KTI Networks KS-115FM-V User manual

-1-
InstallationGuide
Web Smart Managed
10/100 Fast Ethernet Switches
with VLAN Support
KS-115FM-V
KS-117FM-V
DOC.030430-KS115FM-V-KS117FM-V-K

-2-
(C)2002KTINetworksInc.Allrightsreserved.Nopartofthisdocumen-
tation may be reproduced in any form or by any means or used to make
any directive work (such as translation or transformation) without per-
missionfromKTINetworksInc.
KTI Networks Inc. reserves the right to revise this documentation and to
make changes in content from time to time without obligation on the part
of KTI Networks Inc. to provide notification of such revision or change.
For more information, contact:
UnitedStates KTINetworksInc.
P.O.BOX631008
Houston,Texas77263-1008
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
WWW: http://www.ktinet.com/
International Fax: [phone]
E-mail: [email protected]
WWW: http://www.ktinet.com.tw/

-3-
The information contained in this document is subject to change without prior notice.
Copyright (C) All Rights Reserved.
TRADEMARKS
Ethernet is a registered trademark of Xerox Corp.
This device complies with Class A Part 15 the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received including the interference that may cause.
CISPRACOMPLIANCE:
This device complies with EMC directive of the European Community and meets or exceeds the follow-
ing technical standard.
EN 55022 - Limits and Methods of Measurement of Radio Interference Characteristics of Information
Technology Equipment. This device complies with CISPR Class A.
WARNING: This is a Class A product. In a domestic environment this product may cause radio inter-
ference in which case the user may be required to take adequate measures.
CE NOTICE
Marking by the symbol indicates compliance of this equipment to the EMC directive of the
European Community. Such marking is indicative that this equipment meets or exceeds the following
technical standards:
EN 55022: Limits and Methods of Measurement of Radio Interference characteristics of Information
Technology Equipment.
EN 50082/1:Generic Immunity Standard -Part 1: Domestic Commercial and Light Industry.
EN 60555-2: Disturbances in supply systems caused by household appliances and similar electrical equip-
ment - Part 2: Harmonics.

-4-
Table of Contents
1. Introduction ..................................................................5
1.1 Features ...........................................................................................6
1.2 Specifications ..................................................................................7
1.3FX Port Optical Specifications.........................................................8
1.4 Management Specifications ............................................................9
2. InstallingtheSwitches ...............................................10
2.1 Unpacking ..................................................................................... 10
2.2 Supply the Power .......................................................................... 10
2.3 PortConfiguration ......................................................................... 11
2.4VLANFunction ............................................................................. 12
2.5 DHCPand IPConfiguration........................................................... 15
2.6 Push Button IP SW ....................................................................... 15
2.7 Making UTP Connections ............................................................. 16
2.8 Making Fiber Connection..............................................................17
2.9LEDIndications ............................................................................. 18
3.Web Management ......................................................19
3.1 Web Browser................................................................................. 19
3.2 Port Setup ...................................................................................... 22
3.3 IPSetup ......................................................................................... 23
3.4VLAN Setup .................................................................................. 24
3.4.1Port-basedVLAN ....................................................................... 25
3.4.2802.1QVLAN .............................................................................. 27
.5 Password Setup............................................................................... 30
3.6 RestoreDefault .............................................................................. 31
3.7ReBootDevice............................................................................... 32
3.8 About ............................................................................................33
Appendix:FactoryDefaultValues.................................34
Appendix:Effective Timeof SettingChanges ..............34

-5-
1. Introduction
This guide describes the specifications and installation instructions for
the following two managed 10/100 switch series:
KS-115FM-V series
•Four 10/100BASE-TX auto-negotiation TP switched ports
•One100BASE-FXFiberswitchport
•Web-based device management support
•Compact Fast Ethernet switch
KS-117FM-V series
•Six 10/100BASE-TX auto-negotiation TP switched ports
•One100BASE-FXFiberswitchport
•Web-based device management support
•Compact Fast Ethernet switch

-6-
1.1 Features
• The 10/100BASE-TX switched ports support:
- Auto speed sensing for 100Mbps or 10Mbps connection
- Auto configuration for connected auto-negotiation devices
- Full-duplexorhalf-duplexoperation
- Port configuration can be changed via web management interface
• The 100BASE-FX switched port supports:
- 100Mbps full duplex connection
- Varietyof fiberconnectorssuch asST,SC,MT-RJ, LCandVF-45
- Multimode and single mode fiber cables (model dependent)
• Provide the following switch functions:
- Self learning for active MAC addresses up to 2K entries
- Store and forward switching that only good packets are forwarded
- Forwarding and filtering at full wire speed
- Flow control for traffic congestion
- Broadcast packet storm protection
- Port-based VLAN function
- IEEE802.1QVLANfunction
• Provide the following management functions:
- Web-base interface for easy management
- DHCP support for IP configuration
- Static IP configuration if DHCP is not available
- Port status and configuration
- VLANconfiguration
- Security check for management login
- Restore factory default settings
- Remote boot
• ComprehensiveLED indicators

-7-
1.2 Specifications
Figure:MajorComponentsonPanels(Ex.KS-117FM-V)
KS-115FMP1-P4 Port 1 ~ Port 4 Twisted-pair switched ports (TP ports)
KS-117FMP1-P6 Port 1 ~ Port 6 Twisted-pair switched ports (TP ports)
TPPort IEEE802.310BASE-T,IEEE802.3u100BASE-TXstd.
Shielded RJ-45 jacks with Auto MDI-X detection
Auto-negotiation capable
Speed for 10Mbps or 100Mbps
Full-duplex or half-duplex support
FXPort IEEE802.3u100BASE-FXcompliant
Fixed100MbpsFull-duplexoperation
Flowcontrol IEEE 802.3x pause packet for fullduplexoperation
Back pressure for half duplex operation
Cables 10BASE-TCat.3, 4,5or higher(100metersmax.)
100BASE-TXCat.5,5eorhigher(100metersmax.)
100BASE-FXmultimodeorsingle mode fiber cable
LEDindicators Power status
TPports: Speed,Link/Activity, Duplex/Collisionstatus
FX port : Link/Activity,Duplex/Collisionstatus
Filteringrate 14,880ppsforEthernet (10BASE-T)
148,800ppsforFast Ethernet (100BASE-TX)
Forwardingrate 14,880ppsforEthernet(10BASE-T)
148,800ppsforFast Ethernet (100BASE-TX)

-8-
Filteringaddress Multicast/Broadcast/Unicast address
MACaddress 2K entries
Agingtime 300 seconds
Prioritylevels 2 outgoing priority queues (Ratio: High/Low = 4/1 )
VLANmode 1. Port-based VLAN 2.802.1QVLAN(Tag-based)
VLANgroups 16 groups (Group 0 ~ 15)
PortPVID Full 12-bit VID, per port setting
PortTagMode Tag/Untag mode, per port setting
Environment Temperature 0oCto 40oC
Relativehumidity 10% to 90% non-condensing
Dimensions 144mmx100mmx26mm(WxDxH)
5.67x3.94x1.02inch
DCINPower Rating+7.5Vmin.1A
DCINJack D6.3mm D2.0mm
Operatingvoltage +6.5~+12.5VDC(DeviceDCInput)
Power Consumption 7W max. (with power adapter)
1.3 FX Port Optical Specifications
Model Ext. Connector Wavelength Tx optical powerRx sensitivity
-VT MM*1 ST 1310nm -20 ~ -14dBm -31dBm
-VC MMSC 1310nm -20 ~ -14dBm -31dBm
-VJM MMMT-RJ 1310nm -20 ~ -14dBm -31dBm
-VVM MM VF-45 1310nm -20 ~ -14dBm -31dBm
-VL MMLC 1310nm -19 ~ -14dBm -34dBm
-VSA2 SM*2 SC 1310nm -15 ~ - 8dBm -31dBm
*1 : Multimode fiber
*2 : Single Mode fiber

-9-
1.4 Management Specifications
Interface In-band web browser for IE4.0 and Netscape4.x
Pingcommand,ARPcommand
Protocols IPv4,ARP, ICMP,UDP,TCP,DHCP client, Http server
IPSetting DHCP dynamic IP mode(defaultmode)
StaticIPmode (default:192.168.0.2)
DHCP DHCP client ID = Device modelname + MAC address
Security Login password checking
Password setting (default : 123)
Port All ports : port status monitoring
Monitoring Link, Speed, Duplex, Flow control status
Port Per TP port configuration settings
Control Auto-negotiation function : enable, disable
Speed:100M,10M
Duplex:full,half
VLAN VLAN mode selection: Port-based, 802.1Q (Tag-based)
Port-based 16VLANgroups
VLAN Member ports setting for each group
PVID(12-bit VLAN ID value) setting for each port
802.1Q 16VLANgroups
VLAN Member ports setting for each group
PVID(12-bit VLAN ID value) setting for each port
Tag/Untag mode setting for each port
Restore Restore factory default settings
Default Refer to Appendix for factory default settings
Reboot In-band remote boot the switch

-10-
2. Installing the Switches
2.1 Unpacking
Check to see that you have everything before you start the installation.
• Installation guide
• The switch unit
• Rubber magnet stand
• One AC power adapter for the unit
2.2 Supply the Power
CheckingACPower
Before you begin the installation, check the AC voltage of your area. The
ACpoweradapterwhichis usedtosupply theDCpower fortheunit should
have the AC voltage matching the commercial power voltage in your area.
The specifications of the AC power adapter are:
• AC inputpower: AC power voltage of your area
• DC output power: Rating+7.5VVDCmin.1.0A
• DC plug type:
DCINJack
The DC power jack for the AC power adapter is located on the rear of the
switch. Refer to section 1.2 drawing.
InstallingtheSwitch
1. Install the switch with the AC power adapter provided.