Kramer VP-8x8TP User manual

Kramer Electronics, Ltd.
USER MANUAL
Model:
VP-8x8TP
8x8 UXGA/Audio Matrix Switcher

Contents
i
Contents
1Introduction 1
2Getting Started 1
2.1 Quick Start 1
3Overview 3
3.1 Terminology Used in this User Manual 4
3.2 Shielded Twisted Pair and Unshielded Twisted Pair 4
3.3 Defining the EDID 5
4Defining theVP-8x8TP 8x8 UXGA/Audio Matrix Switcher 6
5Installing the VP-8x8TP in a Rack 9
6Connecting and Configuring the VP-8x8TP 8x8 UXGA/Audio Matrix Switcher 10
6.1 Connecting the VP-8x8TP 8x8 UXGA/Audio Matrix Switcher 10
6.2 Connecting to the VP-8x8TP 8x8 UXGA/Audio Matrix Switcher via RS-485 11
6.2.1 Setting the RS-485 Bus Termination 12
6.2.2 Setting the RS-485 Bus Machine Number 12
6.3 Connecting to VP-8x8TP via the RS-232 Port 12
6.4 Configuring the Ethernet Port 12
6.4.1 Connecting via the Ethernet Port 12
6.4.2 Ethernet Port Configuration 14
6.5 Operating the VP-8x8TP8x8 UXGA/Audio Matrix SwitcherRemotely 16
6.6 Setting the Switching Delay Time 16
7Operating theVP-8x8TP 8x8 UXGA/Audio Matrix Switcher 17
7.1 Switching Inputs and Outputs 17
7.1.1 Switching an Input to an Output 17
7.1.2 Switching an Input to all Outputs 17
7.1.3 Disconnecting an Input from an Output 17
7.1.4 Disconnecting all Inputs from Outputs 18
7.2 The 7-Segment Status Display Modes 18
7.2.1 Status Display Immediately After Power is Turned On 18
7.2.2 Status Display During Normal Operation 18
7.2.3 Status Display During Audio Level Setting 19
7.3 Confirming Settings 19
7.3.1 Toggling between the At Once and Confirm Modes 19
7.3.2 Confirming a Switching Action 20
7.4 Storing/Recalling Input-Output Configurations 20
7.4.1 Storing an Input-Output Configuration 20
7.4.2 Recalling an Input-Output Configuration 21
7.5 Locking the Front Panel 21
7.6 Choosing the Audio-Follow-Video or Breakaway Option 21
7.6.1 Setting the Audio-Follow-Video Option 22
7.6.2 Setting the Breakaway Option 22

KRAMER: SIMPLE CREATIVE TECHNOLOGY
Contents
ii
7.7 Setting the Audio Input Gain 22
7.8 Using the IR Transmitter 23
8Operating MultipleVP-8x8TP Units Remotely via RS-232 23
9Operating theVP-8x8TP Remotely via your Web Browser 24
9.1 Connecting to the VP-8x8TP8x8 UXGA/Audio Matrix Switcher via your Browser 25
9.2 The Main Switching Matrix Page 26
9.2.1 Switching an Input to an Output 27
9.2.2 Setting the AFV Mode 27
9.2.3 Operating in the Offline Mode 28
9.2.4 Storing and Recalling Setups 29
9.2.5 Locking the Front Panel Buttons 31
9.3 Audio Input Gain Control Page 31
9.4 The Configuration Page 32
10 EDID 33
11 Firmware Upgrade 33
12 Technical Specifications 34
13 Default Communication Parameters 34
14 Default EDID 35
15 Tables of Hex Codesfor Serial Communication(Protocol 2000) 37
16 Kramer Protocol 38
16.1 Switching Protocols 38
16.1.1 Switching Protocols via the Front Panel Buttons 38
16.1.2 Switching Protocols via Protocol Commands 39
16.2 Kramer Protocol 3000 39
16.2.1 Protocol 3000 Syntax 39
16.2.2 Command Parts Details 40
16.3 Kramer Protocol 2000 46
Figures
Figure 1: VP-8x8TP 8x8 UXGA/Audio Matrix Switcher Front Panel 6
Figure 2: VP-8x8TP 8x8 UXGA/Audio Matrix Switcher Rear Panel 6
Figure 3: Connecting the VP-8x8TP 8x8 UXGA/Audio Matrix Switcher 10
Figure 4: The RS-485 TERM Dipswitch 12
Figure 5: Local Area Connection Properties Window 13
Figure 6: Internet Protocol (TCP/IP) Properties Window 14
Figure 7: Connect Window 15
Figure 8: Device Properties Window 16
Figure 9: Status Display Five Seconds After Turn On 18
Figure 10: Status Display During Normal Operation 18
Figure 11: Status Display Showing INPUT 3, Gain -4.5 19
Figure 12: Storing and Recalling using the Input-Output Buttons 20
Figure 13: Status Display Showing Audio Gain for Input 3, Gain -4.5 22

Contents
iii
Figure 14: Control Configuration via RS-232 and RS-485 24
Figure 15: Java Test Page Success Message 24
Figure 16: Entering the IP Number in the Address Bar 25
Figure 17: The Loading Page 25
Figure 18: First Time Security Warning 26
Figure 19: Main Switching Matrix Page 26
Figure 20: Selecting a Switching Point on the Matrix 27
Figure 21: Switching an Input to an Output 27
Figure 22: AFV Mode Warning 28
Figure 23: AFV Mode Audio Channels Switched 28
Figure 24: Switching Audio in the Offline Mode 29
Figure 25: Exiting Offline Warning 29
Figure 26: Selecting Preset 07 30
Figure 27: Selecting Preset 03 30
Figure 28: Recalling a Preset in Offline Mode 31
Figure 29: Audio Gain Control Page 31
Figure 30: Selecting Audio Input Gain for Channel 2 32
Figure 31: Configuration Page 32
Tables
Table 1: Terminology Used in this Manual 4
Table 2: VP-8x8TP Front and Rear Panel Features 7
Table 3: Technical Specifications of the VP-8x8TP 8x8 UXGA/Audio Matrix Switcher 34
Table 4: Default Communication Parameters 34
Table 5: VP-8x8TP Video Signal Codes 36
Table 6: VP-8x8TP Audio Signal Codes 36
Table 7: VP-8x8TP Audio Input Gain Codes 37
Table 8: VP-8x8TP Hex Codes for Switching Video Channels 37
Table 9: VP-8x8TP Hex Codes for Switching Audio Channels 37
Table 10: VP-8x8TP Hex Codes for Increasing/Decreasing the Audio Input Gain 38
Table 11: VP-8x8TP Hex Codes for Setting the Audio Input Gain 38
Table 12: Instruction Codes for Protocol 3000 40
Table 13: Protocol Definitions 46
Table 14: Instruction Codes for Protocol 2000 47

Introduction
1
1 Introduction
Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been
providing a world of unique, creative, and affordable solutions to the vast range of
problems that confront the video, audio, presentation, and broadcasting
professional on a daily basis. In recent years, we have redesigned and upgraded
most of our line, making the best even better! Our 1,000-plus different models now
appear in 11 groups1
Congratulations on purchasing your VP-8x8TP 8x8 UXGA/Audio Matrix Switcher,
which is ideal for the following typical applications:
that are clearly defined by function.
•Professional display systems requiring a true 8x8 computer graphics and
audio matrix operation
•Long range multimedia and presentation source and acceptor selection
The package includes the following items:
•VP-8x8TP 8x8 UXGA/Audio Matrix Switcher
•K-Router Windows®-based Kramer control software2
•Kramer RC-IR3Infrared Remote Control Transmitter (including the required
battery and a separate user manual
4)
•Power cord3and this user manual4
2 Getting Started
We recommend that you:
•Unpack the equipment carefully and save the original box and packaging
materials for possible future shipment
•Review the contents of this user manual
•Use Kramer high performance high-resolution cables5
2.1 Quick Start
This quick start chart summarizes the basic setup and operation steps.
1 GROUP 1: Distribution Amplifiers; GROUP 2: Switchers and Matrix Switchers; GROUP 3: Control Systems; GROUP 4:
Format/Standards Converters; GROUP 5: Range Extenders and Repeaters; GROUP 6: Specialty AV Products; GROUP 7: Scan
Converters and Scalers; GROUP 8: Cables and Connectors; GROUP 9: Room Connectivity; GROUP 10: Accessories and Rack
Adapters; GROUP 11: Sierra Products
2 Downloadable from our Web site at http://www kramerelectronics com
3 We recommend that you use only the power cord that is supplied with this machine
4 Download up-to-date Kramer user manuals from http://www kramerelectronics com
5 The complete list of Kramer cables is available at http://www kramerelectronics com

KRAMER: SIMPLE CREATIVE TECHNOLOGY
Getting Started
2

Overview
3
3 Overview
The VP-8x8TP is a high performance 8x8 computer graphics video and audio
matrix switcher for high resolution video and stereo audio signals. The VP-8x8TP
is HDTV compatible and lets you route any combination of inputs and outputs over
TP (Twisted Pair) cable to compatible TP receivers.
In particular, the VP-8x8TP 8x8 UXGA/Audio Matrix Switcher features:
•Kramer’s innovative integrated sync processing Kr-isp®technology that lets
you achieve a sharp, stable image when the sync level is too low, by restoring
the sync signal waveform
•Resolution up to UXGA (1600 x 1200), 1080p
•Support for component video with suitable breakout cables1
•16 preset memory locations for quick access to common video and audio
configurations and audio gain status for each output
•Automatic detection of the connected input signals (the respective button
lights)
•A delayed switching mode (ranging from 0 to 3.5sec2
•DC-coupled video inputs and outputs
) for clean transitions
(seamless switching) when switching between non-genlocked sources
•Audio-follow-video and breakaway options
•Eight stereo unbalanced audio input signals on 3.5mm mini jacks
•Eight RJ-45 STP/UTP output connectors
•Over 100m (330ft) transmission range between the switcher and the TP
receiver
•Audio level control buttons for adjusting the signal level of each input
•Measurement and indication of the audio level for each input and output, in
relative dB
•A TAKE button, which allows you to place multiple switches in a queue and
then activate them simultaneously with one touch of this button
•A LOCK button to prevent tampering with the front panel
The VP-8x8TP can be controlled using the front panel buttons, or remotely via:
•RS-485 or RS-232 serial commands (using Kramer 2000 and 3000 Protocols)
transmitted by a touch screen system, PC, or other serial controller
•The Kramer infrared remote control transmitter or infrared remote extension
cable transmitter (optional)
•A Web browser over Ethernet
The VP-8x8TP is dependable, rugged, and fits into one vertical space (1U) of a
standard 19” professional rack.
1 For example, C-GM/5BM The complete list of Kramer cables is available at http://www kramerelectronics com
2 In increments of 0 5sec

KRAMER: SIMPLE CREATIVE TECHNOLOGY
Overview
4
To achieve the best performance:
•Use only good quality connection cables1
•Avoid interference from neighboring electrical appliances that may adversely
influence signal quality and position your Kramer VP-8x8TP away from
moisture, excessive sunlight and dust
to avoid interference, deterioration
in signal quality due to poor matching, and elevated noise levels (often
associated with low quality cables)
3.1 Terminology Used in this User Manual
Table 1 defines some terms that are used in this user manual.
Table 1: Terminology Used in this Manual
Term
Definition
802.3 The standard specification for Ethernet that is maintained by the Institute of Electrical
and Electronics Engineers (IEEE).
Dynamic Host Configuration
Protocol (DHCP) Allows the network administrator to distribute IP addresses from a central point and automatically send a new IP address when an Ethernet point is plugged into a different
network location.
Gateway A network position serving as an entry to another network. On the Internet, a node or
stopping point can be either a gateway node or a host (end-point) node.
IP Address A 32-binary digit number that identifies each sender or receiver (within a network via a
particular server or workstation) of data (HTML pages or e-mails) that is sent in packets
across the Internet. Every device connected to an IP network must have a unique IP
address. This address is used to reference the specific unit.
Local Area Network (LAN) Computers sharing a common communications line or wireless link, which often share a
server within a defined geographic area.
Media Access Control (MAC)
Address
A computer's unique hardware number (or address) in a LAN or other network. On an
Ethernet LAN, the (MAC) address is identical to the Ethernet address.
Transmission Control
Protocol/Internet Protocol
(TCP/IP)
The basic communication language or protocol of the Internet that breaks the message
into appropriately sized packets for the network, and can be used as a communications
protocol in an intranet or an extranet.
3.2 18BShielded Twisted Pair and Unshielded Twisted Pair
We recommend that you use Shielded Twisted Pair (STP) cable. There are
different grades of STP cable available, and we advise you to use the best quality
STP cable that you can afford. Our non-skew-free cable, Kramer BC-STP is
intended for digital signals and for analog signals where skewing is not an issue.
For cases where skewing occurs, our UTP skew-free cable, Kramer BC-XTP, may
be used. Bear in mind, though, that we advise using STP cables where possible,
since the compliance to electromagnetic interference has been tested using STP
cables.
Although Unshielded Twisted Pair (UTP) cable might be preferred for long range
applications, UTP cable should be installed as far as possible from electric cables,
motors, and so on, as these devices tend to create electromagnetic interference.
However, since the use of UTP cable might not conform to electromagnetic
standards, Kramer does not commit to meeting the standard with UTP cable.
1 Available from Kramer Electronics on our Web site at http://www.kramerelectronics.com

Overview
5
3.3 Defining the EDID
The Extended Display Identification Data (EDID1
1 Defined by a standard published by the Video Electronics Standards Association (VESA)
) is a data-structure, provided by
a display, to describe its capabilities to a graphics card (that is connected to the
display’s source). The EDID enables the PC or laptop to “know” what kind of
monitor is connected to the output. The EDID includes the manufacturer’s name,
the product type, the timing data supported by the display, the display size,
luminance data and (for digital displays only) the pixel mapping data.

KRAMER: SIMPLE CREATIVE TECHNOLOGY
Defining the VP-8x8TP 8x8 UXGA/Audio Matrix Switcher
6
4 Defining the VP-8x8TP 8x8 UXGA/Audio Matrix Switcher
Figure 1 and Table 2 define the front panel of the VP-8x8TP 8x8 UXGA/Audio Matrix Switcher.
Figure 1: VP-8x8TP 8x8 UXGA/Audio Matrix Switcher Front Panel
Figure 2 and Table 2 define the rear panel of the VP-8x8TP 8x8 UXGA/Audio Matrix Switcher.
Figure 2: VP-8x8TP 8x8 UXGA/Audio Matrix Switcher Rear Panel