Kraus Britt KPF-1691 User manual

INSTALLATION MANUAL
Britt™ Single Handle
Commercial Style Kitchen
Faucet
KPF-1691
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2023 Kraus USA Plumbing LLC
I Rev. March 29, 2023

2
Congratulations on the purchase of your new
R
Kraus plumbing fixture!
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / [email protected]
Have the model number available and retain a copy of your
receipt with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
STOP

13
3
Prior to Installation:
·Make sure you have all necessary parts by checking the diagram and
parts list. If any part is missing or damaged, please contact Kraus
Customer Service at 800-775-0703 for a replacement.
·Read all instructions and safety warnings and ensure you have all tools,
parts, and equipment necessary for a safe installation.
·Turn off the hot and cold water supply at the angle stops and turn on
the old faucet to release any built up pressure. Remove existing faucet.
·Pre-drilled hole size requirement: 1 3/8" (min)
·Max countertop thickness: 3 1/8”
Care & Maintenance
* To keep the product clean & shining, follow the steps below:
1. Rinse with clean water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives or harsh cleaners
3. Do not use cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
* This installation manual is subject to change without further notice.
ACID
R
STOP
For technical assistance or replacement parts, please contact Kraus Customer
Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]
Tools Required
Wrench Phillips Screwdriver Silicone Sealant Safety Goggles Pipe Tape

B
K
C
A. Spray Head
B. Faucet Body
C. Flange
D. Rubber Washer
E. Metal Washer
F. Mounting Nut
D
E
F
G
I
J
G. Screws
H. Weight
I. Weight Clip
J. Quick Connector
K. Hex Wrench
H
A
Diagram and Parts List
4

Faucet Dimensions
3/8” compression
3 1/8"
[80.3mm]
22 1/4"
[565.4mm]
8 3/8"
[213.6mm]
10 5/8"
[268.9mm]
6 1/2"
[164.3mm]
4 1/4"
[108.8mm]
Ø2 1/8"
[54.2mm]
Installer Tip:
Shut off main water supply before installing new faucet.
5

G
Step 1: Installing the faucet
Shut off the water supply. Place the
faucet (B) through the hole in the sink
or countertop. Secure the faucet (B) to
the sink or countertop using the rubber
washer (D), metal washer (E) and
mounting nut (F) provided. Tighten
screws (G). Do not overtighten.
Step 2: Securing the faucet assembly
Push the quick connector (J) firmly
upward and attach it to the receiving
block (a). Pull down moderately to
ensure the connection has been made.
D
E
G
B
F
a
J
(2N.m
Max)
6

Install the weight clip (I) at the point of
the hose marking "weight here". Insert the
weight (H) onto the weight clip (I) by
sliding it down onto the weight clip (I).
Attach waterlines to angle stops
and tighten until snug. Turn on angle
stops and check for leaks (DO NOT TURN
FAUCET ON).
Weight
here
Weight
here
I
H
NOTE: Please make sure filter washers
are installed before connecting to the
main valve.
Step 3: Installing the counterweight
Step 4: Connect waterlines to main valve
7

Pull the hose assembly out of the spout
and remove the spray head (A) by
unscrewing it from the hose in a
counterclockwise direction. Be sure to hold
the end of the hose down into the sink
and turn the faucet on to the warm
position where it mixes hot and cold water.
Flush the water lines for one minute. This
flushes away any debris that could cause
damage to internal parts. Check for leaks.
Retighten any connections if necessary,
but do not overtighten. Reinstall the spray
head (A) by hand tightening it back onto
the spray hose.
After installation is complete, turn on the
hot and cold water supplies. Check for
leaks.
NOTE: Please make sure washer is
installed attaching spray head to hose.
A
Step 5: Flush faucet
8

Replacement Parts
1. Sprayer Head
Replacement Parts List Part #
2. Washer
3. Inverter
5. Spring Assembly
6. Screw
7. Index
9. Bonnet Nut
10. Cap & O-ring
11. Handle
Finish / Color
KP27243
KP27084
KP27124
KP27083
KP27238
KP27239
KP27195
KP27208
KP27242
8. Cartridge
4. Sprayer Hose KP27244
12. Screw
KP27240
KP27001
SFACB, BB, SFSB
SFS, MB**
13. Index KP27002
SFACB, BB,
SFS, MB**
14. Hex Wrench
15. Flange & Washer
KP27020
16. Rubber & Metal Washer
KP27041
KP27028
17. Mounting Nut & Screw
18. Block
KP27079
19. O-Ring
KP27073
KP27092
20. 1.8GPM Flow Restrictor
21. Quick Connector
Assembly
KP27074-WH
KP27090
WHITE
6
7
1
8910
11
12
13
14
18
19
20
2
15
16
17
22
21
23
3
4
5
BL, GR**
22. Weight & Clip Assembly KP27212
23. Filter Washer KP27167
SFACB, BB, SFSB
SFS, MB**
BL, GR**
SFACB, BB, SFSB
SFS, MB**
BLSFACB,GRSFS
BLMB, BLBB,BLSFS*
SFACB, BB, SFSB
SFS, MB**
BL, GR**
*Denotes spray hose assembly color options:
Spray hose assembly color options:
Black hose with Matte Black connector (BLMB);
Gray hose with Spot-Free Stainless connector
(GRSFS); Black hose with Spot-Free Stainless
connector (BLSFS); Black hose with Spot-Free
Antique Champagne Bronze connector
(BLSFACB); Black hose with Brushed Brass
connector (BLBB)
**Denotes faucet component color options:
SFS - Spot Free Stainless SteelSF
MB - Matte Black
SFSB - Spot Free Black Stainless
SFACB - Spot Free Antique Champagne Bronze
BB - Brushed Brass
SFSMB - Spot Free Stainless Steel/Matte Black
MBSFSB - Matte Black/Spot Free Black Stainless
GR - Grey
BL - Black
9

Troubleshooting
If you have followed the instructions carefully and your faucet still does not work properly,
take the following corrective steps:
Leakage under the handle.
PROBLEM CAUSE ACTION
Bonnet nut () has
come loose. 5HPRYHWKHLQGH[/RRVHQWKH
VFUHZZLWKWKHKH[ZUHQFK
5HPRYHWKHKDQGOH8QVFUHZWKH
FDSE\KDQGRQO\7LJKWHQ
ERQQHWQXWZLWKDQDGMXVWDEOH
ZUHQFK
The aerator has an irregular
or reduced water flow.
The aerator is dirty or
misfitted.
Remove the aerator and check for debris.
Ensure that the rubber washer is properly
installed.
Water will not shut off
completely.
Cartridge may need to be
adjusted or replaced.
5HPRYHWKHLQGH[/RRVHQWKH
VFUHZZLWKWKHKH[ZUHQFK
5HPRYHWKHKDQGOH8QVFUHZWKH
FDSE\KDQGRQO\/RRVHQWKH
ERQQHWQXWZLWKDQDGMXVWDEOH
ZUHQFK5HPRYHWKHFDUWULGJH
&KHFNIRUFUDFNV
There is a low flow of water. The filter washers in the
hose connectors are dirty.
Turn off the water supply at the water
valves and unscrew the hose connectors
from the water supply lines. Clean the
ILOWHUwashers in the water lines with hot
water, removing any debris or calcium
build up.
10