Kramer DIP-22 User manual

DIP-22 Quick Start
P/N:
2900- 301038QS
Rev:
4
Scan for full manual
DIP-22 Quick Start Guide
This guide helps you install and use your DIP-22 for the first time.
Go to www.kramerav.com/downloads/DIP-22 to download the latest user manual and check if firmware
upgrades are available.
Step 1: Check what’s in the box
DIP-22 Automatic Video Switcher
1 Bracket set
1 Quick start guide
1 Power adapter and cord
4 Rubber feet
Step 2: Get to know your DIP-22
#
Feature
Function
1
DP++ IN SELECT Button
Press to select the DP++ input. Button lights red when analog audio is selected and
green when embedded audio is selected.
2
DP++ Connector
Connect to a DisplayPort source.
3
HDMI™IN SELECT Button
Press to select the HDMI input. Button lights red when analog audio is selected and
green when embedded audio is selected.
4
HDMI IN Connector
Connect to an HDMI source.
5
PC IN SELECT Button
Press to select the PC graphics input. Button lights red when analog audio is selected
and green when embedded audio from the HDMI IN/DP++ IN is selected.
6
PC IN 15-pin HD Connector
Connect to a computer graphics source.
7
AUDIO IN 3.5mm Mini Jack
Connect to an unbalanced stereo audio source.
8
STEP-IN Button
Press to take control of the input that this device is connected to on a compatible
switcher.
9
ON LED
Lights green when DIP-22 is powered via power adapter or PoE over HDBaseT.
Lights red when DIP-22 provides PoE over HDBaseT to a compatible PoE acceptor.
#
Feature
Function
10
AUDIO OUT 3.5mm Mini Jack
Connect to an unbalanced, stereo audio acceptor.
11
ETHERNET RJ-45 Connector
Connect to a PC via a LAN to control DIP-22.
12
CONTROL (G, Rx, Tx)Terminal
Block Connectors
Connect to the PC or to a serial remote controller to control DIP-22.

13
DATA (G, Rx, Tx)Terminal Block
Connectors
Connect to a serial data source (for example, a room controller) or to an acceptor for
tunneling control commands via HDBaseT.
14
Remote 5-pin Terminal Block
Connector
Connect to contact closure switches (by momentary contact between the desired pin and
G pin).
INPUT –Short press—toggles between the PC, DP++ and HDMI inputs; Long press—
adjusts the VGA phase shift.
STEP-IN –activate the STEP-IN function.
VOL UP, VOL DOWN –Short press—increases/decreases the volume by one step;
Long press—Increases/decreases the volume from 0% to 100%/100% to 10% in 10
seconds.
15
FACTORY RESET Button
Short press –Power cycle (reboot) the device.
Long press –Reset IP settings to factory default values.
16
SETUP 4-way DIP-switches
Set the device behavior.
17
PROG Mini USB Port
Connect to a PC to perform firmware upgrade.
18
HDBT OUT RJ-45 Connector
Connect to an HDBaseT receiver (for example, TP-780Rxr, TP-588D or TP-580Rxr) and
provide or accept power (bidirectional PoE).
19
LINK LED
Lights green when there is a valid HDBT link.
20
48V DC Power Terminal Block
Connector
Connect to the Kramer power adapter.
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
Step 3: Mount DIP-22
Install DIP-22 using one of the following methods:
•Attach the rubber feet and place the unit on a flat surface.
•Fasten a bracket (included) on each side of the unit and attach it to a flat surface
(see www.kramerav.com/downloads/DIP-22).
•Mount the unit in a rack using the recommended rack adapter
(see www.kramerav.com/product/DIP-22).
•Ensure that the environment (e.g., maximum ambient temperature &
air flow) is compatible for the device.
•Avoid uneven mechanical loading.
•Appropriate consideration of equipment nameplate ratings should be
used for avoiding overloading of the circuits.
•Reliable earthing of rack-mounted equipment should be maintained.
•Maximum mounting height for the device is 2 meters.
Step 4: Connect inputs and outputs
Always switch OFF the power on each device before connecting it to your DIP-22.
To achieve specified extension distances, use the recommended Kramer cables available at www.kramerav.com/product/DIP-22.
Using third-party cables may cause damage!
Step 5: Connect power
Connect the power cord to DIP-22 and plug it into the mains electricity.
Safety Instructions (See www.kramerav.com for updated safety information)
Caution:
•For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual.
•There are no operator serviceable parts inside the unit.
Warning:
•Use only the power cord that is supplied with the unit.
•Disconnect the power and unplug the unit from the wall before installing.

Step 6: Operate DIP-22
Operate DIP-22 via:
•Front panel SELECT buttons and STEP-IN button.
•Contact closure switches.
•Remotely, by RS-232 serial commands transmitted by a touch screen system, PC, or other serial controller.
•Embedded web pages via the Ethernet (including Maestro for configuring single-trigger room element automation
scenarios).
Default RS-232 Communication Parameters
Parameter
Values
Baud Rate
115200
Data Bits
1
Stop Bits
1
Parity
None
Command Format
ASCII
Ethernet Parameters
Parameter
Values
IP Address:
192.168.1.39
Subnet Mask:
255.255.0.0
Default Gateway:
192.168.0.1
Default TCP Port #:
5000
Default UDP Port #:
50000
Full Factory Reset
Full Factory Reset
FACTORY RESET Button:
Long press to reset IP settings to factory default values.
Protocol 3000:
“#factory” command.
Web Pages:
In the Device Settings page, click Reset.
Contact Closure Switches:
INPUT—input selection/VGA phase
shift adjustment
Short press—Input toggle
Long press—Adjusts the VGA phase shift
STEP IN
Activates the step-in function if relevant
VOL UP—analog audio output volume
increase control
Short press—Increases the volume one step
Long press—Increases the volume from 0% to 100% in 10 seconds
VOL DN—analog audio output
volume decrease control
Short press—Decreases the volume one step
Long press—Decreases the volume from 100% to 0% in 10 seconds
GND
Connect to the common side of the switches
DIP-switch Setup:
A switch that is down is on; a switch that is up is off. By default, all the switches are up (off).
After changing a DIP-switch you must power cycle the device to implement the change.
Video Switching Selection:
DIP-switch 1
DIP-switch 2
Video Input Selection
Off (up)
Off (up)
Automatic—Last connected. Where more than one source
is connected the last one connected has priority
Off (up)
On (down)
Automatic—Priority selection.
DP++ IN HDMI IN PC IN (default, high to low priority)
On (down)
Off (up)
Manual
On (down)
On (down)
Manual
Audio Switching Selection:
DIP-switch 3
DIP-switch 4
Audio Input Selection
Off (up)
Off (up)
Automatic—Priority selection.
Embedded Audio analog Audio In (high to low priority)
Off (up)
On (down)
Automatic—Priority selection.
Analog Audio In embedded Audio (high to low priority)
On (down)
Off (up)
Embedded Audio
On (down)
On (down)
Analog Audio In

Using Maestro:
Maestro is a powerful software tool that enables you to configure single-trigger room element automation scenarios without
the need for complicated programming. Choose prepared commands from a database, drag and drop the commands to define
actions and execute the actions with predefined triggers.
Maestro turns the device into a much more powerful output device controller. The following table compares the control
capabilities of the non-Maestro and Maestro devices:
Non-Maestro
Maestro
Max. Ports
1
10 (1 RS-232 + 9 Ethernet)
Max. Commands per Action
2
30
Max. Actions
2
20
Scenario configuration follows a simple 4-step process:
1. Configure the ports –Define and configure a DIP-22 communication port to control remote devices:
▪RS-232 and Ethernet –Select and enter the details of the controlled device to control it.
▪Internal –Select to send commands and control the DIP-22.
▪WOL –Select and enter the MAC address of the device you want to Wake-On-LAN.
2. Enter commands –Create commands or use ready-made commands from a database that was preinstalled on a PC
in the network (for example, Audio_Mute_On).
3. Create actions –Create a new action and then drag and drop the created commands to the Editor section to build the
action macro (an action includes a group of commands that is operated according to a trigger).
4. Specify a trigger –Select a trigger from the list of triggers and associate it with a previously defined action (triggers
are the events that cause actions to run.