Kraus KGUW1-30 User manual

R
INSTALLATION MANUAL
KGUW1-30 / KGUW1-33
KGUW2-30 / KGUW2-33
RipianoTM Series
Undermount Kitchen Sinks
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2020 Kraus USA Inc. I REV. October 26, 2020

2
Congratulations on the purchase of your new
Kraus plumbing fixture!
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / [email protected]
Have the model number available and retain a copy of your
receipt with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
STOP

3
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]
The step-by-step guidelines in the installation instructions are a general reference for installing a
Kraus sink. Should there be any discrepancies, Kraus cannot be held liable. It is recommended to
install all Kraus products by hiring a licensed professional.
Prior to Installation:
·Make sure that you have all necessary parts by checking the parts list. If any part is
missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a
replacement
·Inspect the sink prior to installation to make sure that it has not been damaged during
shipping
·Use the cut-out template provided by Kraus
·Observe all plumbing and building codes according to your state requirements

44
NOTE: Specialized tools may be necessary to install Kraus Granite Kitchen sinks with countertop
materials other than wood, marble or granite.
Tools you will need
Safety Goggles Silicone Adhesive Jig Saw
Phillips Screwdriver Tape Measure Pencil
Drill Hammer
Masking Tape Hole Saw
Parts List
KGUW1-30
·Cut-Out Template
·Mounting Hardware
·Strainer ST-4
·Cutting Board KCB-WS301SA
·Rolling Mat KRM-11BL
KGUW1-33
·Cut-Out Template
·Mounting Hardware
·Strainer ST-4
·Cutting Board KCB-WS301SA
·Rolling Mat KRM-11BL
KGUW2-30
·Cut-Out Template
·Mounting Hardware
·Strainer ST-4
·Cutting Board KCB-WS301SA
·Rolling Mat KRM-11BL
KGUW2-33
·Cut-Out Template
·Mounting Hardware
·Strainer ST-4
·Cutting Board KCB-WS301SA
·Rolling Mat KRM-11BL

55
Hardware (Included)
Kit for Undermount
Installation
Important
·Instructions may vary depending on countertop material. Read all instructions
carefully, and ensure that counters are compatible with sink installation before
proceeding.
·Follow the plumber’s code and builder’s code effective in your area.
·Shut off water valves prior to installation.
·Open sink packaging and verify that the sink is in perfect condition. Put sink back
into packaging to protect it until time of installation.
·To replace an existing sink, make sure that the cut-out hole in the counter is of an
adequate size to fit the new sink.

66
Dimensions
Model #: KGUW2-30
Sink Dimensions: 29” x 19” x 10”
Min Cabinet Size: 33”
Model #: KGUW2-33
Sink Dimensions: 32” x 19” x 10”
Min Cabinet Size: 36”
Model #: KGUW1-30
Sink Dimensions: 29” x 19” x 10”
Min Cabinet Size: 33”
Model #: KGUW1-33
Sink Dimensions: 32” x 19” x 10”
Min Cabinet Size: 36”
30" (762mm)
32" (812.8mm)
16" (407mm) 19" (482mm)
1" (25.4mm) 1" (25.4mm)
1"
(25.4mm)
R5/8"
(15mm)
6 3/8"
(160.5mm)
5 7/8"
(148.9mm)
10"
(254.78mm)
9 3/8"
(239mm)
3/8"
(8mm)
1/2"
(13mm)
28 5/8" (726mm)
R1"
(24mm)
3 5/8"
(93.7mm)
17" (431mm)
30" (762mm)
32" (812.8mm)
16" (407mm) 19" (482mm)
1" (25.4mm) 1" (25.4mm)
1"
(25.4mm)
R5/8"
(15mm)
6 3/8"
(160.5mm)
5 7/8"
(148.9mm)
10"
(254.78mm)
9 3/8"
(239mm)
3/8"
(8mm)
1/2"
(13mm)
28 5/8" (726mm)
R1"
(24mm)
3 5/8"
(93.7mm)
17" (431mm)
27" (686mm)
29" (737mm)
16" (407mm) 19" (482mm)
1" (25.4mm) 1" (25.4mm)
1"
(25.4mm)
R5/8"
(15mm)
6 3/8"
(160.5mm)
5"
(125.5mm)
10"
(254.78mm)
9 3/8"
(239mm)
3/8"
(8mm)
1/2"
(13mm)
25 5/8" (649.8mm)
R1"
(24mm)
3 5/8"
(93.7mm)
17" (431mm)
27" (686mm)
29" (737mm)
16" (407mm) 19" (482mm)
1" (25.4mm) 1" (25.4mm)
1"
(25.4mm)
R5/8"
(15mm)
6 3/8"
(160.5mm)
5"
(125.5mm)
10"
(254.78mm)
9 3/8"
(239mm)
3/8"
(8mm)
1/2"
(13mm)
25 5/8" (649.8mm)
R1"
(24mm)
3 5/8"
(93.7mm)
17" (431mm)

7
3/8” POSITIVE
FLUSHED/ZERO
Centerline
Step 1. Determine Reveal Type
·Use scissors to cut along the line of the paper template for your desired reveal type
(Negative, Positive, or Flushed Reveal)
KRAUS Recommended Installation Type
3/8” Positive Reveal
Flushed/Zero Reveal

8
Step 2. Position Template
·Check the cut-out template against the actual sink to ensure a proper sized cut-out.
·Place the cut-out template in the desired location on the countertop.
NOTE: Make sure clearance is suitable for backsplash, faucet and plumbing for the sink.
Paper Template

9
Step 3. Trace Template
·Trace template on countertop with a pencil.
Paper Template

10
Step 4. Cut Countertop
·Cut the opening in the countertop by carefully following the traced line.
NOTE: Please use the appropriate saw that best fits your countertop material.