Kubota L3200 User manual

CONTENTS
ASSEMBLY INSTRUCTIONS ..................................................................................... 1
TO THE DEALER..................................................................................................... 1
SAFETY ................................................................................................................... 1
CONTENT OF PARTS IN THE CRATE................................................................... 2
Locations and Removal of Parts in the Crate ...................................................................2
Parts in the Carton Box and Paper Bag............................................................................5
TIGHTENING TORQUE OF BOLT AND NUTS....................................................... 9
ASSEMBLY OF TRACTOR ................................................................................... 10
Seat ................................................................................................................................ 10
Position Light Stay .......................................................................................................... 11
ROPS.............................................................................................................................. 12
PTO Shaft Cover ............................................................................................................ 17
Three Point Linkage........................................................................................................ 17
Fender and Reflector...................................................................................................... 18
Number Plate.................................................................................................................. 20
Rearview Mirror .............................................................................................................. 22
Auxiliary Step..................................................................................................................23
Front Axle ....................................................................................................................... 23
Crate Base......................................................................................................................28
Rear Wheel.....................................................................................................................29
Front Wheel ....................................................................................................................30
Front Bumper and Front Hitch ........................................................................................ 32
Drawbar .......................................................................................................................... 32
Battery ............................................................................................................................ 33
Steering Wheel ............................................................................................................... 33
CHECKING THE BATTERY .................................................................................. 35
Battery Checking ............................................................................................................ 35
Battery Charging............................................................................................................. 35
JIG KIT FOR ASSEMBLY ...................................................................................... 37
CHECK LIST FOR INSPECTION AFTER ASSEMBLY ......................................... 39

1ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
TO THE DEALER
1. This manual contains procedures intended to assist
the dealer in unpacking and assembling the product
before delivering to the customer.
The customer's purchase is based on confidence in
both the product and your store. Observe the
procedures in this manual to assemble and adjust
equipment for your customer's safety and satisfaction.
When fully assembled, check function of each part and
feature.
2. The following safety alert symbol marks and
indications are found throughout this manual in steps
where particular attention is required so as to ensure
your safety and to avoid product damage. Observe
the instructions in these warnings where indicated.
SAFETY
To prevent accidents, read through the following items
before starting work, and always regard safety when
working. It is your responsibility to ensure your safety on
the job.
(1) Preparations
1. Select a work site which is level, has sufficient space,
and is not close to dangerous objects.
2. Avoid poorly ventilated rooms.
Asphyxiation from exhaust fumes
is always a possibility that
accompanies running an engine.
3. Working clothes which may be
pinched or caught in the
equipment must not be worn.
Loose clothing can cause serious
injury or death.
4. Always wear a mask and
protective goggles during work
when dust or flying debris may be
thrown by equipment.
(2) Assembly and adjustments
1. Before assembling equipment,
read the assembly instructions for
the product to become familiar
with the equipment and
procedures.
2. Use only adequate and required
equipment, tools and instruments
(e.g. torque wrench, battery
hydrometer and etc.).
3. Set the parking brake and block
wheels to prevent machine (or
tractor) movement.
4. Lower the attachment or
implement to the ground before
assembling or adjusting
equipment.
5. Before working under suspended
or raised equipment, support the
equipment or attachment to
prevent the machine from falling
or moving out of place.
6. Keep fire from cigarettes,
matches or other ignition sources
away from fuel, oil, antifreeze and
other flammable materials.
Indicates an imminently
hazardous situation which, if not
avoided, will result in death or
serious injury.
Indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
Indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
Indicates that equipment or
property damage could result if
instructions are not followed.
Gives helpful information

ASSEMBLY INSTRUCTIONS2
(3) After assembly check
1. Before operating or test driving the equipment, read
and understand the operator's manual.
2. Once the equipment is fully
assembled, select a safe place
for a test run. Prevent onlookers
from approaching the equipment.
To avoid personal injury or
death:
ADo not start engine or
operate levers from
anywhere other than the
seat.
To avoid personal injury:
ADo not bypass-start the
equipment. Short circuiting
the starter terminal runs the
risk that the equipment will
start operating or moving
unexpectedly.
CONTENT OF PARTS IN THE CRATE
BLocations and Removal of Parts in the
Crate
CTools Required
Spanner (12 mm, 14 mm) or socket with ratchet wrench
or impact wrench, nipper.
1. Check, the exterior parts and accompanying
accessories for scratches and problems.
ALoosen the bolts and remove the metallic frames. Be
careful not to scratch the tractor.
2. Remove the upper frame (1).
3. Remove the left frame (2).
[Rear mount type ROPS]
[Mid mount type ROPS]
(1) Upper frame
(2) Left frame

3ASSEMBLY INSTRUCTIONS
4. Remove the right frame (3).
5. Remove the front frame (4).
6. Remove the rear frame (5).
[Rear mount type ROPS]
[Mid mount type ROPS]
ABe careful, the mid mount type ROPS frames are fixed
on the right side of the packing.
7. Remove the plastic cover.
8. Check the attached parts as shown in the photo below.
[Rear mount type ROPS]
[Mid mount type ROPS]
(3) Right frame
(4) Front frame
(5) Rear frame
(6) Bumper
(7) Bevel gear case assembly
(8) ROPS rear lower frame RH
(9) ROPS rear lower frame LH
(10) PTO protector
(11) ROPS upper frame (mid mount type)
(12) ROPS rear frame RH
(13) ROPS rear frame LH

ASSEMBLY INSTRUCTIONS4
[Rear mount type ROPS]
[Mid mount type ROPS]
(14) Yoke shaft RH (for 4WD)
(15) Position light stay RH
(16) Lower link assembly LH and RH
(17) Auxiliary step LH
(18) ROPS rear upper frame
(19) ROPS frame RH (mid mount type)
(20) ROPS frame LH (mid mount type)
(21) Steering wheel, steering pad and nut
(10) PTO protector
(14) Yoke shaft RH (for 4WD)
(22) Drawbar
(23) Tool box
(24) Carton box 1
(25) Carton box 2
(26) Paper bag 1
(27) Paper bag 2

5ASSEMBLY INSTRUCTIONS
BParts in the Carton Box and Paper Bag
1. Open the carton box 1 and check the contents.
A: DW-EC, B: DW-UK, C: DR-NEC
[Plastic bag 1]
A: DW-EC, B: DW-UK, C: DR-NEC
No. DESCRIPTION UNIT REMARKS
ABC
1Mirror 111
2 Plastic bag 4 1 1 1
3 Holder, license light 1 1 1
4 Assembly light, license 1 1 1
5 Operator's manual 1 1 1
6 Assembly instructions 1 1 1
7 Hitch, front 1 1 1
8 Support, fender 2 2 2
9 Holder, reflector 2 2 2
10 Holder, cup 1 1 1 Fender
11 Wire harness - 1 - License light
12 Plastic bag 1 1 1 1
13 Plastic bag 2 1 1 1
14 Plastic bag 3 1 1 1
No. DESCRIPTION UNIT REMARKS
ABC
1 Bolt (M16 x 30) 8 8 8 Rear wheel
2 Nut (M16) 4 4 4 Rear wheel
3 Washer, spring (M16) 4 4 4 Rear wheel
4 Nut (M14) 12 12 12 Front wheel
5 Washer, plain (M14) 12 12 12 Front wheel
6 Washer, spring (M14) 12 12 12 Front wheel

ASSEMBLY INSTRUCTIONS6
[Plastic bag 2]
A: DW-EC, B: DW-UK, C: DR-NEC
[Plastic bag 3 and 4]
A: DW-EC, B: DW-UK, C: DR-NEC
No. DESCRIPTION UNIT REMARKS
ABC
1 Bolt (M14 x 35) 4 4 4 Bumper
2 Bolt (M10 x 35) 4 4 4 Hitch, front
3 Assembly pin 1 1 1 Hitch, front
4 Bolt, flange (M8 x 12) 4 4 4 Support, fender
5 Bolt, flange (M8 x 16) 2 2 2 Fender
6 Plug 2 2 2 Fender
7 Pin, joint 1 1 1 Drawbar
8 Pin, snap 1 1 1 Drawbar
9 Bolt (M8 x 75) 1 1 1 Holder,
license light
10 Washer, plain (M8) 1 1 1 Holder,
license light
11 Key 2 2 2
12 Screw, tapping (M6 x 16) 444
Holder,
reflector
13 Screw, tapping (M5 x 8) 222
Assembly
light, license
(A) Plastic bag 3
(B) Plastic bag 4
No. DESCRIPTION UNIT REMARKS
ABC
1 Reflector 2 2 2 Holder, reflector
2 Spanner (14 x 17) 1 1 1
3 Spanner (12 x 10) 1 1 1
4 Screw driver 1 1 1
5 Stay, rearview mirror 1 1 1
6 Bolt, flange (M8 x 16) 2 2 2 Rearview mirror
7 Bolt, flange (M6 x 25) 4 4 4 Rearview mirror

7ASSEMBLY INSTRUCTIONS
2. Open the carton box 2 and check the contents.
A: DW-EC, B: DW-UK, C: DR-NEC
3. Open the paper bag 1 and check the contents.
A: DW-EC, B: DW-UK, C: DR-NEC
(A) Mid mount type ROPS
(B) Rear mount type ROPS
No. DESCRIPTION UNIT REMARKS
ABC
1 Set, bolt - - 2
2 Washer, plain (M16) - - 2
3 Castle nut (M16) - - 2
4 Pin, split - - 2
5 Bolt (M16 x 40, 9T) - - 8
6 Connector - - 1
7 Bolt (M14 x 30, 9T) - - 10
8 Set, bolt 2 2 -
9 Washer, plain (M16) 6 6 -
10 Castle nut (M16) 2 2 -
11 Pin, split 2 2 -
12 Bolt (M14 x 30, 9T) 88 -
4CBKCADCP016A
4CBKCADCP016A
4CBKCADCP016A
ŋ
Ōō
Ŏ
ŏ
Ő
ő
AB
Œ
œŔ
ŕ
Ŗ
No. DESCRIPTION UNIT REMARKS
ABC
1 Pivot pin, lower link 2 2 2
2 Bolt (M10 x 20) 2 2 2
3 Pin, lift rod 2 2 2
4 Pin, snap 2 2 2
4CBKCADCP017A
4CBKCADCP017A
4CBKCADCP017A4CBKCADCP017A
ŋ
Ō
ō
Ŏ

ASSEMBLY INSTRUCTIONS8
4. Open the paper bag 2 and check the contents.
A: DW-EC, B: DW-UK, C: DR-NEC
No. DESCRIPTION UNIT REMARKS
ABC
1 Bolt (M8 x 30) 6 6 6 Fender
2 Washer, plain (M8) 6 6 6 Fender
3 Collar 6 6 6 Fender
4 Cushion 2 2 2 Fender
5 Washer, spring (M12) 1 1 1 Steering wheel
6 Castle nut 1 1 1 Tie rod RH
7 Pin, split 1 1 1 Tie rod RH
8 Band, cord 1 1 1 Wire harness trailer
9 Bolt, flange (M8 x 16) 6 6 6 Fender
10 Nut, flange (M8) 2 2 2 Fender
11 Bolt, flange (M8 x 16) 4 4 4 Step, aid LH
12 Bolt, flange (M8 x 16) 444Stay, position light

9ASSEMBLY INSTRUCTIONS
TIGHTENING TORQUE OF BOLT AND NUTS
1. General screws, bolts and nuts.
Screws, bolts and nuts should be tightened according to the table shown below.
Indication on
top of bolt
Material of
threaded hole
Unit
Diameter N-m kgf-m ft-lbs N-m kgf-m ft-lbs N-m kgf-m ft-lbs N-m kgf-m ft-lbs N-m kgf-m ft-lbs
M6
(6 mm, 0.24 in.)
7.85
to
9.31
0.80
to
0.95
5.79
to
6.87
7.85
to
8.82
0.80
to
0.90
5.79
to
6.50
9.81
to
11.2
1.00
to
1.15
7.24
to
8.31
7.85
to
8.82
0.80
to
0.90
5.79
to
6.50
12.3
to
14.2
1.25
to
1.45
9.05
to
10.4
M8
(8 mm, 0.31 in.)
17.7
to
20.5
1.8
to
2.1
13.1
to
15.1
16.7
to
19.6
1.7
to
2.0
12.3
to
14.4
23.6
to
27.4
2.4
to
2.8
17.4
to
20.2
17.7
to
20.5
1.8
to
2.1
13.1
to
15.1
29.5
to
34.3
3.0
to
3.5
21.7
to
25.3
M10
(10 mm, 0.39 in.)
39.3
to
45.1
4.0
to
4.6
29.0
to
33.2
31.4
to
34.3
3.2
to
3.5
23.2
to
25.3
48.1
to
55.8
4.9
to
5.7
35.5
to
41.2
39.3
to
44.1
4.0
to
4.5
29.0
to
32.5
60.9
to
70.6
6.2
to
7.2
44.9
to
52.0
M12
(12 mm, 0.47 in.)
62.8
to
72.5
6.4
to
7.4
46.3
to
53.5
77.5
to
90.2
7.9
to
9.2
57.2
to
66.5
62.8
to
72.5
6.4
to
7.4
46.3
to
53.5
103
to
117
10.5
to
12.0
76.0
to
86.7
M14
(14 mm, 0.55 in.)
108
to
125
11.0
to
12.8
79.6
to
92.5
124
to
147
12.6
to
15.0
91.2
to
108
167
to
196
17.0
to
20.0
123
to
144
M16
(16 mm, 0.63 in.)
167
to
191
17.0
to
19.5
123
to
141
197
to
225
20.0
to
23.0
145
to
166
260
to
304
26.5
to
31.0
192
to
224
M18
(18 mm, 0.71 in.)
246
to
284
25.0
to
29.0
181
to
209
275
to
318
28.0
to
32.5
203
to
235
344
to
402
35.0
to
41.0
254
to
296
M20
(20 mm, 0.79 in.)
334
to
392
34.0
to
40.0
246
to
289
368
to
431
37.5
to
44.0
272
to
318
491
to
568
50.0
to
58.0
362
to
419
Cast Iron or Steel Aluminum Cast Iron or Steel Aluminum Cast Iron or Steel
No-grade or 4T 7T 9T
Material of bolt SS400, S20C S43C, S48C SCr435, SCM435

ASSEMBLY INSTRUCTIONS10
2. Stud bolts.
Stud bolts used in front and rear axle hubs should be
tightened according to the table shown below
AStud bolts should be inserted so that side "A" (flat
side) is towards the inside and "B" (round side) is
towards the outside of the axle hub.
ASSEMBLY OF TRACTOR
BSeat
CTools required
Spanner (12 mm) or socket with ratchet wrench and
torque wrench.
1. Remove the retainer (1) of the rear upper side.
2. Place the sheet suspension and sheet together on the
sheet support (4). Use the threaded holes "A" on the
sheet suspension and the holes "B" on the sheet
support (4) to mount them, by the bolts (M8 x 20) (5)
as shown in the photo below.
(A) "FLAT"
(B) "ROUND"
Material of
threaded hole
Unit
Diameter
N-m kgf-m ft-lbs N-m kgf-m ft-lbs
M8
(8 mm, 0.31 in.)
11.8
to
15.6
1.2
to
1.6
8.68
to
11.5
8.82
to
11.8
0.90
to
1.2
6.51
to
8.67
M10
(10 mm, 0.39 in.)
24.6
to
31.3
2.5
to
3.2
18.1
to
23.1
19.7
to
25.4
2.0
to
2.6
14.5
to
18.8
M12
(12 mm, 0.47 in.)
29.5
to
49.0
3.0
to
5.0
21.7
to
36.1
31.4 3.2 23.1
M14
(14 mm, 0.55 in.)
63.7
to
73.5
6.5
to
7.5
47.0
to
54.2
M16
(16 mm, 0.63 in.)
10.0
to
11.5
98.1
to
113
72.3
to
83.2
M18
(18 mm, 0.71 in.)
172
to
201
17.5
to
20.5
126
to
148
Cast Iron or Steel Aluminum
(1) Retainer
(2) Bolt
(3) Sheet suspension

11ASSEMBLY INSTRUCTIONS
3. Tighten the all bolts (M8 x 20) (5).
CTightening torque
BPosition Light Stay
CTools required
Spanner (12 mm, 14 mm) or socket with ratchet wrench or
impact wrench and torque wrench.
1. Remove the right side retainer (for mid mount ROPS
type) (1).
2. Assemble the position light stay RH (2) to the right side
step, using the flange bolts (3).
(4) Sheet support
(3) Sheet suspension
(4) Sheet support
(5) Bolts (M8 x 20)
Bolt (M8) : 23.6 to 27.4 N-m
2.4 to 2.8 kgf-m
17.4 to 20.2 ft-lbs
(1) Retainer
(2) Position light stay RH
(3) Bolt (M8 x 16)

ASSEMBLY INSTRUCTIONS12
3. Through the position light harness (5) in the position
light stay (2) from upper side.
4. Connect the position light harness (4) with wire
harness from position light (5).
CRefer to the table below to connect the wire
harness.
5. Stretch the position light harness (5) then clamp it at
the three holders (6). Refer to photo below.
BROPS
CTools required
Pliers. Spanner (14 mm, 19 mm, 22 mm and 24 mm) or
socket with ratchet wrench or impact wrench and torque
wrench. Lift sling.
To avoid personal injury:
ABe careful to the lifting to avoid back injury,
especially when lifting the ROPS lower frame.
1. Remove the ROPS upper frame and ROPS lower
frames by hand after cutting the ROPS bind wire.
[Rear mount type ROPS]
2. Remove the plugs (1) of the rear axle case.
(2) Position light stay RH
(4) Position light harness
(5) Wire harness from position light
Harness side Position light side
Winker lamp Red white Red white
Position lamp Yellow black Yellow black
Ground Black Black
(5) Wire harness from position light
(6) Holder
(A) "PUSH"
(1) Plug

13ASSEMBLY INSTRUCTIONS
3. Assemble the ROPS lower frame RH (2) and LH (3)
temporarily to the rear axle case.
4. Install the ROPS upper frame (5) to the ROPS lower
frame (2), (3) by using a lift sling (6). Then install the
pivot pins.
5. Insert the pivot bolts (7), plain washers (8) and castle
nuts (9) to ROPS lower frame hole as shown in the
photo below.
6. Tighten the bolts
CTightening torque
7. Tighten the pivot bolts (7) and castle nuts (9) until the
ROPS upper frame (5) dose not fall off by itself while
the horizontal position.
(2) ROPS lower frame RH
(3) ROPS lower frame LH
(4) Bolt (M14 x 30)
(2) ROPS lower frame RH
(3) ROPS lower frame LH
(5) ROPS upper frame
(6) Lift sling
(7) Pivot bolt
(3) ROPS lower frame
(5) ROPS upper frame
(7) Pivot bolt
(8) Plain washer
(9) Castle nut
Bolt (M14) : 167 to 196 N-m
17.0 to 20.0 kgf-m
123 to 144 ft-lbs
(5) ROPS upper frame
(7) Pivot bolt
(9) Castle nut

ASSEMBLY INSTRUCTIONS14
To avoid personal injury:
AAdjust the upper ROPS looseness after
confirming that no bystanders are nearby.
ASudden ROPS upper frame looseness may
occur as result of improper adjustment.
AHold the ROPS tightly with both hands and fold
the ROPS slowly and carefully.
AYou should be able to easily fold up the ROPS upper
frame, but the ROPS upper frame should not loosely
drop down its own weight.
8. Install the set bolts (10) to the ROPS lower frame.
9. Insert the snap pins (11) to the set bolts (10).
10.Insert the split pin (12) to the castle nuts (9) of pivot
bolts (7). Bend the split pin (12) certainly as shown
figure below.
[Mid mount type ROPS]
1. Remove the plugs (1) of the rear axle case and
flywheel housing.
2. Install the connector (13) of the ROPS rear frame RH
(2) and LH (3) as shown in the photo below. Tighten
the bolts temporarily.
(7) Pivot bolt
(9) Castle nut
(10) Set bolt
(11) Snap pin
(12) Split pin
(1) Plug
(2) ROPS rear frame RH
(3) ROPS rear frame LH
(4) Bolt (M14 x 30)
(13) Connector

15ASSEMBLY INSTRUCTIONS
3. Assemble the ROPS rear frame RH (2) and LH (3) to
the rear axle case, then tighten the all bolts (4).
CTightening torque
4. Assemble the ROPS frame RH (14) and LH
temporarily to the flywheel housing case.
5. Install the ROPS upper frame (16) to the ROPS frame
RH (14) and LH by using a lift sling (6). Then install the
pivot pins.
(2) ROPS rear frame RH
(3) ROPS rear frame LH
(4) Bolt (M14 x 30)
Bolt (M14) : 167 to 196 N-m
17.0 to 20.0 kgf-m
123 to 144 ft-lbs
(14) ROPS frame RH
(15) Bolt (M16 x 40, T9)
(6) Lift sling
(7) Pivot bolt
(14) ROPS frame RH
(16) ROPS upper frame

ASSEMBLY INSTRUCTIONS16
6. Insert the pivot bolts (7), plain washers (8) castle nuts
(9) to ROPS upper frame hole as shown in the photo
below.
7. Tighten the bolts
8. Tighten the pivot bolts (7) and castle nuts (9) until the
ROPS upper frame (5) dose not fall off by itself while
the horizontal position.
To avoid personal injury:
AAdjust the upper ROPS looseness after
confirming that no bystanders are nearby.
ASudden ROPS upper frame looseness may
occur as result of improper adjustment.
AHold the ROPS tightly with both hands and fold
the ROPS slowly and carefully.
AYou should be able to easily fold up the ROPS upper
frame, but the ROPS upper frame should not loosely
drop down its own weight.
9. Install the set bolts (10) to the ROPS lower frame.
10.Insert the snap pins (11) to the set bolts (10).
11.Insert the split pin (12) to the castle nuts (9) of pivot
bolts (7). Bend the split pin (12) certainly as shown
figure below.
(7) Pivot pin
(8) Plain washer
(9) Castle nut
Bolt (M16) : 260 to 304 N-m
26.5 to 31.0 kgf-m
192 to 224 ft-lbs
(5) ROPS upper frame
(7) Pivot bolt
(9) Castle nut
(7) Pivot bolt
(9) Castle nut
(10) Set bolt
(11) Snap pin
(12) Split pin

17ASSEMBLY INSTRUCTIONS
BPTO Shaft Cover
CTools required
Spanner (17 mm).
1. Remove the two bolts (1) and collars (2) from the
transmission case.
2. Install the PTO shaft cover (3) to the transmission
case, using two bolts (1) and the collars (2) which were
removed from transmission case.
BThree Point Linkage
CTightening torque
CTools required
Pliers. Socket (14 mm) with ratchet wrench and torque
wrench.
1. Install the lower link assemblies (3) with the lower link
pivot pins (2) and tighten the bolts (1).
AMake sure to tighten the lower link pivot pin mounting
bolts with correct tightening torque to prevent the case
from cracking.
2. Fix the lift rod (4) to the lower link assemblies (3) using
the set pins (5) both sides.
(1) Bolts
(2) Collars
(1) Bolts
(2) Collars
(3) PTO shaft cover
Lower link pivot pin bolt : 48.1 to 55.8 N-m
4.9 to 5.7 kgf-m
35.5 to 41.2 ft-lbs
(1) Bolts
(2) Lower link pivot pins
(3) Lower link assemblies
(3) Lower link assemblies
(4) Lift rod
(5) Set pins

ASSEMBLY INSTRUCTIONS18
3. Connect the check chain (6) to the ROPS (7), using
the set pins (8), plain washers (10) and split pins (9)
both sides (right and left side).
4. Split the split pins securely both sides.
BFender and Reflector
CTools required
Pliers, spanner (8 mm, 12 mm) or socket with ratchet
wrench or impact wrench, torque wrench and screwdriver.
1. Assemble the fender supports (10) to the fender
support RH and LH (8).
CTightening torque
ADo not tighten up the all the bolts and nuts to mount
the fenders before to install them all temporally.
Otherwise it makes difficult to assemble the fenders.
2. Insert the cushion (1) to the holes "C" on the fender (2)
as shown in the photo below and figure below.
3. Install the fender RH and LH to the tractor by using the
flange nut (7).
4. Install the collars (5) into the rubber and then
assemble the plain washer (4) and bolts (3). There
three rubber cushion mount of one side.
(6) Check chain
(7) ROPS
(8) Set pins
(9) Split pins
(10) Plain washers
(8) Fender support RH and LH
(9) Flange bolt (M8 x 16)
(10) Fender support
Bolt (M8) : 23.6 to 27.4 N-m
2.4 to 2.8 kgf-m
17.4 to 20.2 ft-lbs
(1) Cushion
(2) Fender
(1) Cushion
(2) Fender
(3) Bolt (M8 x 30)
(4) Plain washer
(5) Collar
(6) Step