Kraus KPF-1621 User manual

www.kraususa.com I Toll Free: 1.800.775.0703 I © 2017 Kraus USA Inc. I REV. October 25, 2017
KPF-1621
Single Lever Pull-Out Kitchen Faucet
INSTALLATION GUIDE

1
Congratulations on the purchase of your new
Kraus plumbing xture!
Please keep teh box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance, or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / customerser[email protected]
Have the model number available, and retain a copy of your receipt
with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE

2
Prior to Installation
• Make sure that cold and hot water lines are turned o
• Wrap all threaded connections with Teon tape. Always wrap in a clockwise
direction
• Cover your drain to avoid losing parts
• Do not disassemble the main faucet body, as it has been installed &
commissioned correctly & precisely before delivery from the factory
• To keep the faucet from jamming, ush the water pipe before installation
• Using condition: Working pressure at 0.05-1.0MPa (including cold & hot
water pressure) with applicable water temperature: 4C-90C
• After installation, make sure every joint is safely sealed and that there is no
leaking
• Make sure to correct the hot/cold inlet pipe correctly: if facing faucet, hot
water pipe connects on the left and cold water pipe connects on the right

3
Included Parts:
1. Faucet Body
2. Base O-Ring
3. Rubber Washer
4. Metal Washer
5. Mounting Nut
6. Mounting Screws (2)
7. Weight
8. Spray Head
9. Spray Hose
10. Hot and Cold Waterlines (2)
11. Manual
KPF-1621 Diagram and Parts List
9
8
7
2
3
4
5
6
7
11
10
1
9
8
7
2
3
4
5
6
7
11
10
1
1
10
279
10 31/32”
Minimum distance 90mm
Less than 90mm
Cold Water
32 3/32”
Ø35~Ø38
1
23
10
9
11
12 13
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
45
7
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10 11
Close
Open Left
Hot Water
Push
25˚ 90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12 13
2
3
4
5
6
7
8
1
10
279
10 31/32”
Minimum distance 90mm
Less than 90mm
Cold Water
32 3/32”
Ø35~Ø38
1
23
10
9
11
12 13
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
45
7
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10 11
Close
Open Left
Hot Water
Push
25˚ 90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12 13
2
3
4
5
6
7
8
Wrench Phillips Screwdriver
Tools you will need:

4
Dimension Drawings
249
11 9/16”
20°
231
Ø35~Ø38
Ø3/8”~Ø1 1/2”
Hot
Water
Cold
Water
475
18 3/4”
Max35
Max1 3/8”
9 3/32”
Safety Tips
• If soldering the water connections when installing the faucet, remove the O-rings,
cartridges, and washers before applying any heat
• Protect your eyes with safety glasses when cutting or soldering
mm
mm

5
249
11 9/16”
20°
231
Ø35~Ø38
Ø3/8”~Ø1 1/2”
Hot
Water
Cold
Water
475
18 3/4”
Max35
Max1 3/8”
9 3/32”
Dimension Drawings
Safety Tips
• Do not overtighten xing screws/nuts. Tighten nger-tight, then use a wrench/screwdriver
to tighten the xing screw/nut until snug
mm

6
Installation Method 1
Faucet Installation Methods
The minimum distance between the
faucet hole and the wall should be 3.5”
Minimum distance 3.5”
Less than 3.5”
30˚
Minimum distance 3.5”
Less than 3.5”
30˚
Installation Method 2
If the distance between the faucet hole
and the wall is less than 3.5”, position the
faucet lever 30 degrees to 90 degrees off
of the wall to allow for full operation

7
Step 2
Connect spray head (8) to spray hose (9) and tighten rmly. Insert the faucet body
(1) into the hole on the deck with the base o-ring (2), and then install the rubber
washer (3), metal washer (4), mounting nut (5) and mounting screws (6) from
underneath the sink
1
Ø35~Ø38
Ø1 3/8”~Ø1 1/2”
2
3
4
5
6
1
2
3
4
5
6
9
8
1
Ø35~Ø38
Ø1 3/8”~Ø1 1/2”
2
3
4
5
6
1
2
3
4
5
6
9
8
1
Ø35~Ø38
Ø1 3/8”~Ø1 1/2”
2
3
4
5
6
1
2
3
4
5
6
9
8
Step 1
Remove mounting screws (6),
mounting nut (5), metal washer
(4), and rubber washer (3) from the
faucet body (1)
Faucet Installation Steps

8
5
7
6
join
hose
Cold
Water
Hot
Water
Step 3
After adjusting the direction of
the faucet body(1), tighten the
mounting nut (5) until snug and
tighten the mounting screws (6)
to the nut with a Philips head
screwdriver
Step 4
Connect the spray hose (9) to
the supply line and tighten with
a wrench until snug, then install
the weight (7) at the lowest point
(horizontally) on the spray hose (9)
5
7
6
join
hose
Cold
Water
Hot
Water

9
Step 5
Connect hot and cold waterlines (10) to the angle stops and tighten with
a wrench until snug, then unscrew spray head (8), hold the tip of the spray
hose (9) and turn on the faucet to ush any debris
6 5/8”
5 4/5”
3/8”
(10mm)
7/8”
19.7º(22mm)
8 5/16”
1 1/4-18UNF-2A
(21mm)
10 1/8”
(257mm)
1 3/8”
(35mm)
3 3/4”
(168mm)
(147.3mm)
(96mm)
∅ 1 3/4”
(∅ 45mm)
∅ 1 15/16”
(∅ 50mm)
9/16”-18UNEF
27mm ~ 41.3mm 1 1/16” ~ 1 5/8”
∅ 1 15/16”
(∅ 50mm)
12 7/16”
(316mm)
1 5/8”
(42.5 mm Max)
7A
8B
8C
8D
8A
7A
8B
8C
8D
8A