KSB Calio S Installation instructions

High-efficiency Circulator / Drinking Water
Pump
Calio S / Calio-Therm S
Installation/Operating Manual

Legal information/Copyright
Installation/Operating Manual Calio S / Calio-Therm S
Original operating manual
All rights reserved. The contents provided herein must neither be distributed, copied, reproduced,
edited or processed for any other purpose, nor otherwise transmitted, published or made available to a
third party without the manufacturer's express written consent.
Subject to technical modification without prior notice.
© KSB SE & Co. KGaA, Frankenthal 10/12/2018

Contents
3 of 44
Calio S / Calio-Therm S
Contents
Glossary .................................................................................................................................................. 5
1 General.................................................................................................................................................... 6
1.1 Principles ...........................................................................................................................................................6
1.2 Target group.....................................................................................................................................................6
1.3 Symbols .............................................................................................................................................................6
1.4 Key to safety symbols/markings.......................................................................................................................7
2 Safety...................................................................................................................................................... 8
2.1 General..............................................................................................................................................................8
2.2 Intended use .....................................................................................................................................................8
2.2.1 Prevention of foreseeable misuse.......................................................................................................8
2.3 Personnel qualification and training...............................................................................................................8
2.4 Consequences and risks caused by non-compliance with this manual .........................................................9
2.5 Safety awareness ..............................................................................................................................................9
2.6 Safety information for the user/operator.......................................................................................................9
2.7 Safety information for maintenance, inspection and installation ................................................................9
2.8 Unauthorised modes of operation................................................................................................................10
3 Transport/Temporary Storage/Disposal............................................................................................. 11
3.1 Checking the condition upon delivery..........................................................................................................11
3.2 Transport.........................................................................................................................................................11
3.3 Storage/preservation......................................................................................................................................11
3.4 Return to supplier...........................................................................................................................................12
3.5 Disposal ...........................................................................................................................................................12
4 Description of the Pump (Set)............................................................................................................. 13
4.1 General description ........................................................................................................................................13
4.2 Designation.....................................................................................................................................................13
4.3 Name plate......................................................................................................................................................13
4.4 Design details..................................................................................................................................................14
4.5 Configuration and function...........................................................................................................................15
4.6 Noise characteristics .......................................................................................................................................15
4.7 Dimensions and weight..................................................................................................................................16
4.8 Scope of supply...............................................................................................................................................16
4.9 Accessories ......................................................................................................................................................16
5 Installation at Site................................................................................................................................ 17
5.1 Safety regulations...........................................................................................................................................17
5.2 Checks to be carried out prior to installation...............................................................................................17
5.3 Installing the pump set ..................................................................................................................................17
5.4 Connecting the piping ...................................................................................................................................19
5.5 Enclosure/insulation .......................................................................................................................................19
5.6 Electrical connection ......................................................................................................................................20
5.6.1 Connecting the power cable .............................................................................................................20
6 Commissioning/Start-up/Shutdown................................................................................................... 22
6.1 Commissioning/Start-up.................................................................................................................................22
6.1.1 Prerequisites for commissioning/start-up .........................................................................................22
6.1.2 Priming and venting the pump.........................................................................................................22
6.1.3 Start-up...............................................................................................................................................23
6.2 Operating limits..............................................................................................................................................23
6.2.1 Ambient temperature........................................................................................................................24
6.2.2 Minimum inlet pressure.....................................................................................................................24
6.2.3 Maximum operating pressure ...........................................................................................................24
6.2.4 Fluid handled .....................................................................................................................................25
6.3 Shutdown........................................................................................................................................................27

Contents
4 of 44 Calio S / Calio-Therm S
6.3.1 Measures to be taken for shutdown ................................................................................................27
6.3.2 Shutdown ...........................................................................................................................................27
6.4 Returning to service .......................................................................................................................................27
7 Operation.............................................................................................................................................. 28
7.1 Control panel..................................................................................................................................................28
7.1.1 Display ................................................................................................................................................28
7.2 Mode of operation.........................................................................................................................................29
7.2.1 Information on settings.....................................................................................................................29
7.2.2 Constant-pressure control .................................................................................................................30
7.2.3 Proportional-pressure control ...........................................................................................................31
7.2.4 Open-loop control .............................................................................................................................32
7.3 Functions.........................................................................................................................................................33
7.3.1 Setback operation..............................................................................................................................33
7.3.2 Protective functions ...........................................................................................................................35
7.3.3 Saving data.........................................................................................................................................35
7.3.4 Fault messages ...................................................................................................................................35
8 Servicing/Maintenance........................................................................................................................ 36
8.1 Servicing/maintenance/inspection.................................................................................................................36
8.2 Drainage/cleaning ..........................................................................................................................................37
8.3 Removing the pump set from the piping .....................................................................................................37
8.3.1 Removing the power cable ...............................................................................................................38
9 Trouble-shooting.................................................................................................................................. 39
10 Related Documents.............................................................................................................................. 40
10.1 Sectional drawing with list of components ..................................................................................................40
11 EU Declaration of Conformity............................................................................................................. 41
Index ..................................................................................................................................................... 42

Glossary
5 of 44
Calio S / Calio-Therm S
Glossary
Discharge line
The pipeline which is connected to the discharge
nozzle
Pump
Machine without drive, additional components or
accessories
Pump set
Complete pump set consisting of pump, drive,
additional components and accessories
Setback operation
Setback Operation avoids running the pump set at
an unchanged control curve during the night. It
lowers the mass flow rate, noise level and power
consumption.
Suction lift line/suction head line
The pipeline which is connected to the suction
nozzle

1 General
6 of 44 Calio S / Calio-Therm S
1 General
1.1 Principles
This instruction manual is valid for the type series and variants indicated on the front
cover.
The manual describes the proper and safe use of this equipment in all phases of
operation.
The name plate indicates the type series and size as well as the main operating data.
They uniquely identify the pump (set) and serve as identification for all further
business processes.
In the event of damage, immediately contact your nearest KSB Service centre to
maintain the right to claim under warranty.
1.2 Target group
This operating manual is aimed at the target group of trained and qualified specialist
technical personnel. (ðSection2.3,Page8)
1.3 Symbols
Table1: Symbols used in this manual
Symbol Description
✓Conditions which need to be fulfilled before proceeding with the
step-by-step instructions
⊳Safety instructions
⇨Result of an action
⇨Cross-references
1.
2.
Step-by-step instructions
Note
Recommendations and important information on how to handle
the product

1 General
7 of 44
Calio S / Calio-Therm S
1.4 Key to safety symbols/markings
Table2: Definition of safety symbols/markings
Symbol Description
!DANGER
DANGER
This signal word indicates a high-risk hazard which, if not avoided,
will result in death or serious injury.
!WARNING
WARNING
This signal word indicates a medium-risk hazard which, if not
avoided, could result in death or serious injury.
CAUTION
CAUTION
This signal word indicates a hazard which, if not avoided, could
result in damage to the machine and its functions.
General hazard
In conjunction with one of the signal words this symbol indicates a
hazard which will or could result in death or serious injury.
Electrical hazard
In conjunction with one of the signal words this symbol indicates a
hazard involving electrical voltage and identifies information about
protection against electrical voltage.
Machine damage
In conjunction with the signal word CAUTION this symbol indicates
a hazard for the machine and its functions.
Warning: Strong magnetic field
In conjunction with one of the signal words this symbol indicates a
hazard involving magnetic fields and identifies information about
protection against magnetic fields.
Warning for persons with pacemaker
In conjunction with one of the signal words this symbol indicates a
hazard involving magnetic fields and identifies special information
for persons with a pacemaker.
Warning about hot surfaces
In conjunction with one of the signal words this symbol indicates a
hazard involving hot surfaces.

2 Safety
8 of 44 Calio S / Calio-Therm S
2 Safety
!DANGER
All the information contained in this section refers to hazardous situations.
In addition to the present general safety information the action-related safety
information given in the other sections must be observed.
2.1 General
▪The operator is responsible for ensuring compliance with all local regulations not
taken into account.
▪This operating manual contains general installation, operating and maintenance
instructions that must be observed to ensure safe operation of the system and
prevent personal injury and damage to property.
▪Comply with all the safety instructions given in the individual sections of this
operating manual.
▪The operating manual must be read and understood by the responsible specialist
personnel/operators prior to installation and commissioning.
▪The contents of this operating manual must be available to the specialist
personnel at the site at all times.
▪Information and markings attached directly to the product must always be
complied with and kept in a perfectly legible condition at all times. This applies
to, for example:
▪Flow direction arrow
▪Markings for connections
▪Name plate
▪Warnings
2.2 Intended use
▪The pump (set) must only be operated in the fields of application and within the
use limits specified in the other applicable documents.
▪Only operate pumps/pump sets which are in perfect technical condition.
▪Do not operate the pump (set) in partially assembled condition.
▪Only use the pump to handle the fluids described in the data sheet or product
literature of the pump model or variant.
▪Never operate the pump without the fluid to be handled.
▪Observe the minimum flow rate and maximum flow rate indicated in the data
sheet or product literature (e.g. to prevent overheating, cavitation damage,
bearing damage).
▪Do not throttle the flow rate on the suction side of the pump (to prevent
cavitation damage).
▪Consult the manufacturer about any use or mode of operation not described in
the data sheet or product literature.
2.2.1 Prevention of foreseeable misuse
▪Observe all safety information and instructions in this manual.
▪Never exceed the permissible application and operating limits specified in the
data sheet or product literature regarding pressure, temperature, etc.
2.3 Personnel qualification and training
All personnel involved must be fully qualified to transport, install, operate, maintain
and inspect the equipment this manual refers to.
The responsibilities, competence and supervision of all personnel involved in
transport, installation, operation, maintenance and inspection must be clearly
defined by the operator.

2 Safety
9 of 44
Calio S / Calio-Therm S
Deficits in knowledge must be rectified by means of training and instruction
provided by sufficiently trained specialist personnel. If required, the operator can
commission the manufacturer/supplier to train the personnel.
Training on the pump (set) must always be supervised by technical specialist
personnel.
This device may be operated by children from the age of 8 as well as by persons of
limited physical, sensory or mental abilities or lacking experience and knowledge,
provided that they are supervised, they have been instructed on how to use this
device safely and they understand the hazards it presents. It is impermissible for
children to play with this device. Children must not clean the device or perform any
service work to be carried out by the operator at the device without supervision.
2.4 Consequences and risks caused by non-compliance with this manual
▪Non-compliance with these operating instructions will lead to forfeiture of
warranty cover and of any and all rights to claims for damages.
▪Non-compliance can, for example, have the following consequences:
– Hazards to persons due to electrical, thermal, mechanical and chemical
effects and explosions
– Failure of important product functions
– Failure of prescribed maintenance and servicing practices
– Hazard to the environment due to leakage of hazardous substances
2.5 Safety awareness
In addition to the safety information contained in this operating manual and the
intended use, the following safety regulations shall be complied with:
▪Accident prevention, health regulations and safety regulations
▪Explosion protection regulations
▪Safety regulations for handling hazardous substances
▪Applicable standards, directives and laws
2.6 Safety information for the user/operator
▪Fit protective equipment (e.g. contact guards) supplied by the operator for hot,
cold or moving parts, and check that the equipment functions properly.
▪Do not remove any protective equipment (e.g. contact guards) during operation.
▪Provide the personnel with protective equipment and make sure it is used.
▪Contain leakages (e.g. at the shaft seal) of hazardous fluids handled (e.g.
explosive, toxic, hot) so as to avoid any danger to persons and the environment.
Adhere to all relevant laws.
▪Eliminate all electrical hazards. (In this respect refer to the applicable national
safety regulations and/or regulations issued by the local energy supply
companies.)
▪If shutting down the pump does not increase potential risk, fit an emergency-
stop control device in the immediate vicinity of the pump (set) during pump set
installation.
2.7 Safety information for maintenance, inspection and installation
▪Modifications or alterations of the pump (set) are only permitted with the
manufacturer's prior consent.
▪Use only original spare parts or parts/components authorised by the
manufacturer. The use of other parts/components can invalidate any liability of
the manufacturer for resulting damage.
▪The operator ensures that maintenance, inspection and installation are
performed by authorised, qualified specialist personnel who are thoroughly
familiar with the manual.

2 Safety
10 of 44 Calio S / Calio-Therm S
▪Only carry out work on the pump (set) during standstill of the pump.
▪Only perform work on the pump set when it has been disconnected from the
power supply (de-energised).
▪The pump (set) must have cooled down to ambient temperature.
▪Pump pressure must have been released and the pump must have been drained.
▪When taking the pump set out of service always adhere to the procedure
described in the manual. (ðSection6.3.1,Page27)
▪Decontaminate pumps which handle fluids posing a health hazard.
▪As soon as the work has been completed, re-install and re-activate any safety-
relevant devices and protective devices. Before returning the product to service,
observe all instructions on commissioning. (ðSection6.1,Page22)
2.8 Unauthorised modes of operation
Never operate the pump (set) outside the limits stated in the data sheet and in this
manual.
The warranty relating to the operating reliability and safety of the supplied pump
(set) is only valid if the equipment is used in accordance with its intended use.

3 Transport/Temporary Storage/Disposal
11 of 44
Calio S / Calio-Therm S
3 Transport/Temporary Storage/Disposal
3.1 Checking the condition upon delivery
1. On transfer of goods, check each packaging unit for damage.
2. In the event of in-transit damage, assess the exact damage, document it and
notify KSB or the supplying dealer and the insurer about the damage in writing
immediately.
3.2 Transport
CAUTION
Improper pump transport
Damage to the pump!
▷Never suspend the pump/pump set from the power cable.
▷Prevent the pump (set) from getting knocked or dropped.
3.3 Storage/preservation
CAUTION
Damage during storage due to humidity, dirt or vermin
Corrosion/contamination of the pump (set)!
▷For outdoor storage cover the pump (set) or the packaged pump (set) and
accessories with waterproof material.
CAUTION
Wet, contaminated or damaged openings and connections
Leakage or damage to the pump!
▷Clean and cover pump openings and connections as required prior to putting
the pump into storage.
If commissioning is to take place some time after delivery, we recommend that the
following measures be taken for pump (set) storage.
Store the pump (set) in a dry, protected room where the atmospheric humidity is as
constant as possible.
If properly stored indoors, the equipment is protected for a maximum of 12months.
New pumps/pump sets are supplied by our factory duly prepared for storage.
For storing a pump (set) which has already been operated, observe the instructions
in (ðSection6.3.1,Page27) .
Table3: Ambient conditions for storage
Ambient condition Value
Relative humidity 80% maximum
Ambient temperature 0°C to + 40°C
▪Well-ventilated
▪Dry
▪Dust-free
▪Shock-free
▪Vibration-free

3 Transport/Temporary Storage/Disposal
12 of 44 Calio S / Calio-Therm S
3.4 Return to supplier
1. Prior to returning the product to the supplier, flush and clean it, particularly if it
has been used in noxious, explosive, hot or other hazardous fluids.
2. If the product has been used in fluids whose residues could lead to corrosion
damage in the presence of atmospheric humidity or could ignite upon contact
with oxygen, the product must also be neutralised and treated with anhydrous
inert gas to ensure drying.
3. Always complete and enclose a certificate of decontamination when returning
the product.
Indicate any safety measures and decontamination measures taken.
NOTE
If required, a blank certificate of decontamination can be downloaded from the
following web site: www.ksb.com/certificate_of_decontamination
3.5 Disposal
DANGER
Strong magnetic field in the rotor area
Danger of death for persons with pacemaker!
Interference with magnetic data carriers, electronic devices, components and
instruments!
Uncontrolled magnetic attraction forces between magnet-equipped components,
tools or similar!
▷Keep a safety distance of at least 0.3m.
WARNING
Fluids handled, consumables and supplies which are hot and/or pose a health
hazard
Hazard to persons and the environment!
▷Collect and properly dispose of flushing fluid and any fluid residues.
▷Wear safety clothing and a protective mask if required.
▷Observe all legal regulations on the disposal of fluids posing a health hazard.
1. Dismantle the pump (set).
Collect greases and other lubricants during dismantling.
2. Separate and sort the pump materials, e.g. by:
- Metals
- Plastics
- Electronic waste
- Greases and other lubricants
3. Dispose of materials in accordance with local regulations or in another
controlled manner.
Electrical or electronic equipment marked with the adjacent symbol must not be
disposed of in household waste at the end of its service life.
Contact your local waste disposal partner for returns.
If the used electrical or electronic equipment contains personal data, the user is
responsible for deleting it before the equipment is returned.

4 Description of the Pump (Set)
13 of 44
Calio S / Calio-Therm S
4 Description of the Pump (Set)
4.1 General description
▪High-efficiency circulator pumps with continuously variable speed control
▪Non-self-priming in-line pump with integrated permanent magnet motor and
electronic variable speed system
Pump for handling clean, non-aggressive fluids which are not chemically and
mechanically aggressive to the pump materials.
4.2 Designation
Example: Calio S 25-40-130
Table4: Designation key
Code Description
Calio S Type series
Calio S High-efficiency circulator pump
Calio-ThermS High-efficiency circulator pump for drinking water
applications/ foodstuff applications
25 Connection
15 Rp 1/2
25 Rp 1
30 Rp 1 1/4
40 Head H [m]
40 Head × 10
Example: 4 m × 10 = 40
130 Overall length
130 130mm
-1) See dimensions.
4.3 Name plate
S/Nr: 29134992-201817-12345
Calio S 25-60
1~ 230 V - 50/60 Hz
0,06 - 0,46 A
Class F IP 42
EEI ≤ 0,20
1
2
3
4
5
PN 6/10
Made in Turkey | KSB SE & Co. KGaA Johann-Klein-Str. 9 67227 Frankenthal (Germany)
6
TF 95
6 - 25 W
7
8
9
10
11
Fig.1: Name plate (example)
1 Type series, size 7 Current input
2 Mains voltage, frequency 8 Pressure class
3 Thermal class 9 Temperature class
4 Enclosure 10 Energy efficiency index EEI
5 Electrical power 11 QR code
6 Production number
1) Blank

4 Description of the Pump (Set)
14 of 44 Calio S / Calio-Therm S
Key to the production
number
Example: 29134992-201817-12345
Table5: Key to the production number
Code Description
29134992 Material number
2018 Year of production
17 Week of production
12345 Consecutive number
4.4 Design details
Design
▪Maintenance-free high-efficiency wet rotor pump (glandless)
Drive
▪High-efficiency permanent magnet synchronous motor, brushless, self-cooling,
with continuously variable differential pressure control
▪1~230VAC +/- 10%
▪Frequency 50Hz/60Hz
▪IP42 enclosure
▪Thermal class F
▪Temperature class TF95
▪Interference emissions EN55014-1
▪Interference immunity EN 55014-2
▪Interference immunity EN60335-2-51
Bearings
▪Ceramic bearings
Connections
▪Screw-ended
Operating modes
▪Automatic mode with constant-pressure control or proportional-pressure control
▪Fixed speed operation with three speed levels
Automatic functions
▪Continuously variable speed adjustment depending on the mode of operation
▪Soft start (limitation of starting current)
▪Full motor protection with integrated trip electronics
▪Setback operation
Manual functions
▪Setting the operating mode
▪Setting the differential pressure setpoint
▪Setting the speed level
▪Vent function
▪Deblocking the rotor
Signalling and display functions
▪Alternating display of flow rate, head and electrical input power
▪Error codes indicated on the display

4 Description of the Pump (Set)
15 of 44
Calio S / Calio-Therm S
4.5 Configuration and function
1
2
4
5
6
7
3
8
9
10
11
12
13
Fig.2: Description and sectional drawing of the pump set
1 Pump casing 8 Discharge nozzle
2 Thermal insulation shell 9 Radial plain bearing
3 Control panel 10 Impeller
4 Display 11 Motor
5 Control element (3control buttons) 12 Suction nozzle
6 Vent plug/ deblocking 13 Motor shaft
7 Connection to power supply (plug-
type connector)
Design The pump is designed with a radial fluid inlet (suction nozzle) and a radial outlet
(discharge nozzle) arranged on the same axis. The impeller is rigidly connected to the
motor shaft. Mechanical sealing is not required as the rotating assembly is completely
isolated from the stator winding. The rotating assembly is lubricated and cooled by
the fluid handled. The motor housing is equipped with a plug-type connector. The
lubricating system and high-quality ceramic bearings ensure smooth running and a
long service life. The integrated continuously variable differential pressure control
and operating software enable an optimum adjustment of the pump to changing
operating conditions and minimise operating costs. The combination of an efficient
hydraulic system with a high-efficiency electric motor makes sure that the input
power is converted into hydraulic energy as efficiently as possible.
Function The fluid enters the pump via the suction nozzle (12) and is accelerated outward in a
cylindrical flow by the rotating impeller (10). In the flow passage of the pump casing
the kinetic energy of the fluid is converted into pressure. The fluid is pumped to the
discharge nozzle (8), where it leaves the pump. The shaft runs in radial plain bearings
(9), which are supported by the motor (11).
4.6 Noise characteristics
Table6: Noise characteristics
Size Average sound pressure level
All Max. 30dB (A)

4 Description of the Pump (Set)
16 of 44 Calio S / Calio-Therm S
4.7 Dimensions and weight
For dimensions and weights please refer to the type series booklet of the pump (set).
4.8 Scope of supply
Depending on the model, the following items are included in the scope of supply:
▪Pump set
▪Sealing elements
▪Plug-type connector
▪Two-piece thermal insulation shell (for CalioS only)
▪Installation/operating manual
4.9 Accessories
No accessories available.

5 Installation at Site
17 of 44
Calio S / Calio-Therm S
5 Installation at Site
5.1 Safety regulations
DANGER
Installation in potentially explosive atmospheres
Explosion hazard!
▷Never install the pump in potentially explosive atmospheres.
▷Observe the information given in the data sheet and on the name plates of the
pump system.
DANGER
Calio S pump used for drinking water or foodstuff applications
Danger of poisoning!
▷The pump materials are not suitable for drinking water applications or
foodstuff applications.
Never use this pump for drinking water applications or foodstuff applications.
▷For drinking water applications and foodstuff applications only use the pump
type Calio-ThermS.
5.2 Checks to be carried out prior to installation
Before beginning with the installation check the following:
▪The pump set can be operated on the power supply network according to the
data on the name plate.
▪The fluid to be handled matches the description of suitable fluids.
(ðSection6.2.4.1,Page25)
5.3 Installing the pump set
DANGER
Leakage at the pump
Hot fluids escaping!
▷Fit the sealing elements and make sure they are positioned correctly.
CAUTION
Ingress of fluid into the motor
Damage to the pump set!
▷Install the pump set with the pump shaft in a horizontal position. Connect the
piping without transmitting any stresses and strains.
▷Never install the pump set with the motor terminal box pointing downwards.
▷Undo the hexagon socket head cap screws. Then turn the motor housing.
CAUTION
Air entering the pump
Damage to vertically installed pump sets whose direction of flow is downwards!
▷Fit a vent valve at the highest point of the suction line.

5 Installation at Site
18 of 44 Calio S / Calio-Therm S
NOTE
We recommend installing shut-off valves upstream and downstream of the pump.
Make sure that no leaking water can drip into the pump motor or terminal box.
NOTE
The direction of flow of a vertically installed pump should be upwards.
NOTE
Do not install the pump at the lowest point of the system to prevent any impurities
from collecting in the pump.
The control panel can be turned. The position must be effected with the pump set
removed from the system.
1. Undo and store the 4 hexagon socket head cap screws.
2. Rotate the drive unit until it has reached the required position. Compare it
against the permissible installation positions. Adjust the position if required.
3. Fit and tighten the 4 hexagon socket head cap screws again.
Permissible installation positions
✔
✔
Fig.3: Permissible installation positions
DANGER
Leakage at the pump
Leakage of hot fluids!
▷Insert the O-ring in the correct position.
Screw-ended pump 1. Position the pump set as indicated in an easily accessible place.
ðAn arrow on the pump casing and thermal insulation shell indicates the
direction of flow.
2. Accurately insert the sealing element.
3. Connect the pump and piping with a pipe union.
4. Tighten the pipe union hand-tight with an assembly tool (e.g. pipe wrench).
5. Accurately insert the sealing element in the opposite pipe union.
6. Tighten the pipe union hand-tight with an assembly tool (e.g. pipe wrench).

5 Installation at Site
19 of 44
Calio S / Calio-Therm S
5.4 Connecting the piping
WARNING
Hot surface
Risk of burns
▷Never touch a pump set when it is in operation.
WARNING
Impermissible loads acting on the pump nozzles
Risk of burns by hot fluids escaping!
▷Do not use the pump as an anchorage point for the piping.
▷Anchor the pipes in close proximity to the pump and connect them without
transmitting any stresses or strains.
▷Take appropriate measures to compensate for thermal expansion of the piping.
CAUTION
Contamination/dirt in the piping
Damage to the pump!
▷Flush the piping prior to commissioning or replacing the pump. Remove any
foreign matter.
NOTE
Installing check and shut-off elements in the system is recommended, depending on
the type of plant and pump. However, such elements must not obstruct proper
drainage or hinder disassembly of the pump.
üSuction lift lines have been laid with a rising slope, suction head lines with a
downward slope towards the pump.
üThe nominal diameters of the pipelines are equal to or greater than the nominal
diameters of the pump nozzles.
üThe pipelines have been anchored in close proximity to the pump and connected
without transmitting any stresses or strains.
1. Thoroughly clean, flush and blow through all vessels, pipelines and connections
(especially of new installations).
CAUTION
Welding beads, scale and other impurities in the piping
Damage to the pump!
▷Free the piping from any impurities.
5.5 Enclosure/insulation
WARNING
The pump takes on same temperature as the fluid handled
Risk of burns!
▷Insulate the volute casing.
▷Fit protective equipment.

5 Installation at Site
20 of 44 Calio S / Calio-Therm S
NOTE
CalioS/ Calio-ThermS models with an overall length of 180mm are supplied with a
thermal insulation shell.
5.6 Electrical connection
DANGER
Electrical connection work by unqualified personnel
Danger of death from electric shock!
▷Always have the electrical connections installed by a trained and qualified
electrician.
▷Observe regulations IEC60364.
DANGER
Work performed on an energised plug-type connector
Danger of death from electric shock!
▷Switch off the power supply prior to commencing work and ensure that it
cannot be switched on again unintentionally.
DANGER
Plastic housing opened
Risk of fatal injury due to electric shock!
▷The plastic housing must not be opened.
WARNING
Incorrect connection to the mains
Damage to the mains network, short circuit!
▷Observe the technical specifications of the local energy supply companies.
5.6.1 Connecting the power cable
Table7: Power cable dimensions
Power cable dimensions Values
Outside diameter 5,5 - 10,0mm
Cross-section 0,5 - 1,5mm2 (solid or stranded2))
1. Verify the mains voltage at the site against the data on the name plate.
2. Switch off the power supply and make sure it cannot be switched on again
unintentionally.
3. Fit the union nut and joint ring on the power cable.
4. Guide the power cable through the plug housing until the cable ends are freely
accessible.
5. Strip the power cable as shown in the following illustration.
Strip about 18mm of the earth conductor sheath. Strip about 13mm of the
neutral conductor sheath and Lconductor sheath.
Strip 6mm of each core's sheath as a minimum.
2) Fit wire end sleeves on stranded/flexible cores.