Kraus Esina KPF-1670 User manual

www.kraususa.com I Toll Free: 1.800.775.0703 I © 2022 Kraus USA Plumbing LLC I REV. April 6, 2022
EsinaTM Single Handle
Pull-Down Kitchen Faucet
KPF-1670
R
INSTALLATION MANUAL

2
Congratulations on the purchase of your new
Kraus plumbing fixture!
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / [email protected]
Have the model number available and retain a copy of your
receipt with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
STOP
R

Prior to Installation:
·Make sure you have all necessary parts by checking the diagram and parts list. If any
part is missing or damaged, please contact Kraus Customer Service at 800-775-0703
for a replacement.
·Read all instructions and safety warnings and ensure you have all tools, parts, and
equipment necessary for a safe installation.
·Turn off the hot and cold water supply at the angle stops and turn on the old faucet to
release any built up pressure. Remove existing faucet. Clean sink or countertop to
remove any debris, plumber’s putty, or silicone.
·Flush angle stops to release any debris prior to installation.
·Pre-drilled hole size requirement: 1 3/8" (min) - 1 1/2" (max)
·Max countertop thickness without deck plate: 2 1/4”
·Max countertop thickness with deck plate: 1 3/4”
·1, 2 or 3 hole installation
3
Tools Required
Adjustable Wrench Phillips Screwdriver Silicone Sealant Safety Goggles
Care & Maintenance
To keep the product clean & shining, follow the steps below:
1. Rinse with clean water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives or harsh cleaners
3. Do not use cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
This installation manual is subject to change without further notice.
ACID
STOP
R

44
Diagram and Parts List
1. Spray Head
2. Faucet Body
3. Deck Plate Assembly
A. Deck Plate
B. Base Plate
4. Mounting Hardware
A. Rubber & Metal
Washer
B. Mounting Nut
C. Mounting Screws
5. Spray Hose
6. Weight
7. Quick Connector
8. Hot and Cold
Copper Lines
A. Cold
B. Hot
9. Hex Wrench
10. Washer
11. Hot & Cold Waterlines
610
1
9
11
2
5
8B
8A
7
3A
3B
4A
4B
4C
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]
R

55
Faucet Installation Procedure
Installer Tip:
Shut off main water supply before installing new faucet.
8 3/4"
(224mm)
9 5/8"
(247mm)
16 5/8" (425mm)
8 1/4"
(209mm)
Ø1 3/8"~ 1 1/2"
(35mm~ 38mm)
MAX
2 1/4"
(57mm)
11 1/8" (283mm) 5 3/8"
(136mm)
100°
5°
2 3/4"
(70mm)
Ø1 3/8" (35mm)
10 3/8"
(264mm)
1/2"
(12mm)
* Optional Deck Plate
2X G1/2"

66
Step 1A. Faucet installation - with deck plate
Step 1B. Faucet installation - without deck plate
For three-hole installation:
Deck plate (3A), base plate
(3B), and silicone sealant
(optional) are required.
For single-hole installation:
Deck plate (3A), base plate
(3B) and silicone sealant
are NOT required.
3A
3B

7
Step 2. Install faucet and mounting hardware
Insert faucet body (2) into
hole in countertop or deck
plate assembly (3). Install
mounting hardware (4A, B
& C) from underneath the
countertop.
Step 3. Secure mounting hardware
Adjust direction of faucet
body (2) so that handle is on
right side of faucet. Tighten
mounting nut (4B) until snug.
Tighten mounting screws
(4C) to nut with a Phillips
screwdriver until snug.
4A
4B
4C
4B
4C

8
Step 4. Attach spray hose and counterweight
Step 5. Connect waterlines
Connect spray hose (5)
to quick connector (7)
attached to supply line.
Install weight (6) on lowest
vertical point on spray
hose (5).
Connect waterlines to hot and
cold copper lines (8). Connect
waterlines to angle stops.
Tighten both ends of
waterlines with a wrench until
snug. Turn on hot and cold
angle stops and check for leaks.
7
5
6
8
NOTE: Please make sure filter
washers are installed before
connecting to the main valve.

9
Step 6. Flush spray hose
Remove spray head (1) from
spray hose (5). Hold tip of spray
hose (5). Turn faucet on and let
the water run for 60 seconds to
flush any debris.
Step 7. Check for Leaks
Check for leaks at the
connections. Retighten if
necessary.
NOTE: Please make sure washer (10) is
installed attaching spray head to hose.
5
1

10
Replacement Parts
1. Spray Head
2. Check Valve
3. Spray Hose
4. Hose Guide
6. Handle Button
7. Set Screw
8. Metal Handle
9. Cartridge Cover
10. Locking Nut
12. Cartridge
13. Cartridge Housing
15. Deck Plate
16. Base Plate
17. Protective Sleeve
22. Weight
23. Hex Wrench
26. Check Valve
27. Quick Connector
25. Washer
Replacement Parts List Finish/Color Part #
KP06089
KP06107
KP06098
KP06007
KP06070
KP06030
KP06055
KP06037
KP06082
KP06078
KP06069
KP06100
KP06005
KP06065
KP06008
KP06011
KP06056
KP06041
KP06028
KP06067
KP06068
KP06015
KP06050
KP06094
KP06074
KP06104
KP06108
KP06200
KP06185
SFS, MB*
24. Hot & Cold Waterlines
23
25
22
4
3
2
15
6
7
13
14
12 11 10 98
15
16
17 26
27
24
5. Plastic Clip
11. Washer
14. Rubber O-Ring
SFS, MB*
SFS, MB*
SFS, MB*
SFS, MB*
SFS, MB*
*Denotes faucet component color options:
SFS - Spot Free Stainless Steel
MB - Matte Black
28. Mounting Hardware Kit
(includes KP06041,KP06028
KP06067,KP06068)
18. Rubber Washer
20. Mounting Nut
21. Mounting Screws
19. Metal Washer
18
19
20
21
29. Filter Washers
29