Kraus Urbix KPF-3125-FF-101BG User manual

UrbixTM Industrial Bridge
Kitchen Faucet
KPF-3125
R
INSTALLATION MANUAL
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2023 Kraus USA Plumbing LLC I REV. April 3, 2023

2
Congratulations on the purchase of your new
Kraus plumbing fixture!
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / [email protected]
Have the model number available and retain a copy of your
receipt with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
STOP
R

Prior to Installation:
·Make sure you have all necessary parts by checking the diagram and parts list. If any
part is missing or damaged, please contact Kraus Customer Service at 800-775-0703
for a replacement.
·Read all instructions and safety warnings and ensure you have all tools, parts, and
equipment necessary for a safe installation.
·Turn off the hot and cold water supply at the angle stops and turn on the old faucet
to release any built up pressure. Remove existing faucet. Clean sink or countertop to
remove any debris, plumber’s putty, or silicone.
·Flush angle stops to release any debris prior to installation.
·Pre-drilled hole size requirement: 1 1/4" (min) - 1 1/2" (max)
·Max countertop thickness: 2 1/2”
·3 or 4 hole installation
3
Tools Required
Adjustable Wrench Phillips Screwdriver Silicone Sealant Safety Goggles
Care & Maintenance
To keep the product clean & shining, follow the steps below:
1. Rinse with clean water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives or harsh cleaners
3. Do not use cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
This installation manual is subject to change without further notice.
ACID
STOP
R

44
Diagram and Parts List
1. Faucet Body
2. Side Sprayer
3. Sprayer Hose
4. Quick Connector
5. Plug (for NO side sprayer installation)
6. Rubber & Metal Washer
7. Mounting Nut & Screws
1
2
6
7
3
5
4

55
Faucet Installation Procedure
Installer Tip:
Shut off main water supply before installing new faucet.
2 1/8"
(53mm)
typ.
4"
(102mm)
4"
(102mm)
4"
(102mm)
5 1/2"
(139.8mm)
10 1/4"
(258.92mm)
8 3/8"
(213.04mm)
9 3/4"
(248.96mm)
11 3/8"*
(288mm)
12 3/8"*
(313.4mm)
11 3/8"
(288.11mm)
14 1/8" (359.98mm)
* - Adjustable height range.

66
NO Side Sprayer Option
Step 1. Drill countertop
Step 2. Install faucet assembly
Drill 3 holes into the countertop
for the faucet body (1).
Install the faucet assembly
through the holes in the
countertop.
3

7
Step 3. Secure faucet assembly
Secure the faucet body (1) with the
rubber and metal washers (6) and
the mounting nuts and screws (7).
Do not overtighten. Make sure the
plug (5) is installed tightly.
Skip to Step 7.
1
6
7
5
Side Sprayer Option
Step 4. Drill countertop and install side sprayer support
Drill 4 holes into the countertop
for the faucet body (1) and side
sprayer (2). Install the side sprayer
support.
6
7

8
Step 5. Install faucet assembly
Install the faucet assembly
through the holes in the
countertop. Remove plug (5) and
install quick connector (4).
Connect the sprayer hose (3).
1
3
3
4
Step 6. Secure faucet assembly
Secure the faucet body (1) with the
rubber and metal washers (6) and
the mounting nuts and screws (7).
Do not overtighten.
6
7

9
Step 7. Connect waterlines
Connect waterlines to angle
stops. Tighten with a wrench
until snug. Turn on hot and
cold angle stops and check
for leaks.
NOTE: Make sure filter washers
are installed.
Step 8. Flush waterway
Remove the aerator from the
spout. Turn faucet on and let the
water run for 60 seconds to flush
any debris.

10
Step 9. Adjusting spout height
Unthread the holding nut (1) and
pull the spout (2) up. Thread the
holding nut (1).
1
2
1
NOTE: The adjustment
can be up to 1". Lock to
the desired location. It is
recommended to set
and forget, so the
grease does not get
worn. It is recommended
to wipe the spout after
setting the height.