Kramer VS-62H User manual

KRAMER ELECTRONICS LTD.
USER MANUAL
MODEL:
VS-62H
6x2 HDMI Matrix Switcher
P/N: 2900-300170 Rev 1

VS-62H - Contents
i
Contents
1Introduction 1
2Getting Started 2
2.1 Achieving the Best Performance 2
2.2 Safety Instructions 3
2.3 Recycling Kramer Products 3
3Overview 4
3.1 Using the IR Transmitter 5
4Defining the VS-62H 6x2 HDMI Matrix Switcher 6
5Installing in a Rack 8
6Connecting the VS-62H 6x2 HDMI Matrix Switcher 9
6.1 Connecting a Serial Controller to the VS-62H via RS-232 10
6.2 Connecting to the VS-62H via Ethernet 10
6.3 Connecting the Remote Contact-closure Switches 13
7Principles of Operation 15
7.1 Automatic Signal Detection 15
7.2 Input Switching Modes 15
7.3 EDID Operation 16
7.4 Step-in Functionality 16
8Operating the VS-62H 6x2 HDMI Matrix Switcher 17
8.1 Switching an Input to an Output 17
8.2 Acquiring an EDID from an Output 17
8.3 Muting and Unmuting the Outputs 18
8.4 Locking and Unlocking the Front Panel Buttons 19
8.5 Generating a Test Pattern 19
9Configuring and Maintaining the VS-62H 21
9.1 Setting the DIP-switches 21
9.2 Resetting the VS-62H to Factory Default Settings 22
9.3 Upgrading the Firmware 22
10 Operating the VS-62H Remotely via the Web Pages 23
10.1 Browsing the VS-62H Web Pages 23
10.2 The Routing Page 25
10.3 The EDID Page 30
10.4 The Device Setting Page 32
10.5 The Firmware Upgrade Page 33
10.6 The About Us Page 34
11 Wiring the Twisted Pair RJ-45 Connectors 35
12 Technical Specifications 36
13 Default Communication Parameters 37
14 Default EDID 38
15 Protocol 3000 40
15.1 Kramer Protocol 3000 Syntax 40
15.2 Kramer Protocol 3000 Commands 43

ii
VS-62H - Introduction
Figures
Figure 1: VS-62H 6x2 HDMI Matrix Switcher Front Panel 6
Figure 2: VS-62H 6x2 HDMI Matrix Switcher Rear Panel 7
Figure 3: Connecting the VS-62H 6x2 HDMI Matrix Switcher 9
Figure 4: Local Area Connection Properties Window 11
Figure 5: Internet Protocol Version 4 Properties Window 12
Figure 6: Internet Protocol Properties Window 13
Figure 7: Remote Contact-closure Switch Connections 14
Figure 8: Available Test Patterns 20
Figure 9: The Loading Page 23
Figure 10: The General Info Page 24
Figure 11: The Lock Button 24
Figure 12: The Routing Page 25
Figure 13: The Output Buttons 26
Figure 14: The Input Buttons 27
Figure 15: The Remote Device Control Window 28
Figure 16: Test Pattern Tab 29
Figure 17: The EDID Page 30
Figure 18: The Device Setting Page 32
Figure 19: The Firmware Upgrade Page 33
Figure 20: The About Us Page 34
Figure 21: TP Pinout Wiring 35

VS-62H - Introduction
1
1 Introduction
Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been
providing a world of unique, creative, and affordable solutions to the vast range of
problems that confront video, audio, presentation, and broadcasting professionals
on a daily basis. In recent years, we have redesigned and upgraded most of our
line, making the best even better!
Our 1,000-plus different models now appear in 11 groups that are clearly defined
by function: GROUP 1: Distribution Amplifiers; GROUP 2: Switchers and Routers;
GROUP 3: Control Systems; GROUP 4: Format/Standards Converters; GROUP 5:
Range Extenders and Repeaters; GROUP 6: Specialty AV Products; GROUP 7:
Scan Converters and Scalers; GROUP 8: Cables and Connectors; GROUP 9:
Room Connectivity; GROUP 10: Accessories and Rack Adapters and GROUP 11:
Sierra Video Products.
Congratulations on purchasing your Kramer VS-62H 6x2 HDMI Matrix Switcher
which is ideal for the following typical applications:
Conference rooms
Education
Hospitality

2
VS-62H - Getting Started
2 Getting Started
We recommend that you:
Unpack the equipment carefully and save the original box and packaging
materials for possible future shipment
Review the contents of this user manual
Go to http://www.kramerelectronics.com/support/product_downloads.asp
to check for up-to-date user manuals, application programs, and to check if
firmware upgrades are available (where appropriate).
2.1 Achieving the Best Performance
To achieve the best performance:
Use only good quality connection cables (we recommend Kramer high-
performance, high-resolution cables) to avoid interference, deterioration in
signal quality due to poor matching, and elevated noise levels (often
associated with low quality cables)
Do not secure the cables in tight bundles or roll the slack into tight coils
Avoid interference from neighboring electrical appliances that may adversely
influence signal quality
Position your VS-62H away from moisture, excessive sunlight and dust
This equipment is to be used only inside a building. It may only be
connected to other equipment that is installed inside a building
i
!

VS-62H - Getting Started
3
2.2 Safety Instructions
Caution:
There are no operator serviceable parts inside the unit
Warning:
Use only the power cord that is supplied with the unit.
Do not open the unit. High voltages can cause
electrical shock! Servicing by qualified personnel only
Warning:
Disconnect the power and unplug the unit from the wall
before installing
2.3 Recycling Kramer Products
The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC
aims to reduce the amount of WEEE sent for disposal to landfill or incineration by
requiring it to be collected and recycled. To comply with the WEEE Directive,
Kramer Electronics has made arrangements with the European Advanced
Recycling Network (EARN) and will cover any costs of treatment, recycling and
recovery of waste Kramer Electronics branded equipment on arrival at the EARN
facility. For details of Kramer’s recycling arrangements in your particular country
go to our recycling pages at http://www.kramerelectronics.com/support/recycling/.
!

4
VS-62H - Overview
3 Overview
The VS-62H is a high quality, 6x2 matrix switcher for HDMI signals. It reclocks and
equalizes the signals and can route any input to either or both outputs
simultaneously.
In particular, the VS-62H features:
Up to 8.91Gbps data rate (2.97Gbps per graphics channel)
Suitable for resolutions up to UXGA and 4K x 2K
Support for HDCP (High Definition Digital Content Protection)
True video clock detection
Automatic switching modes (last connected and priority switching)
HDMI Support –3D, Deep Color, x.v.Color™, Lip Sync , ARC, HEAC pass-
through, Dolby® TrueHD, Dolby Digital Plus, DTS−HD®, and 7.1 multi-
channel audio
I-EDIDPro™ Kramer Intelligent EDID Processing™ – Intelligent EDID
handling & processing algorithm ensures Plug and Play operation for HDMI
systems
Programmable step-in functionality when used in conjunction with
compatible step-in devices, such as the SID-X3N (using an HDMI cable that
supports HEC, the HDMI Ethernet Channel)
Non-volatile EDID storage
Kramer reKlocking™ & Equalization Technology that rebuilds the digital
signal to travel longer distances
Static or dynamic DHCP IP addressing
Embedded Web pages that provide remote configuration and operation
A lock button to prevent unwanted tampering with the buttons on the front
panel
Support for Kramer Protocol 3000

VS-62H - Overview
5
You can control the VS-62H using the front panel buttons, or remotely via:
RS-232 serial commands transmitted by a PC, touch screen system or other
serial controller
The Kramer RC-IR3 infrared, remote control transmitter
A PC connected via a LAN to the Ethernet port on the VS-62H
An optional, external, remote IR receiver (see Section 3.1)
3.1 Using the IR Transmitter
You can use the RC-IR3 IR transmitter to control the machine via the built-in IR
receiver on the front panel or, instead, via an optional external IR receiver (for
example, P/N C-A35M/IRR-50). The external IR receiver can be located up to 15m
away from the machine. This distance can be extended to up to 60m when used
with three extension cables (for example, P/N C-A35M/A35F-50).
Before using the external IR receiver, be sure to arrange for your Kramer dealer to
insert the internal IR connection cable (for example, P/N: 505-70434010-S) with
the 3.5mm connector that fits into the REMOTE IR opening on the rear panel.
Connect the external IR receiver to the REMOTE IR 3.5mm connector.

6
VS-62H - Defining the VS-62H 6x2 HDMI Matrix Switcher
4 Defining the VS-62H 6x2 HDMI Matrix
Switcher
Figure 1 defines the front panel of the VS-62H.
Figure 1: VS-62H 6x2 HDMI Matrix Switcher Front Panel
#
Feature
Function
1
IR LED
Lights yellow when receiving an IR signal
2
IR Sensor
Signal receiver for the infrared remote control transmitter
3
INPUT
SELECTOR
Buttons
TO OUT 2 1~6
Press one of the six inputs to switch it to Output 2
(see Section 8.1).
Press the currently selected input button to mute the output
4
TO OUT 1 1~6
Press one of the six inputs to switch it to Output 1
Press the currently selected input button to mute the output
5
MUTE Button
Press to toggle mute of both output signals (see Section 8.3)
6
EDID Button
Press to capture the EDID (see Section 8.2)
7
ON LED
Lights green when the device is powered on
8
LOCK Button
Press and hold to lock the front panel buttons. Press and hold
again to unlock (see Section 8.4)
9
FUNCTION Button
Press to activate the test pattern generator. When the
generator is active, press one of the input buttons to select a
test pattern