Kraus Crespo KPF-2720 User manual

INSTALLATION MANUAL
KPF-2720
Crespo™ Single Lever Pull Down
Kitchen Faucet
www.kraususa.com I toll free: 1.800.775.0703 I © 2014-2015 Kraus USA Inc. I REV. March 30, 2017

1
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]
Thank you for your purchase
We would like to take this opportunity to thank you for choosing Kraus.
We hope that you are completely satised with your purchase, and enjoy it for years
to come. If you have any questions, or require technical assistance, please contact
us at 800.775.0703 and one of our representatives will be happy to help.
For more information about Kraus products, please visit:
www.kraususa.com
In order to activate your warranty and get faster access to customer support, please
register your new Kraus product at:
www.kraususa.com/registration
Sincerely,
Kraus USA Customer Service

2
Prior to Installation:
• Make sure you have all necessary parts by checking the diagram and parts list.
If any part is missing or damaged, please contact Kraus Customer Service at
800-775-0703 for a replacement
• Turn o the hot and cold water supply at the angle stops and turn on the old
faucet to release any built up pressure. Remove existing faucet. Clean sink or
countertop to remove any debris, plumber’s putty, or silicone
• Place bucket under angle stops. Turn on to ush any debris prior to installing new
plumbing. Shut o angle stops
• Pre-drilled hole size requirement: 1-3/8” (min) – 1-1/2” (max)
• Max countertop thickness without deck plate: 1-1/2”
• Max countertop thickness with deck plate: 1”
• 1, 2, or 3 hole installation
Without deck plate:
With deck plate:
1/16” (1mm) min.
1-1/2” (38 mm) max.
Ø 1-3/8” (35 mm) min.
Ø 1-1/2” (38 mm) max.
1/16” (1mm) min.
1” (25.4 mm) max.
Ø 1-3/8” (35 mm) min.
Ø 1-1/2” (38 mm) max.
1
2
Designated Mark
Hot
Upward
Black
Cold
1A 1B
234
567
G
G
EEF
G
G
G
G
F
F
F
E
E
H
E
E
A
A
I
B
J
D
D
CD
G
Half Moon Locking Nuts Half Moon Locking Nuts
Rubber Caps
G
Tools you will need:
Adjustable Wrench Safety Goggles Bucket Silicone Sealant
6 5/8”
5 4/5”
3/8”
(10mm)
7/8”
19.7
º
(22mm)
8 5/16”
1 1/4-18UNF-2A
(21mm)
10 1/8”
(257mm)
1 3/8”
(35mm)
3 3/4”
(168mm)
(147.3mm)
(96mm)
∅ 1 3/4”
(∅ 45mm)
∅ 1 15/16”
(∅ 50mm)
9/16”-18UNEF
27mm ~ 41.3mm 1 1/16” ~ 1 5/8”
∅ 1 15/16”
(∅ 50mm)
12 7/16”
(316mm)
1 5/8”
(42.5 mm Max)
7A
8B
8C
8D
8A
7A
8B
8C
8D
8A
Adjustable wrench Phillips screwdriver
Tools You Will Need
Hex wrenchSilicone Sealant
A
I
D
J
F
B
G
C
H
E

3
A
C
B
D
J
EF
G
H
I
Diagram and Parts List
A. Spray Head
B. Faucet Body
C. Deck & Putty Plate
D. Base
E. Spray Hose
F. Supply Hose
G. Hot & Cold Waterlines
H. Weight
I. Quick Connect
J. Hex Wrench Set
J1. 2.5mm
J2. 4mm

4
9/16-24 UNEF
(3/8” Compression)
Check Value
1/16”~1-1/8”
(1mm~30mm)
1-5/8”
(40mm)
2-1/2”
(63mm)
10-1/8”
(257mm)
8-3/8”
(213.5mm)
10-1/8”
(258mm)
4-3/8”
(110mm)
8-1/4”
(209mm)
6-5/8
(169.5mm)
10
º
24-1/2”
(622.7mm)
16-1/4”
(413mm)
Faucet Dimensions

5
Step 1A: Install base without deck & putty plate
Insert base (D) into sink or
countertop with “FR↑NT” facing
forward. Tighten screws on base
(D) with 4mm hex wrench (J)
until base is secure on sink or
countertop
Without deck plate:
With deck plate:
1/16” (1mm) min.
1-1/2” (38 mm) max.
Ø 1-3/8” (35 mm) min.
Ø 1-1/2” (38 mm) max.
1/16” (1mm) min.
1” (25.4 mm) max.
Ø 1-3/8” (35 mm) min.
Ø 1-1/2” (38 mm) max.
1
2
Designated Mark
Hot
Upward
Black
Cold
1A 1B
234
567
G
G
EEF
G
G
G
G
F
F
F
E
E
H
E
E
A
A
I
B
J
D
D
CD
G
Half Moon Locking Nuts
Half Moon Locking Nuts
Rubber Caps
G
Installer Tip: Rotate the
two half-moon shaped
locking nuts inward before
inserting base (D) into sink or
countertop

6
Step 1B: Install base with deck & putty plate
Place a bead of clear silicone
sealant (not included) around the
edge of the putty plate (C). Secure
deck & putty plate (C) on sink or
countertop. Insert base (D) into
hole of deck & putty plate (C) with
“FR↑NT” facing forward. Tighten
screws on base (D) with 4mm hex
wrench (J) until base is secure on
deck & putty plate (C)
Without deck plate:
With deck plate:
1/16” (1mm) min.
1-1/2” (38 mm) max.
Ø 1-3/8” (35 mm) min.
Ø 1-1/2” (38 mm) max.
1/16” (1mm) min.
1” (25.4 mm) max.
Ø 1-3/8” (35 mm) min.
Ø 1-1/2” (38 mm) max.
1
2
Designated Mark
Hot
Upward
Black
Cold
1A 1B
234
567
G
G
EEF
G
G
G
G
F
F
F
E
E
H
E
E
A
A
I
B
J
D
D
CD
G
Half Moon Locking Nuts
Half Moon Locking Nuts
Rubber Caps
G
Installer Tip: Rotate the two
half-moon shaped locking
nuts inward before inserting
base (D) into deck plate (C)
Please Note: After base (D) is
secure, remove clip

7
Step 2: Install faucet
Step 3: Secure faucet
Remove Quick Connect (I)
from spray hose (E). Insert
spray hose (E) into small hole
of base (D). Insert hot & cold
waterlines (G) and supply hose
(F), one by one, in large hole
of base
Align arrow on faucet body (B)
with arrow on base (D). Attach
faucet body (B) to base (D) and
turn counter-clockwise. Secure
faucet body (B) by tightening
the set screw with 2.5mm hex
wrench (J)
G
G
G
G
F
F
B
D
E
F
F
E
I
I
I
J
B
D
Hot Cold
G
G
Designated Mark
H
E
A
E
A
E
Rubber Cap
Installer Tip: Please
loosen set screw from
faucet body (B) prior to
securing to base (D)
Note: “ “ on base should be in
alignment with “ “ on faucet body.
Rotate faucet counterclockwise
to secure on base.

8
Step 4: Connect waterlines to main valve
Step 5: Connect quick connect
Thread hot & cold waterlines
(G) onto angle stops. Tighten
with adjustable wrench until
snug. Turn on the angle stops
and check for leaks (DO NOT
TURN FAUCET ON)
Attach Quick Connect (I) to
spray hose (E). Attach the
other end onto the supply
hose (F) until you hear a click
Installer Tip: Tug on the
spray hose (E) moderately
to ensure connection is
secure
Installer Tip: Please
remove rubber cap from
supply hose (F) prior to
installing quick connect (I)
G
G
G
G
F
F
B
D
E
F
F
E
I
I
I
J
B
D
Hot Cold
G
G
Designated Mark
H
E
A
E
A
E
Rubber Cap
G
G
G
G
F
F
B
D
E
F
F
E
I
I
I
J
B
D
Hot Cold
G
G
Designated Mark
H
E
A
E
A
E
Rubber Cap
G
G
G
G
F
F
B
D
E
F
F
E
I
I
I
J
B
D
Hot Cold
G
G
Designated Mark
H
E
A
E
A
E
Rubber Cap
Installer Tip: Use two
wrenches when securing
waterlines to angle stops to
prevent kinking, as shown in
picture
G

9
Step 6: Install weight
Step 7: Flush faucet
Attach weight (H) on the
designated mark on the spray
hose (E)
Remove spray head (A). Hold tip
of spray hose (E). Turn faucet on
for 1 minute to ush any debris.
Reconnect spray head (A)
G
G
G
G
F
F
B
D
E
F
F
E
I
I
I
J
B
D
Hot Cold
G
G
Designated Mark
H
E
A
E
A
E
Rubber Cap
G
G
G
G
F
F
B
D
E
F
F
E
I
I
I
J
B
D
Hot Cold
G
G
Designated Mark
H
E
A
E
A
E
Rubber Cap
G
G
G
G
F
F
B
D
E
F
F
E
I
I
I
J
B
D
Hot Cold
G
G
Designated Mark
H
E
A
E
A
E
Rubber Cap