KREAFUNK aGlow User manual

aGLOW
Operation manual
Bedienungshandbuch
Manual de instrucciones
Manuel d’utilisation
Brugermanual
Portable Bluetooth Speaker Box

2

3
English 4
Deutsch 20
Español 36
Français 52
Dansk 68
This product is in compliance with the essential requirements and other relevant
provisions of Directive 2014/53/EU. The declaration of conformity may be consulted at:
www.kreafunk.com/declaration-of-conformity/aglow

4English
English
Operation manual

5
English
SAFETY AND MAINTENANCE INSTRUCTIONS
1. Please read this operation manual carefully before use.
2. The safety and maintenance instructions in this operation manual
should be retained for future reference and must be followed at all
times.
3. Keep the product away from heat sources such as radiators, heaters or
other appliances that produce heat.
4. Do not expose the product to direct sunlight for longer periods. High
temperatures will shorten the life of the product, destroy the battery and
distort certain plastic parts.
5. Do not expose the product to extreme cold as it may damage the
internal circuit board.
6. Avoid liquids getting into the product.
7. Do not throw with or stamp on the product. This may damage the
internal circuit board.
8. Do not try to disassemble the product. This must only be done by a
professional.
9. Do not use concentrated chemical products or detergent to clean the
product.
10. Keep the surface away from sharp things, as these may cause damage
to the plastic parts.
11. Use 5V / 1A power supplies only. The connection of power supplies with
higher voltage may lead to severe damage.
12.Donotarbitrarilydiscardorplacethelithiumbatterynearreorintense
heat in order to avoid a risk of explosion.

6English
If you do experience any problems
with your product please contact
the retailer you purchased the
product from. The retailer will
provide you with guidance and if
that does not solve the problem
the retailer will handle the claim
directly with KREAFUNK.
TURNING YOUR aGLOW
ON / OFF
1. Press and hold the power
button for 1-2 seconds
to turn on aGLOW. The lamp
will give a brief white gleam,
andtheLEDringwillbriey
stay solid blue, and a prompt
sound will play – indicating that
aGLOW is turned on.
2. Press and hold the power
button for 1-2 seconds to
turnoaGLOW.TheLEDring
willbrieystaysolidred,and
a prompt sound will play –
indicating that aGLOW is turned
o.
PAIRING YOUR aGLOW TO
A DEVICE
1. After turning on aGLOW the
LEDringstartsashingblue.
This means aGLOW is in
Bluetooth pairing mode, and it
willcontinueashingblueuntil
paired to a Bluetooth playback
device.
2. Enable your smartphone’s
or another playback device’s
Bluetooth function and search
for Bluetooth devices.
3. Select ‘aGLOW’ from the list
of found Bluetooth devices.
When aGLOW is successfully
connected you will hear a
prompt sound and the LED ring
willturno.
From now on, every time you turn
on aGLOW and your Bluetooth
device simultaneously, they will
automatically connect.

7
English
PAIRING TO ANOTHER
DEVICE (PAIRING MODE)
To enter pairing mode to pair with
another device than the active one,
press and hold the pairing button
for 2 seconds until the LED
ringstartsashingblueandred.
aGLOW will play a short prompt
sound. It is now ready to pair with
any other Bluetooth devices.
If aGLOW is disconnected from
all previous devices, it will
automatically enter pairing mode
andtheLEDringstartsashing
blue and red alternately.
PAIRING TWO aGLOWs
FOR TRUE WIRELESS
STEREO (TWS)
1. Turn on the two aGLOW
speakers, and make sure
they are not connected to any
Bluetooth playback devices.
If one or both aGLOW are
connected to a device, please
disconnect them.
2. Brieypressthepairingbutton
on one aGLOW to activate
TWS mode. The LED ring will
ashcyan,whileplayinga
short prompt sound. Now, this
aGLOW functions as the ‘master
speaker’ and will search for the
other aGLOW. When the other
aGLOW is connected, you will
hear one more prompt sound.
3. When the two aGLOWs are
paired, the ‘master speaker’
will automatically change into
regular Bluetooth pairing mode.
Now, you can pair it with your
Bluetooth playback device and
enjoy True Wireless Stereo.
The ‘master speaker’ will play left
channel, while the other aGLOW
will play right channel.
4. To disconnect two TWS
paired speakers and reset
TWS pairing, press and hold
the pairing button for 2
seconds.

8English
BUTTON FUNCTIONS
Multi-function button
• Press button to PLAY or
PAUSE music
• Press and hold button for 1-2
seconds to turn ON / OFF
• If there is an incoming call,
press the button to ACCEPT
CALL
• Press the button again to END
CALL.
Button
• Press button to INCREASE
VOLUME
• Press and hold button to go to
NEXT TRACK
Button
• Press button to DECREASE
VOLUME
• Press and hold button to go to
PREVIOUS TRACK
Pairing button
• Press and hold button to
activate BLUETOOTH PAIRING
MODE
• Press button to activate TWS
PAIRING MODE
• Press and hold to clear TWS
pairing

9
English
Lamp control Button
You can activate the lamp function
without having to turn on the
speaker.
• Press once to turn on the
Lamp
• Press again to toggle
between COLOURS and LIGHT
OFF (White, Red, Green, Blue,
OFF)
• Press and hold the lamp
control button to fade
between dim and bright light
aGLOW APP
INSTRUCTIONS
QUICK SETUP
• Search for “aGLOW-
KREAFUNK” in App Store
(iOS) or Google Play Store
(Android). You can also scan
the QR code located on the
last page of the user manual.
• Make sure your device is
connected with aGLOW via
Bluetooth.
• Download and open the
‘aGLOW-KREAFUNK’ app on
your device and enter the
start page.

10 English
CONNECTING aGLOW TO
THE ‘aGLOW’ APP
Slide the panel up from the bottom
of the screen to choose and
connect your aGLOW speaker to
the app.

11
English
• Once aGLOW is connected, go
back to the start page.

12 English
SETTING AN ALARM
(WITH SOUND & WAKE-
UP LIGHT)
• Choose the ‘Alarm’ button on
the start page

13
English
• Press ’Set alarm clocks’ in
the bottom of the screen to
add a new alarm
• Now you can set the time for
the alarm and choose, which
days of the week to repeat

14 English
Youcansetuptofourdierent
alarms, and it is possible to enable
and disable both ‘sound’ and ‘wake-
up light’ by sliding the respective
buttons.
WAKE-UP LIGHT
By activating the ‘Wake-up light’
you will be awakened by gradually
increasing light as the alarm goes
o.
SOUND
If you choose ‘Sound’ you will be
awakened by an alarm sound as
thealarmgoeso.
Press the Multi-function button
toturnothealarmorlightafter
itgoeso.
• Press ‘Save’ to save the
alarm.

15
English
You can delete an alarm by sliding
left on the alarm overview.
USING aGLOW AS A LAMP
Choose the ‘Light’ button on
the start page, to go to the light
settings.

16 English
Light icons
In ‘Breath’ mode, the light will fade
between dim and bright repeatedly
In ‘Rhythm’ mode the light will
change to the beat of the music
playing from your smartphone,
tablet or similar device
Clickorslidetondyourfavorite
colours from the colour wheel
Slide to change the brightness on
aGLOW.
Click to choose between the
standard colours
Turnlighton/o
CHARGING
If the battery power is below 15%,
the LED ring will turn solid red.
Below 10%, the LED ring starts
ashingred,whichmeansthatthe
battery is extremely low.
To maintain a long battery life, it
is recommended that you charge
aGLOW, when the LED ring turns
red.

17
English
Below are two ways to charge
aGLOW:
1. First option: When aGLOW is
low on power, connect it to a
USB power source, with the
included USB to micro USB
cable.Thelampwillashwhite
twice to indicate charging has
begun
2. Second option: aGLOW supports
wireless charging meaning
it is compatible with a Qi
charger. Turn on your wireless
Qi charger and place aGLOW
ontop.aGLOWwillashwhite
twice to indicate charging has
begun
The LED ring turns red, orange or
greentoshowdierentcharging
statuses:
• red = power is below 15%
• orange = power between 15%
and 100%
• green = fully charged, you can
disconnect charging

18 English
SPECIFICATIONS
Bluetooth 4.2
Built-in microphone
IP65 water resistant
Speaker Output: 2 x 5W
SNR: 75 dB
THD+N: <10%
Battery: 4400mAh lithium
USB & Wireless charging input:
5V / 1A
Weight: 630g
Size: 183.5 x 105 mm
APP controls Colorful LED lights
and Alarm clock function

19
English

20 Deutsch
Deutsch
Bedienungshandbuch