Kramer VP-440H2 User manual

VP-440H2 Enhanced Quick Start (P/N: 2900-300930QS REV 3)
P/N:
2900- 300930QS
Rev:
3
Scan for full manual
VP-440H2 Quick Start Guide
This guide helps you install and use your VP-440H2 for the first time.
Go to www.kramerav.com/downloads/VP-440H2 to download the latest user manual and check if
firmware upgrades are available.
Step 1: Check what’s in the box
VP-440H2 4K Presentation Switcher Scaler
1 Power cord
1 Bracket set
1 Power supply (48V DC)
1 Quick start guide
4 Rubber feet
Step 2: Get to know your VP-440H2
#
Feature
Function
1
48 V () Slide Switch
Slide up (48V) to select a condenser type microphone; slide down to select a dynamic type
microphone (we recommend that you slide down if a microphone is not connected to the
VP-440H2).
2
MIC 6.3mm Jack
Connect to the microphone source.
3
Input Selector
Buttons
HDBT IN
Press to select the HDBT input.
4
HDMI IN
Press to select the HDMI input (from 1 to 3).
5
PC IN
Press to select the computer graphics input.
6
MENU Button
Displays the OSD menu.
7
Navigation
Buttons

Press to decrease numerical values or selectfrom several definitions.
When not in the OSD menu, press to reduce the output volume.

Press to move up the menu list values.

Press to increase numerical values or select from several definitions.
When not in the OSD menu, press to increase the output volume.

Press to move down the menu list.
ENTER
Press to accept changes and change the SETUP parameters.
8
RESET TO XGA/1080p Button
Press and hold for about 5 seconds to toggle the output resolution between XGA and 1080p,
alternatively.
9
PANEL LOCK Button
Press and hold for about 5 seconds to lock/unlock the front panel buttons.

#
Feature
Function
10
CONTROL (Tx, Rx, GND) Terminal
Block Connectors
Connect to the PC orthe serial controller to control the device.
11
HDBT IN (Tx, Rx, GND) Terminal Block
Connectors
Connect to a controller to control peripheral devices that are connected to the HDBT
transmitter (for example, a Blu-ray player connected to WP-20).
12
HDBT OUT(Tx, Rx, GND) Terminal
Block Connectors
Connect to a controller to control peripheral devices that are connected to the HDBT
receiver (for example, a projector connected to TP-580Rxr).
13
AUDIO INPUT
Unbalanced
Stereo 3.5 Mini
Jack
HDMI
Connect to the analog audio HDMI source (from 1 to 3).
14
PC
Connect to the analog audio computer graphics source.
15
AUDIO OUT 3.5 Mini Jack
Connect to an unbalanced stereo audio acceptor.
16
ETHERNET Connector
Connects to the PC or other controller through computer networking.
17
VIDEO INPUT
Connectors
HDBT IN RJ-45
Connect to an HDBT transmitter (for example, WP-20).
Can supply PoE (up to 13W) to the transmitter.
18
HDMI IN
Connect to the HDMI source (from 1 to 3).
19
PC IN on15-pin HD
Connect to the computer graphics source.
20
HDBT OUT RJ-45 Connector
Connect to an HDBT receiver (for example, TP-580Rxr).
21
HDMI OUT Connector
Connect to the HDMI acceptor.
22
48V DC Power Terminal Block
+48VDC connector for powering the unit.
Step 3: Install VP-440H2
To mount the VP-440H2 in a rack, use an RK-1 rack adapter. Alternatively, attach the rubber feet to the underside of the
VP-440H2 and place it on a table.

Step 4: Connect the inputs and outputs
Always switch OFF the power on each device before connecting it to your VP-440H2. For best results, we recommend that you
always use Kramer high-performance cables to connect AV equipment to VP-440H2.
RJ-45 Pinout:
Microphone Pinout:
For the Ethernet connector, see the wiring
diagram below
The microphone 6mm jack pinout for a condenser microphone
The microphone 6mm jack pinout for a dynamic microphone.
PIN EIA /TIA 568B
PIN
Wire Color
1
Orange / White
2
Orange
3
Green / White
4
Blue
5
Blue / White
6
Green
7
Brown / White
8
Brown
For optimum range and performance use the
recommended Kramer cables available at
www.kramerav.com/product/VP-440H2.

Step 5: Connect the power
Connect the 48V DC power adapter power cord to VP-440H2 and plug it into the mains electricity.
Safety Instructions (DC)
Caution:
There are no operator serviceable parts inside the unit.
Warning:
Use only the Kramer Electronics power supply that is provided with the unit.
Warning:
Disconnect the power and unplug the unit from the wall before installing.
See www.KramerAV.com for updated safety information.
Step 6: Control and operate VP-440H2 via the front panel buttons and via
Web pages:
OSD Menu:
Menu
Menu Items
Picture
Adjust contrast brightness and color, and fine-tune the image.
Input
Select input source.
Output
Select method for 4K input to 4K output handling, image size and resolution.
Audio
Select audio source, audio parameters (bass, treble and so on), microphone
settings and volume per input.
OSD
Set OSD position, transparency and so on.
Advanced
Select HDCP on each of the inputs and outputs, manage the EDID and
define IP settings.
Info.
View device information.
Factory
Reset to factory default settings.