Kraus KPF-1612 User manual

Single Lever Pull-Out
Kitchen Faucet
KPF-1612
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2017 Kraus USA Inc. I REV. October 25, 2017
INSTALLATION GUIDE

1
Congratulations on the purchase of your new
Kraus plumbing xture!
Please keep teh box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance, or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / customerser[email protected]
Have the model number available, and retain a copy of your receipt
with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE

2
PRIOR TO INSTALLATION
• Make sure you have all necessary parts by checking the diagram and parts
list. If any part is missing or damaged, please contact Kraus Customer
Service at 800-775-0703 for a replacement
• Turn o the hot and cold water supply at the angle stops and turn on the
old faucet to release any built up pressure. Remove existing faucet. Clean
sink or countertop to remove any debris, plumber’s putty, or silicone
• Place bucket under angle stops. Turn on to ush any debris prior to
installing new plumbing. Shut o angle stops
• Pre-drilled hole size requirement: 1-3/8”
• Max countertop thickness without deck plate: 1-3/8”
Tools Required
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [e-mail]
Adjustable Wrench
6 5/8”
5 4/5”
3/8”
(10mm)
7/8”
19.7º(22mm)
8 5/16”
1 1/4-18UNF-2A
(21mm)
10 1/8”
(257mm)
1 3/8”
(35mm)
3 3/4”
(168mm)
(147.3mm)
(96mm)
∅ 1 3/4”
(∅ 45mm)
∅ 1 15/16”
(∅ 50mm)
9/16”-18UNEF
27mm ~ 41.3mm 1 1/16” ~ 1 5/8”
∅ 1 15/16”
(∅ 50mm)
12 7/16”
(316mm)
1 5/8”
(42.5 mm Max)
7A
8B
8C
8D
8A
7A
8B
8C
8D
8A
Silicone Sealant
6 5/8”
5 4/5”
3/8”
(10mm)
7/8”
19.7º(22mm)
8 5/16”
1 1/4-18UNF-2A
(21mm)
10 1/8”
(257mm)
1 3/8”
(35mm)
3 3/4”
(168mm)
(147.3mm)
(96mm)
∅ 1 3/4”
(∅ 45mm)
∅ 1 15/16”
(∅ 50mm)
9/16”-18UNEF
27mm ~ 41.3mm 1 1/16” ~ 1 5/8”
∅ 1 15/16”
(∅ 50mm)
12 7/16”
(316mm)
1 5/8”
(42.5 mm Max)
7A
8B
8C
8D
8A
7A
8B
8C
8D
8A
Phillips Screwdriver Safety Goggles Bucket

3
Diagram and Parts List
A. Faucet Body
B. Base
C. Mounting Hardware Assembly
C1 Rubber Washer
C2 Metal Washer
C3 Mounting Nut
C4 Mounting Screws
D. Weight
E. Spray Head
F. Spray Hose
G. Spring
H. Sprayer Holder
I. Hot and Cold Waterlines
J. Supply Hose
Included Parts:
1. Faucet Body
2. Base O-Ring
3. Rubber Washer
4. Metal Washer
5. Fixing Nut
6. Fixing Screw (2)
7. Weight
8. Spray Head
9. Spray Hose
10. Spring
11. Spring Holder
12. Hot and Cold Waterlines (2)
13. Supply Hose
KPF-1612 Diagram and Parts List
1
2
10
3
4
5
6
7
Hot
Water
Ø35~Ø38
Ø1 3/8~Ø1 1/2”
8 15/32”
inimum distance 3.5”
ess than 3.5”
9
8
11
12
1
10
9
11
12
15
14
13
2
3
4
5
6
7
1
10
9
11
12
15
14
13
2
3
4
5
6
7
8
Wrench Phillips Screwdriver
Tools you will need:
13
A
B
D
C1
C2
C3
C4
E
F
G
H
I
J

4
Faucet Dimensions
Hot
Water
Cold
Water
Ø1-3/8”~Ø1-1/2”
Ø35mm~Ø38mm
8-1/2”
215mm
203mm
8”
Cold Water
Hot Water
35mm~ 38mm
1-3/8”~ 1-1/2“
217mm
8-1/2”
8”
(203mm)
Ø
ØØ
Ø

5
Faucet Dimensions
540mm
Max35mm
Max1-3/8” 21-1/4”
Max35mm
Max1-3/8” 21-1/4”
(540mm)

6
Installation Method 1
Installation Method 2
The minimum distance between
the faucet hole and the wall should
be 3.5”
If the distance between the faucet
hole and the wall is less than 3.5”,
position the faucet lever 30 degrees
to 90 degrees o of the wall to
allow for full operation
Faucet Installation Procedure
1
2
13
10
3
4
5
6
7
Max35
Max 1 3/8”
Hot
Water
Cold
Water
Hot
Water
Ø35~Ø38
Ø1 3/8~Ø1 1/2”
540
21 1/4”
8 15/32”
Minimum distance 3.5”
Less than 3.5”
30˚
Ø35~Ø38
1
2
3
4
5
6
1
2
3
4
5
6
5
6
7
Ø1 3/8~Ø1 1/2”
9
8
11
12
90˚
25˚
O
Left
Hot Water
Right
Cold Water
On
1
2
13
10
3
4
5
6
7
Max35
Max 1 3/8”
Hot
Water
Cold
Water
Hot
Water
Ø35~Ø38
Ø1 3/8~Ø1 1/2”
540
21 1/4”
8 15/32”
Minimum distance 3.5”
Less than 3.5”
30˚
Ø35~Ø38
1
2
3
4
5
6
1
2
3
4
5
6
5
6
7
Ø1 3/8~Ø1 1/2”
9
8
11
12
90˚
25˚
O
Left
Hot Water
Right
Cold Water
On
Installation Method 1
Installation Method 2
The minimum distance between
the faucet hole and the wall should
be 3.5”
If the distance between the faucet
hole and the wall is less than 3.5”,
position the faucet lever 30 degrees
to 90 degrees o of the wall to
allow for full operation
Faucet Installation Procedure
1
2
13
10
3
4
5
6
7
Max35
Max 1 3/8”
Hot
Water
Cold
Water
Hot
Water
Ø35~Ø38
Ø1 3/8~Ø1 1/2”
540
21 1/4”
8 15/32”
Minimum distance 3.5”
Less than 3.5”
30˚
Ø35~Ø38
1
2
3
4
5
6
1
2
3
4
5
6
5
6
7
Ø1 3/8~Ø1 1/2”
9
8
11
12
90˚
25˚
O
Left
Hot Water
Right
Cold Water
On
1
2
13
10
3
4
5
6
7
Max35
Max 1 3/8”
Hot
Water
Cold
Water
Hot
Water
Ø35~Ø38
Ø1 3/8~Ø1 1/2”
540
21 1/4”
8 15/32”
Minimum distance 3.5”
Less than 3.5”
30˚
Ø35~Ø38
1
2
3
4
5
6
1
2
3
4
5
6
5
6
7
Ø1 3/8~Ø1 1/2”
9
8
11
12
90˚
25˚
O
Left
Hot Water
Right
Cold Water
On
Faucet Installation Procedures
Installation Method 1
Installation Method 2 (optional)
The minimum distance
between the faucet hole and
the wall shouldbe 3.5”
If the distance between the
faucet hole and the wall is less
than 3.5”, position the faucet
lever 30 degrees to 90 degrees
off of the wall to allow for full
operation

7
Step 1
Remove mounting screws (6),
mounting nut (5), metal washer
(4), and rubber washer (3) from
the faucet body (1)
1
2
13
10
3
4
5
6
7
Max35
Max 1 3/8”
Hot
Water
Cold
Water
Hot
Water
Ø35~Ø38
Ø1 3/8~Ø1 1/2”
540
21 1/4”
8 15/32”
Minimum distance 3.5”
Less than 3.5”
30˚
Ø35~Ø38
1
2
3
4
5
6
1
2
3
4
5
6
5
6
7
Ø1 3/8~Ø1 1/2”
9
8
11
12
90˚
25˚
O
Left
Hot Water
Right
Cold Water
On
Step 2
Insert the faucet body (1) into
the hole on the deck with the
base o-ring (2). Install the rubber
washer (3), metal washer (4),
mounting nut (5) and mounting
screws (6) from underneath the
sink
1
2
13
10
3
4
5
6
7
Max35
Max 1 3/8”
Hot
Water
Cold
Water
Hot
Water
Ø35~Ø38
Ø1 3/8~Ø1 1/2”
540
21 1/4”
8 15/32”
Minimum distance 3.5”
Less than 3.5”
30˚
Ø35~Ø38
1
2
3
4
5
6
1
2
3
4
5
6
5
6
7
Ø1 3/8~Ø1 1/2”
9
8
11
12
90˚
25˚
O
Left
Hot Water
Right
Cold Water
On
Step 1
Remove mounting screws (6),
mounting nut (5), metal washer
(4), and rubber washer (3) from
the faucet body (1)
1
2
13
10
3
4
5
6
7
Max35
Max 1 3/8”
Hot
Water
Cold
Water
Hot
Water
Ø35~Ø38
Ø1 3/8~Ø1 1/2”
540
21 1/4”
8 15/32”
Minimum distance 3.5”
Less than 3.5”
30˚
Ø35~Ø38
1
2
3
4
5
6
1
2
3
4
5
6
5
6
7
Ø1 3/8~Ø1 1/2”
9
8
11
12
90˚
25˚
O
Left
Hot Water
Right
Cold Water
On
Step 2
Insert the faucet body (1) into
the hole on the deck with the
base o-ring (2). Install the rubber
washer (3), metal washer (4),
mounting nut (5) and mounting
screws (6) from underneath the
sink
1
2
13
10
3
4
5
6
7
Max35
Max 1 3/8”
Hot
Water
Cold
Water
Hot
Water
Ø35~Ø38
Ø1 3/8~Ø1 1/2”
540
21 1/4”
8 15/32”
Minimum distance 3.5”
Less than 3.5”
30˚
Ø35~Ø38
1
2
3
4
5
6
1
2
3
4
5
6
5
6
7
Ø1 3/8~Ø1 1/2”
9
8
11
12
90˚
25˚
O
Left
Hot Water
Right
Cold Water
On
C1
C2
C3
C4
A
Remove mounting hardware
assembly (C)
Insert faucet body (A) into hole
on deck or sink with base (B)
attached. Attach mounting
hardware assembly (C)
C1
C2
C3
C4
A
B
Step 1
Step 2

8
Step 3
Step 4
After adjusting the direction of
the faucet body (1), tighten the
mounting nut (5) until snug and
tighten the mounting screws (6)
to the nut with a Philips head
screwdriver
Connect the spray hose (9) to
the supply line and tighten with
a wrench until snug, then install
the weight (7) at the lowest point
(horizontally) on the spray hose
(12)
Hot
Water
1
2
3
4
5
6
5
7
5
6
7
J
F
Step 3
Step 4
After adjusting the direction of
the faucet body (1), tighten the
mounting nut (5) until snug and
tighten the mounting screws (6)
to the nut with a Philips head
screwdriver
Connect the spray hose (9) to
the supply line and tighten with
a wrench until snug, then install
the weight (7) at the lowest point
(horizontally) on the spray hose
(12)
Hot
Water
1
2
3
4
5
6
5
7
5
6
7
J
F
Adjust faucet body. Secure
mounting hardware (C) with
wrench and Phillips head
screwdriver
Connect spray hose (F) to supply
hose (J) and tighten. Attach
weight (D) to lowest point
vertically on spray hose (F)
C
D
Step 3
Step 4

9
Step 5
Connect hot and cold waterlines (12) to the angle stops and tighten with
a wrench until snug, then unscrew spray head (8), hold the tip of the spray
hose (9) and turn on the faucet to ush any debris
6 5/8”
5 4/5”
3/8”
(10mm)
7/8”
19.7º(22mm)
8 5/16”
1 1/4-18UNF-2A
(21mm)
10 1/8”
(257mm)
1 3/8”
(35mm)
3 3/4”
(168mm)
(147.3mm)
(96mm)
∅ 1 3/4”
(
∅ 45mm)
∅ 1 15/16”
(
∅ 50mm)
9/16”-18UNEF
27mm ~ 41.3mm 1 1/16” ~ 1 5/8”
∅ 1 15/16”
(
∅ 50mm)
12 7/16”
(316mm)
1 5/8”
(42.5 mm Max)
7A
8B
8C
8D
8A
7A
8B
8C
8D
8A
Usage
How to Operate the Handle
1. Pull the lever to the right to
turn on the water. Push to the
left to turn o
2. Pull the lever forward
to increase hot water ow
and push the lever back to
increase the cold water ow
1
2
13
10
3
4
5
6
7
Max35
Max 1 3/8”
Hot
Water
Cold
Water
Hot
Water
Ø35~Ø38
Ø1 3/8~Ø1 1/2”
540
21 1/4”
8 15/32”
Minimum distance 3.5”
Less than 3.5”
30˚
Ø35~Ø38
1
2
3
4
5
6
1
2
3
4
5
6
5
6
7
Ø1 3/8~Ø1 1/2”
9
8
11
12
90˚
25˚
O
Left
Hot Water
Right
Cold Water
On
1
2
13
10
3
4
5
6
7
Max35
Max 1 3/8”
Hot
Water
Cold
Water
Hot
Water
Ø35~Ø38
Ø1 3/8~Ø1 1/2”
540
21 1/4”
8 15/32”
Minimum distance 3.5”
Less than 3.5”
30˚
Ø35~Ø38
1
2
3
4
5
6
1
2
3
4
5
6
5
6
7
Ø1 3/8~Ø1 1/2”
9
8
11
12
90˚
25˚
O
Left
Hot Water
Right
Cold Water
On
9
Step 6
Hot
Water
Cold
Water
Installer Tip
F
E
G
F
Hexagon Nut
Hot
Water
Cold
Water
Close
Open Left
Hot Water
Push
25˚ 90˚
Step 5
KPF-1602.indd 9 2016-08-09 3:39 PM
A
J
Remove spray head (E) and
turn faucet on for 60 second
to flush any debris
Step 5
How to operate the handle:
Usage
1. Pull the lever to the right to
turn on the water. Push to the
left to turn off
2. Pull the lever forward
to increase hot water flow
and push the lever back to
increase the cold water flow
Connect and tighten waterlines
(I) to angle stops. Turn on the
angle stops and check for leaks
(DO NOT TURN FAUCET ON)