Kraus KWU210-57 User manual

R
INSTALLATION MANUAL
KWU210-57
Kore Workstation Stainless Steel
Undermount Kitchen Sink
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2018 Kraus USA Inc. I REV. October 26, 2020

Congratulations on the purchase of your new Kraus plumbing fixture!
Please keep the box and packaging materials until your product is completely installed. If you have
any questions, require technical assistance or have any problems with your product:
2
Please contact our Customer Service Team
1-800-775-0703 / [email protected]
Have the model number available and retain a copy of your receipt with purchase date for
reference.
If for any reason this product does not meet your expectations, please be sure to repack this
product in the original box and packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
STOP

3
For technical assistance or replacement parts, please contact Kraus Customer Service
and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]
The step-by-step guidelines in the installation instructions are a general reference for installing a Kraus sink. Should
there be any discrepancies, Kraus cannot be held liable. It is recommended to install all Kraus products by hiring a
licensed professional.
Prior to Installation:
·Make sure that you have all necessary parts by checking the parts list. If any part is
missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a
replacement
·Inspect the sink prior to installation to make sure that it has not been damaged or during
shipping
·Use the cut-out template provided by Kraus
·Observe all plumbing and building codes according to your state requirements
·Not recommended to be installed with laminate countertop
Tools you will need:
NOTE: Specialized tools may be necessary to install Kraus Stainless Steel Kitchen sinks with
countertop materials other than wood, marble or granite.
Safety Goggles Silicone Adhesive Jig Saw
Phillips Screwdriver Tape Measure Pencil
Drill Scissors
Screwdriver Putty Knife

44
19" (482.6mm)
Model #: KWU210-57
Sink Dimensions: 57” x 19” x 10”
Min Cabinet Size: 60”
10"
(254mm)
10 1/2"
(266.5mm)
8 3/4"
(222.3mm)
16" (406.4mm)
8"
(203.2mm)
57" (1447.8mm)
55" (1397mm)
5" (127mm)
R 1/4"
(5mm)
3 1/2"
(90mm)
2"
(50.8mm)
R 0"
(0mm)
typ.
Parts List
KWU210-57
·Cut-Out Template
·Mounting Hardware
·Bottom Grid KBG-WSU2-57
·Bottom Grid KBG-WSU1-45
·Strainer ST-1
·Drain Cap STC-2
·Accessories Board KAB-105BB
·Cutting Board KCB-WS104BB
·Dish Rack KDR-1
·Colander KCL-2
·Serving Bowl KBW-2
·Rolling Mat KRM-11BL
Dimensions

55
Step 1. Check the Template
·Check the template against the sink for accuracy.
KRAUS Recommended Installation Type
1/2” Positive Reveal
The countertop meets the edge of the sink
fitting flush with the wall of the bowl The countertop edge sits approximately 1/2"
back from the edge of the sink
55" (1397mm)
17" (432mm)
1/2" Positive
Reveal
1/2"
Zero Reveal
1/2" Positive Reveal
Zero Reveal
1/2" Positive
Reveal
Zero Reveal
Flushed/Zero Reveal

66
Step 2. Position Template
·Check the cut-out template against the actual sink to ensure a proper sized cut-out.
·Place the cut-out template in the desired location on the countertop.
NOTE: Make sure clearance is suitable for backsplash, faucet and plumbing for the sink.
Paper Template

7
Step 3. Trace Template
·Trace template on countertop with a pencil.
Paper Template

8
Step 4. Cut Countertop
·Cut the opening in the countertop by carefully following the traced line.
NOTE: Please use the appropriate saw that best fits your countertop material.

9
Step 5. Set up Mounting Brackets
• Turn countertop over and align sink with countertop. Decide location for mounting brackets.
• Mounting holes should be 1/2" from edge of sink.
1/2"
(13mm)
Step 6. Drill Hole in Countertop
• Drill 3/8" diameter x 1/2" deep hole in the countertop.
3/8 1/2

10
Step 7. Install Anchors
• Insert anchors into drilled holes and lightly tap with a hammer until flush.
Step 8. Secure Sink to Countertop
·Use a bead of silicone (or preferred adhesive) around the rim of the sink. Check the alignment of the sink to the cutout in the
countertop. Place sink over cutout hole and press firmly.
The countertop edge sits approximately 1/2"
back from the edge of the sink
1/2"
1/2" Positive Reveal