KT&C KNC-SPDNi120HD User manual

IP PTZ SPEED DOME is designed to be installed using a standing bracket on
the wall or ceiling.
Note:
• It is recommended that megapixel lens be used to optimize performance.
• Please keep the lens clean.
• Any foreign objects and nger marks on the lens can cause inferior image quality in low light
level conditions
Plastic anchors(4ea)
Screws(4ea)
Washers(4ea)
Safety Wire
Connect the Camera Safety Wire
to the Installation Base.
③
②
①
M156-IPPTZ12-003
MegaPixel Network Camera
IP PTZ SPEED DOME
Installation Guide
Table of Contents
INTRODUCTION
PACKAGE CONTENTS
HARDWARE INSTALLATION
IP ADDRESS ASSIGNMENT
Introduction
IP PTZ SPEED DOME Installation Guide
This installation guide provides instructions for installing the Network
Camera on your network. For all other aspects of using the product,
please see the User’s Manual, available on the CD included in this
package, or from http://www.ktnc.co.kr
Installation Steps
1. Check the package contents against the list below.
2. Read the product description.
3. Install the hardware, and set RS485 Device Conguration.
4. Set an IP address
5. Set the admin and user ID and password. (See User’s Manual)
Important!
This product must be used in compliance with local laws and regulations.
Ferrite Core
In order to reduce the generation of unnecessary signals, Pass the AC 24V and network cable
through the ferrite core and connect it as the drawing.
Connection Interface and Wiring cables
* Caution
Do not connect the power cable until all other connections have
been completed.
After removing the protection sheet (PE form), supply the power to
the dome camera.
Connecting the RS-485 lines
The dome camera can be controlled remotely by an external device
or control system such as a controller using RS-485 half duplexer
(RS-485 Connection). A repeater is recommended to extend the
connect ion over 1.2 Km.
Connecting Video, Audio In/Out
- Connect the video jack (BNC connector) to the portable display
device (BNC out of the dome camera is provided for installation
and is not recommended for monitoring purposes)
- Connect the audio-in jack(3.5mm) to line level audio source or
MIC.
- Connect the audio-out jack(3.5mm) to speaker.
Connecting Alarms
- Alarm In: You can use external devices to trigger the dome
camera to react to events. Mechanical or electrical switches can be
wired to the AL0 and GND_ARM.
- Alarm Out: The dome camera can activate external devices such
as a buzzer.
Connect the device to NO (or NC) and COM pins.
Connecting the network and the power
The Network Camera connects to the network via a standard
network cable, and automatically detects the speed of the local
network segment (10BaseT/100BaseTX Ethernet). PoE Supported.
If in a non-PoE power supply environment, connect the power
jack(2P-terminal block) to the AC 24V power supply. A regulated
AC24V 2A(With Heater) power supply is recommended for use with
this camera for the most stable operation.
Hardware InstallationConnection
Package Contents
Camera Wall Mount Bracket Software CD Installation Guide
Terminal Block(5p)
Terminal Block(2p)
Coupler
Terminal Block(2p)
L-Wrench
Ferrite Core
Plastic
Anchors(4ea)
Screws(4ea)
Washers(4ea)
Screws / Plastic Anchors / L-wrench / Washers / RJ45 coupler

IP Address Assignment
To make it accessible on the network, the Network Camera must be assigned an IP
address.
Note:
• A network DHCP server is optional.
• The Network Camera has the default IP address 192.168.0.123.
• If IP assignment fails, check that there is no firewall blocking its operation and check that
the Network
Camera and your computer's IP is located on the same subnet.
Assign an IP address using IP Installer
The IP installer automatically search for and displays network devices on your
network. The application can also be used to manually assign a static IP address.
Note:
The computer running the IP installer must be on the same network segment (physical subnet) as the
Network Camera.
1. Check that the Network Camera is connected
to the network and that power has been applied.
2. Start NetCAM installer.
3. When the Network Camera appears in the window, select the Network Camera that
needs to be
assigned the IP address.
A. Refresh Device List – Rescan local network to nd the Network Camera.
B. Authenticate – Enter the administrator ID and password.
C. Host Name – Enter the Host Name of the Network Camera.
D. IP Settings
i. Dynamic – Assign a dynamic IP address automatically from DHCP server on your
network.
ii. Static – Assign a static IP address manually.
iii. Port – Enter the HTTP port the Network Camera will use. The default setting is 80.
Alternatively, any port in the range 1024-65535 may be used, but check rst with
your system administrator before changing the default setting.
E. Network Settings
i. Subnet Mask – Specify the mask for the subnet the Network Camera is located on.
ii. Gateway – Specify the IP address of the default router (gateway) used for connecting
devices attached to different networks and network segments.
iii. Pri. DNS – Enter the IP address of the primary DNS server. This server provides the
translation of host names to IP addresses on your network.
iv. Sec. DNS – Specify the IP address of the secondary DNS server. This will be used if the
primary DNS server is unavailable.
4. Click “Set” button to save that conguration.
Accessing the Network Camera
1. Start your browser.
* When you run or install ActiveX, open the Internet Explorer browser as Administrator on Windows
Vista, 7, 8 (supported only in the Desktop mode).Users without administrator rights cannot install ActivX
controls.
Unless Internet explorer is opened as administrator, The camera functions of Live Web Viewer cannot
work(screen capture, etc.)
2. Enter the IP address or host name of the Network Camera in the Address eld of your
browser.
3. If you are accessing the Network Camera for the rst time, you will see the following
warning message as shown below.
4. Click the warning message and select “Run Add-on” or “Install ActiveX Control…” etc.
5. Click “Install” to install the Web Viewer.
6. If the Windows Security Alert pop-up window appears, click the “Unblock” Button.
7. After installing the Web View ActiveX Control, a Login page will be displayed.
Enter the user ID and password.
Note:
Default User ID and Password is [ID: admin, Password: admin]
8. The video image displays in your browser.
Note:
To view streaming video in Microsoft Internet Explorer, you must set your browser to
allow the “KT&C Web Viewer” to be installed on your computer. This ActiveX component
is installed the first time a video stream is accessed.
Product Specications
ITEM DESCRIPTION
Image Device 1/2.8" (2.38MP) Progressive CMOS Sensor
Lens f=4.8-57.6mm 12x AF Optical Zoom Lens, True D/N
View Angle Approx. 71.7° (WIDE) - 6.7° (TELE)
F-stop F2.2(WIDE) - F2.3(TELE)
Minimum Illumination 0.2 Lux (F2.0, ICR Off, DSS Off) / 0.01 Lux (DSS On)
0.02 Lux (F2.0, ICR On, DSS Off) / 0.001 Lux (DSS On)
VIDEO
Video Codec H.264 Main Prole, Motion JPEG
Resolutions
(H.264/MJPEG)
H.264: Max. 1920x1080@30fps, Min. 720x480@30fps
MJPEG: Max. 1920x1080@30fps, Min. 176x120@30fps
Video Streaming 4 Channel Stream at different frame rate and bandwidth
Image Settings
Brightness, Contrast, Saturation, Sharpness, White
Balance, Exposure Control, Rotation of Images, Text and
Image overlay, Privacy Masking (7 Zones), BLC, HLC,
D-WDR, 3DNR
AUDIO
/ Micro-SD
Audio Streaming Bi-audio, Full Duplex
Audio Codec G.711, G.726
Audio Input / Output Line Input / Output
Micro-SD/SDHC Micro SD card (Max. 32GB)
Network
Security Multiple user access levels with password protection
IP address ltering: Deny, Allow
Supported Protocols
IPv4, HTTP, HTTPS, TCP, RTSP, RTP, UDP, IGMP,
RTCP, SMTP, FTP, ICMP, DHCP, ARP, DNS, DDNS,
UPnP
System
Integration
API Onvif Prole S
Open API for software integration, including API, SDK
Intelligent Video Video motion detection
Alarm Triggers Intelligent video, External inputs, Manual triggers,
Network fail, Reboot, Schedule
Alarm Events File upload via FTP, e-mail
Notication via e-mail, External output activation
Web viewer
Video format change, Stream play / stop, Speaker sound
/ mute, Mic on, Snapshot, Instant recording (Max. 5
minutes), Manual trigger, Output control, Full screen,
Screen magnication, Status indicator (video, audio,
record, alarm, motion), Pan & Tilt / Zoom & Focus /
Speed control, Preset / scan / pattern / tour
PTZ
Pan Angle 360° Continuous Rotation
Tilt Range 0 - 180°
Speed Maximum Preset Speed: 360°/s
Flip Rotate 180° at bottom of tilt
Auto Scan 8 Auto Scan
Preset Position 210 Position
Tour 8 Tour
Pattern 6 Pattern
General
Enclosure Alloy case, Ivory
IP Rating IP66 (Weatherproof)
Processors and
Memory
CPU: ARM 1136-S
RAM: 256 MB
Flash: 256 MB
Real-time clock with backup battery
Power 24VAC 23W (Heater On) / PoE+ (IEEE 802.3at)
Interfaces
RJ-45 for Ethernet 10baseT/100baseTX with PoE
Micro-SD socket (Max. 32GB)
Terminal Block:
- RS485 TX/RX
- Alarm input
- Alarm out (NO/NC)
3.5 mono jack for Line output & input
connector for Service Video
3.5mm power input: 24VAC
Operating
Temperature -20°C ~ +50°C (-4°F ~ 122°F) (w/ Heater)
Storage Conditions Temperature: -20°C ~ +60°C (-4°F ~ 140°F)
Humidity Max. 90% RH (non-condensing)
Conformity CE, FCC
Dimensions (Bubble Ø112) Ø166 x 341 x 255
Weight Approx. 3500g (7.7 lbs) w/wall mount
Accessories Installation Guide, Software CD