Kraus KPF-1675 User manual

www.kraususa.com I Toll Free: 1.800.775.0703 I © 2018 Kraus USA Inc. I REV. August 13, 2018
INSTALLATION MANUAL
Single Handle Kitchen Faucet
KPF-1675

1
Congratulations on the purchase of your new
Kraus plumbing xture!
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance, or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / customerser[email protected]
Have the model number available, and retain a copy of your receipt
with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE

2
Prior to Installation:
• Make sure you have all necessary parts by checking the diagram and parts
list. If any part is missing or damaged, please contact Kraus Customer
Service at 800-775-0703 for a replacement
• Turn o the cold and hot water at the angle stops and turn on the old
faucet to release any built up pressure
• Flush angle stops to release any debris prior to installation
• Pre-drilled hole size requirement: 1-3/8” (min) – 1-1/2” (max)
• Max countertop thickness: 1-3/8
• 1 hole installation and 2 or 3 with optional deck plate (not included)
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]

3
Diagram and Parts List
Tools you will need
1
10
279
10 31/32”
Minimum distance 90mm
Less than 90mm
Cold Water
32 3/32”
Ø35~Ø38
1
23
10
9
11
12 13
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
45
7
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10 11
Close
Open Left
Hot Water
Push
25˚ 90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12 13
2
3
4
5
6
7
8
Adjustable
Wrench
Phillips
Screwdriver
Safety
Goggles
Silicone Sealant
(optional)
1. Spray Head
2. Faucet Body
3. Hot and Cold
Copper Lines
A. Hot
B. Cold
4. Quick Connector
5. Mounting
Hardware
A. Rubber &
Metal Washer
B. Mounting Nut
C. Mounting
Screws
6. Hot & Cold
Waterlines
7. Spray hose
8. Weight
9. Hex Wrench
1
2
6
9
8
7
3A
3B
4
5A
5B
5C

4
Faucet Dimension
Installer Tip:
Shut o main water supply before installing new faucet
4 5/8”
117mm
11 1/4”
287mm
9 3/8”
238mm
2”
52mm
2”
52mm
16 1/2”
419mm
10 1/2”
268mm
8 3/8”
212mm
2 x 1/2-14NPSM
1 3/8” ~1 1/2”
35~38mm
1 3/8”
Max35mm

5
Step 1: Remove mounting hardware
Remove the mounting
screws (5C), mounting nut
(5B), and rubber & metal
washer (5A) from the
mounting pipe
5A
5B
5C
Step 2A: Faucet installation - with deck plate
For three-hole installation:
Deck plate, base plate
(see below), and silicone
sealant (optional) are
required
Note: optional deck plate
DP01, not included

6
Step 2B: Faucet installation - without deck plate
For single-hole installation:
Deck plate, base plate, and
silicone sealant are NOT
required
Step 3: Install faucet and mounting hardware
Insert faucet body (2) into
hole in countertop or deck
plate assembly . Install
mounting hardware (5A, B
& C) from underneath the
countertop
5A
5B
5C

7
Step 4: Secure mounting hardware
Adjust direction of faucet
body (2) so that handle is on
right side of faucet. Tighten
mounting nut (5B) until snug.
Tighten mounting screws
(5C) to nut with Phillips
screwdriver until snug
Step 5: Attach spray hose and counterweight
Connect spray hose (7)
to quick connector (4)
attached to supply line.
Install weight (8) on lowest
vertical point on spray
hose (7)
5C
5B
4
78

8
3
6
Connect waterlines (6) to
hot and cold copper lines
(3). Connect waterlines
(6) to angle stops. Tighten
both ends of waterlines
with a wrench until snug.
Turn on hot and cold angle
stops and check for leaks
Step 6: Connect waterlines
Step 7: Flush spray hose
Remove spray head (1) from
spray hose (7). Hold tip of
spray hose (7). Turn faucet on
and let the water run for 60
seconds to ush any debris
1
7

9
Step 8: Check for leaks
Check for leaks at the
connections. Retighten if
necessary