminal or in the User Manual.
•There are no operator serviceable parts inside the unit.
Warning:
•Use only the power cord that is supplied with the unit.
•To ensure continuous risk protection, replace fuses only according to the rating
specified on the product label which is located on the bottom of the unit.

Kramer Electronics Ltd.
TP-600TRxr –Introduction
2
Recycling Kramer Products
The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC aims to reduce
the amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected
and recycled. To comply with the WEEE Directive, Kramer Electronics has made
arrangements with the European Advanced Recycling Network (EARN) and will cover any
costs of treatment, recycling and recovery of waste Kramer Electronics branded equipment on
arrival at the EARN facility. For details of Kramer’s recycling arrangements in your particular
country go to our recycling pages at www.kramerav.com/il/quality/environment.
Overview
Congratulations on purchasing your Kramer TP-600TRxr/TP-600TR 4K60 HDMI/USB
Extender.
TP-600TR is identical to TP-600TRxr except for ETH extension. TP-600TRxr, in this User
Manual, refers to both devices, unless specified otherwise.
TP-600TRxr is a high-performance, long-reach HDBaseT 3.0 extender for 4K60Hz (4:4:4)
HDMI, USB, Ethernet (TP-600TRxr only), RS-232, and IR signals over twisted pair, flexibly
set as transmitter-side or receiver-side device. TP-600TRxr transmitter-side converts all input
signals into the transmitted HDBaseT 3.0 signal. TP-600TRxr receiver-side receives the
HDBaseT 3.0 signal and converts it back into the original input signals.
TP-600TRxr extends video signals up to 100m (330ft) over CAT copper cables at 4K@60Hz
(4:4:4) video resolution.
TP-600TR extends video signals up to 40m (130ft) over CAT copper cables at 4K@60Hz
(4:4:4) video resolution and up to 70m (230ft) at 4K@30Hz (4:4:4).
TP-600TRxr provides exceptional quality, advanced and user-friendly operation, and flexible
control.
Exceptional Quality
•High Performance Standard Extender –Professional HDBaseT extender for providing
extended-reach signals over twisted-pair copper infrastructures. TP-600TRxr is a
standard extender that can be connected to any market-available HDBaseT-compliant
extension product. For optimum extension reach and performance, use recommended
Kramer cables.
•HDMI Signal Extension –HDCP 2.3, EDID and CEC signals are passed through from
the source to the display. Supports HDR10, deep color, x.v.Color™, lip sync, HDMI
uncompressed audio channels, Dolby TrueHD, DTS-HD, 2K, 4K, and 3D as specified in
HDMI 2.0.
•HDMI extension –Uncompressed 4K@60Hz (4:4:4).
•I-EDIDPro™ Kramer Intelligent EDID Processing™ –Intelligent EDID handling,
processing, and pass-through algorithm that ensures Plug and Play operation for HDMI
source and display systems.

Kramer Electronics Ltd.
TP-600TRxr –Introduction
3
Advanced and User-friendly Operation
•HDMI Mirroring –Transmitter-side extender mirrors input HDMI signal to loop output port
for connecting a local monitor or an additional unit in a daisy chain.
•Flexible USB 2.0 Extension –An active USB host is connected to the extender at either
the transmitter or receiver sides. USB 2.0 signals are extended between the extender
transmitter and receiver sides, enabling connection of the active USB host to both local
and remote USB devices, such as camera and audio devices, or HID (Human Interface
Devices) mouse or keyboard devices.
•Cost-effective Maintenance –Status LED indicators for HDMI, Loop, HDBT, and USB
active host ports, facilitate easy local maintenance and troubleshooting.
•Easy and Elegant Installation –MegaTOOLS™ fan-less enclosure for dropped-ceiling
mounting, or side-by-side mounting of 2 units in a 1U rack space with the recommended
rack adapter.
Flexible Connectivity
•Multi-channel Audio Transmission –Up to 32 channels of digital stereo uncompressed
signals for supporting studio-grade surround sound.
•Flexible USB 2.0 host and devices extension.
•Ethernet Extension (TP-600TRxr only) –Ethernet interface data flows in both directions,
allowing extension of up to 1 Gbps Ethernet connectivity for LAN communication and
device control.
•Bidirectional RS-232 Extension –Serial interface data flows in both directions, allowing
data transmission and device control.
•Bidirectional Infrared Extension –IR interface data flows in both directions, allowing
remote control of peripheral devices located at either end of the extended line.
Typical Applications
TP-600TRxr is ideal for the following typical applications:
•Corporate –Hybrid and online meetings.
•Education –Hybrid and online learning and training.
•Any AV, Ethernet (TP-600TRxr only) and USB room extension applications such as
conference rooms, boardrooms, and training facilities.

Kramer Electronics Ltd.
TP-600TRxr –Defining TP-600TRxr 4K60 HDMI/USB Extender
4
Defining TP-600TRxr 4K60
HDMI/USB Extender
This section defines TP-600TRxr and TP-600TR.
The extender device functions as a transmitter or receiver as defined by the SETUP
DIP-switch 1 setting on the rear panel (see Setting the DIP-Switches on page 11).
Figure 1: TP-600TRxr 4K60 HDMI/USB Extender Front Panel
Figure 2: TP-600TR 4K60 HDMI/USB Extender Front Panel
#
Feature
Function
HOST USB B 2.0
Connector
Connect to the USB host (for example, a laptop) to communicate with the USB
peripheral devices (for example, a smart board) connected to USB device ports
on either the transmitter or the receiver sides of the extender (see Connecting
the 4K60 HDMI/USB Extender on page 7).
ACTIVE HOST
LED
Lights orange when the USB host side is active
ACTIVE Rx LED
Lights green when the extender receiver function is active
IN LED
Lights blue when an active HDMI input signal is detected on HDMI IN.
OUT LED
Lights blue when an output acceptor device is connected.
TX LOOP
Transmitter mode
Lights blue an active signal is transmitted on the Tx LOOP
port.
Receiver mode
N/A
LINK LED
Lights green when the HDBT active link connection is established.
ON LED
Lights green when the device receives power.
1
2
3
4
5
6
7
8

Kramer Electronics Ltd.
TP-600TRxr –Defining TP-600TRxr 4K60 HDMI/USB Extender
5
Figure 3: TP-600TRxr 4K60 HDMI/USB Extender Rear Panel
Figure 4: TP-600TR 4K60 HDMI/USB Extender Rear Panel
#
Feature
Function
ENTER Button
Press to move to the next level in the OSD screen or to accept a new
parameter.
HDMI TX IN
Connector
Transmitter mode
Connect to an HDMI source.
Receiver Mode
N/A
HDMI Rx
OUT/Tx LOOP
Connector
Transmitter mode
Connect to a local acceptor.
Receiver mode
Connect to an HDMI acceptor.
USB A 2.0 Fast-
Charging
Connectors (3)
Connect to the USB local peripheral devices (for example, a USB camera, a
soundbar, microphone and so on).
IR 3.5mm Mini
Jack Connector
Connect to an external IR emitter to control a local IR-controlled device from the
remote extender (for example, TP-600TRxr).
Connect to an IR sensor to control a remote IR-controlled device connected to
the remote extender side (for example, TP-600TRxr).
RS-232 3-pin
Terminal Block
Connect to a controller device (for example, SL240C) to control a remote device
via serial connection (for example, the remotely connected PTZ USB camera).
ETHERNET
RJ-45 Connector
Connect to LAN.
SETUP 4-way
DIP-switch
Sets the device behavior (see Setting the DIP-Switches on page 11).
12V DC Power
Connector
Connect to the power supply.
9
10
11
12
13
14
15
16
17

Kramer Electronics Ltd.
TP-600TRxr –Mounting TP-600TRxr
6
Mounting TP-600TRxr
This section provides instructions for mounting TP-600TRxr. Before installing, verify that the
environment is within the recommended range:
•Operation temperature –0to 40C (32 to 104F).
•Storage temperature –-40to +70C (-40 to +158F).
•Humidity –10% to 90%, RHL non-condensing.
Caution:
•Mount TP-600TRxr before connecting any cables or power.
Warning:
•Ensure that the environment (e.g., maximum ambient temperature & air flow) is
compatible for the device.
•Avoid uneven mechanical loading.
•Appropriate consideration of equipment nameplate ratings should be used for avoiding
overloading of the circuits.
•Reliable earthing of rack-mounted equipment should be maintained.
•Maximum mounting height for the device is 2 meters.
Mount TP-600TRxr in a rack:
•Use the recommended rack adapter
(see www.kramerav.com/product/TP-600TRxr).
Mount TP-600TRxr on a surface using one of the following
methods:
•Attach the rubber feet and place the unit on a flat surface.
•Fasten a bracket (included) on each side of the unit and attach it to
a flat surface. For more information go to
www.kramerav.com/downloads/TP-600TRxr.

Kramer Electronics Ltd.
TP-600TRxr –Connecting the 4K60 HDMI/USB Extender
7
Connecting the 4K60 HDMI/USB
Extender
You can use two TP-600TRxr units, define them as transmitter and receiver and then connect
the transmitter to the receiver (as described in this section). You can also connect the device
to a different unit. For example:
•Connecting TP-600TRxr that is set as a transmitter to the Kramer TP-590R receiver.
•Connecting a transmitter (for example, the Kramer TP-590T transmitter) to a
TP-600TRxr that is set as a receiver.
•Connecting the TP-600TRxr (defined as a transmitter or receiver to a switcher or other
system, for example, the VS-84UT).
This section describes the following actions:
•Connecting TP-600TRxr on page 7.
•Connecting TP-600TR on page 9.
•Connecting to TP-600TRxr via RS-232 on page 11.
•Error! Reference source not found. on page Error! Bookmark not defined..
•Setting the DIP-Switches on page 11.
Always switch off the power to each device before connecting it to your TP-600TRxr. After
connecting your TP-600TRxr, connect its power and then switch on the power to each
device.
Connecting TP-600TRxr
Figure 5: Connecting to TP-600TRxr

Kramer Electronics Ltd.
TP-600TRxr –Connecting the 4K60 HDMI/USB Extender
8
To connect TP-600TRxr as illustrated in the example in Figure 5:
1. Use the DIP-switches to define one device as a transmitter and the other as a
receiver (see Setting the DIP-Switches on page 11).
2. Connect the HDBT port on the TP-600TRxr transmitter side to the HDBT port on
the TP-600TRxr receiver side.
3. On the TP-600TRxr transmitter side, connect an HDMI source (for example, a laptop) to
the HDMI Tx IN connector .
4. On the TP-600TRxr transmitter side, connect the HDMI Rx OUT/Tx LOOP connector
to an HDMI acceptor.
5. On the TP-600TRxr receiver side, connect the HDMI Rx OUT/Tx LOOP connector to
an HDMI acceptor (for example, a smart TV).
6. Connect the USB ports:
▪Connect the HOST USB port to a laptop or room PC.
The HOST USB port can be connected to either the transmitter or the receiver
side, as necessary.
▪Connect the USB DEVICE ports on the transmitter side to USB devices (for example,
the room microphone, mouse, and keyboard).
▪Connect the USB DEVICE ports on the receiver side to USB devices (for example, a
smart board, soundbar and camera).
USB devices can be connected to both the transmitter and receiver sides, as
necessary.
7. To control the smart TV via IR, connect the following:
▪On the TP-600TRxr transmitter side, connect an IR sensor cable to the IR 3.5mm
mini jack .
▪On the TP-600TRxr receiver side, connect the IR 3.5mm mini jack to an emitter
cable and attach the emitter side to the IR sensor of the smart TV.
Point the smart TV IR remote controller to the IR sensor to pass an IR command via
HDBT to the smart TV.
8. To Control the smart TV via Ethernet, connect the following:
▪On the TP-600TRxr transmitter side, connect a room controller (for example, the
Kramer SL-240C with Kramer Control) to the Ethernet RJ-45 port .
▪On the TP-600TRxr receiver side, connect the Ethernet RJ-45 port to the smart
TV.
Send IP commands via the room controller to the smart TV via LAN.
9. To control the PTZ camera, connect the following:
▪On TP-600TRxr transmitter side connect a controller (for example, SL-240C room
controller) to the RS-232 port (and also to the ETHERNET RJ-45 port ).
▪On TP-600TRxr receiver side connect the RS-232 port to a PTZ camera.
14
9
9
10
11
11
13
13
15
15
14
15
14