KREAFUNK Asound User manual

Portable Bluetooth
speaker box
Manual

English��������������� page 4
Dansk����������������� page 14
Deutsch ������������� page 24
Français������������� page 36
Español�������������� page 48

4
English
1� Buttons
Power
Bluetooth
Previous
Play / Pause / Handfree
Next
Volume –
Volume +

5
English
2� Charge aSound
1.Connect aSound with AC adapter
directly (included).
2.Red LED turns ON during charging,
turns OFF when fully charged.
3.Unplug AC adaptor when fully
charged.
Note:
The Red LED will ash and make a
sound when the battery power is low
(<21%).
3� Starting aSound
Bluetooth Speaker
1. When fully charged, hold down the
POWER button to turn on the speaker.

6
English
2. aSound is on standby mode after
power-on if the blue LED blinks quickly.
3. aSound will turn off for power saving
if it is not in use in 10 minutes.
4. Press any button located on the top
to activate aSound from standby mode.
5. To manually turn off aSound
Speaker, hold down the POWER button.
4� Pairing with Bluetooth
enabled devices
(Mobile phones/Tablets etc.)
1. Keep the speaker and device within
1 meter of each other.
2. Hold down the power button for 2
seconds to turn on the speaker, the
LED indicator will blink quickly in blue

7
English
while the speaker enters search mode.
3. Start the Bluetooth function on your
mobile device and look for “aSound”
in the Bluetooth device list (depending
on the Bluetooth version of your device
you may have to enter the pass code
‘0000’).
4. After successfully connecting, the
LED will change to solid blue.
Note:
- If the pairing was not successful, turn
off the speaker and re-pair again.
- After successful pairing, paired
devices will remember each other so
there is no need to pair again unless
pairing information is deleted.
- To pair with a new device, just follow
steps 1-4 above after un-pairing the
existing device.

8
English
5� Re-connecting to a paired
device
If the speaker does not connect to the
last used device automatically, then
you will need to select it manually
from the list of devices on your mobile
device.
6� Pair aSound with a
different device
First disconnect with existing device by
either holding down the BLUETOOTH
button or switching off the Bluetooth
connection for the existing device, and
then pair with other device according to
steps 1-4 above.

9
English
7� Hands-free phone calls
Make sure mobile phone is paired with
speaker.
1. Press the “Bluetooth/Hands-free”
button to answer an incoming phone
call.
2. Press again to end a call.
3. Use the volume buttons to change
the volume of the call.
8� Play / Pause
1. When the speaker is playing music,
press the Play /Pause/ Handfree quickly
to pause.
2. Press again to continue play.

10
English
9� Next / Previous
1. Press NEXT to go to next track.
2. Press Previous to go to previous track.
10� Volume control
1. Control volume via the Bluetooth
device itself.
2. Control volume via the volume +/-
buttons located on top of Speaker.
11� Connecting external
devices (AUX port)
You can connect any music device to
the aSound speaker via the AUX port
using the cable included. The speaker
will not use the Bluetooth function while
connected via this cable.

11
English
12� 1-Pair-2 function
(Stereo option)
When you buy 2 aSound, then you can
enjoy the stereo sound by connecting
2 together..
Note:
Please ensure to pair 2 aSound rstly,
then to pair the master one with your BT
device to enjoy the music.
1. Turn on 2 aSound speakers and
make sure both are under BLUETOOTH
mode.
2. Press and hold the “BLUETOOTH +
PREVIOUS” button at the same time on
both units until you hear a “du ~ du ~”
sound from both. The devices will then
start to search for one another.

12
English
3. When “du ~ du ~” sound is heard
from both speakers, and LED light
changes to constant (not ashing), the
two speakers are connected.
4. Now, Press the “BLUETOOTH”
button of either one of them to be the
master one, until the LED indicator of
“BLUETOOTH” button blinks quickly
(another one is the secondary one
automatically with LED indicator solid).
5. While the LED indicator of master
one blinks, it’s ready to be research by
other device.
6. Start the Bluetooth function on
your mobile device and look for
“KREAFUNK” in the Bluetooth device
list (depending on the Bluetooth version
of your device you may have to enter
pass code ‘0000’).

13
English
7. After successfully connected, the
LED will change to solid Warm-White.
8. Now you can start to enjoy the
STEREO Hi-Fi sound with 2 aSound.
Note:
The master one can control the
volume-/+ & track previous/next
function for both at the same time,
but the secondary only can adjust the
volume-/+.

14
Dansk
1� Knapper
Power
Bluetooth
Forrige
Afspil/Pause/Håndfri
Næste
Volume –
Volume +

15
Dansk
2� Oplad aSound
1.Forbind aSound direkte med AC-
adapter (inkluderet).
2.Rød LED tændes under opladning,
slukker når den er fuldt opladet.
3.Frakobbel AC-adapter, når aSound
er fuldt opladet.
Bemærk: Den røde LED blinker og laver
en lyd, når batteriet er lavt (<21%).
3� Start aSound Bluetooth
højttaler
1. Når højtaleren er fuldt opladet, skal
du holde POWER-knappen nede for at
tænde for højttaleren.
2. aSound er på standby efter power-
on, hvis det blå LED-lys blinker hurtigt.
Power
Bluetooth
Forrige
Afspil/Pause/Håndfri
Næste
Volume –
Volume +

16
Dansk
3. aSound slukker for at spare strøm,
hvis den ikke er i brug i 10 minutter.
4. Tryk på en knap placeret på toppen
for at aktivere aSound fra standby.
5. For at slukke aSound højtaleren
manuelt, hold knappen POWER nede.
4� Parring med Bluetooth-
enheder
(Mobiltelefoner / Tabletter etc.)
1. Hold højttaleren og enheden inden
for 1 meters afstand af hinanden.
2. Hold POWER-knappen nede i 2
sekunder for at tænde for højttaleren,
den blå LED-indikator blinker hurtigt,
når højttaleren går i søgetilstand.
3. Start Bluetooth-funktionen på din

17
Dansk
mobile enhed, og led efter “aSound”
i enhedens liste af mulige Bluetooth-
forbindelser (afhængigt af Bluetooth-
version på din enhed vil du måske blive
nødt til at indtaste adgangskoden “0000”).
4 Efter en vellykket tilslutning, vil LED-
lyset skifte til at være konstant blåt.
Bemærk:
- Hvis parringen ikke lykkedes, skal du
slukke for højttaleren og prøve at parre
igen.
- Efter en vellykket parring, vil parrede
enheder huske hinanden. Der er derfor
ingen grund til at oprette forbindelse
igen, medmindre parringsinformation
slettes.
- Hvis du vil oprette en forbindelse til
en ny enhed, skal du blot følge trin
1-4 ovenfor efter at have frakoblet den
eksisterende enhed.

18
Dansk
5� Gentilslutning til en
forbundet enhed
Hvis højttaleren ikke opretter
forbindelse til den sidst anvendte
enhed automatisk, er du nødt til at
vælge den manuelt fra listen over
enheder på din mobile enhed.
6� Par aSound med en
anden enhed
Afbryd først forbindelsen til den
eksisterende enhed ved enten at holde
BLUETOOTH-knappen nede eller
slukke for Bluetooth-forbindelsen til
den eksisterende enhed manuelt. Par
herefter med en anden enhed i henhold
til trin 1-4 ovenfor.

19
Dansk
7� Håndfri telefonopkald,
Sørg for mobiltelefon er parret med
højttaler.
1. Tryk på “Bluetooth / Håndfri”
knappen for at besvare et indgående
opkald.
2. Tryk igen for at afslutte et opkald.
3. Brug lydstyrkeknapperne til at ændre
lydstyrken for opkaldet.
8� Afspil / Pause
1. Når højttaleren afspiller musik, skal
du trykke på afspil / pause / håndfri
hurtigt for at holde pause.
2. Tryk igen for at fortsætte med at
afspille.

20
Dansk
9� Næste / Forrige
1. Tryk på næste for at gå til næste
nummer.
2. Tryk på forrige for at gå til forrige
nummer.
10� Lydstyrkekontrol
1. Kontroller lydstyrken via Bluetooth-
enheden selv.
2. Kontroller lydstyrken via lydstyrke
+/- knapperne placeret på toppen af
højttaleren.
11� Tilslutning af eksterne
enheder (AUX-port)
Du kan tilslutte enhver musik-enhed
til aSound højttaler via AUX-porten