Kubota WSM F2880 User manual

Jodale •Perry Corporation
P.O. Box 909
300 Route 100
Morden, Manitoba, Canada
R6M 1A8
Ph: [phone]
Fax: [phone]
Email: [email protected]
Operator’s Manual
This manual must remain with the BOXER ROPS cab:
Serial #:__________________________________
If it is stolen, lost, or misplaced, contact Jodale Perry
for an immediate replacement prior to operating the tractor.
Kubota F2880,3680
BOXER ROPS Cab
Printed in Canada: 2006/06

1.0 Introduction
We at Jodale Perry are pleased that you have chosen a BOXER ROPS cab for your
Kubota F-Series tractor. The BOXER cab has evolved through ideas and
suggestions submitted to us by customers such as yourself.
We ask that you study this manual and adopt the practices outlined in it.
We ask that for practices and operations not outlined in this manual, you follow the
instructions given in the operator’s manual supplied with the tractor. Before
putting the tractor in service, become familiar with all the information described in
both manuals.
Tractor in this manual is defined as the vehicle mounted with BOXER cab (i.e.
tractor, mower, etc.)

2.0 Safety
Carefully review the procedures given in
this manual and the tractor operator’s
manual with all operators annually. It is
important that all operators be familiar
with, and follow, safety precautions.
Operating instructions must be given to
everyone using the tractor before
operation and at least once yearly
thereafter in compliance with OHSA
Regulations 1928.57 (United States).
2.1 General Safety
2.1.1. Never let an unqualified or
untrained driver operator operate the
tractor.
2.1.2. Keep a fire extunguisher, with
ABC rating securely fastened in the cab.
Maintain it and be familiar with its use.
2.1.3. Never carry passengers.
2.1.4. Never operator the tractor in a
closed building. Provide adequate
ventilation. Engine exhaust fumes are
poisonous and can kill.
2.1.5. Always keep sleeves, jackets, or
other clothing relatively tight, and
belted. Loose clothing may catch in
moving parts, and result in personal
injury or death.
2.1.6. Provide a first-aid kit, securely
attached in the cab for use in case of
accident.
2.1.7. Never jump from the tractor.
There is a danger of catching clothing on
protruding parts.
2.1.8. Use steps and handholds when
mounting and dismounting the tractor,
or for servicing components too high to
reach from the ground.
2.1.9. Do not use the cab fender as a step.
2.1.10. Fasten seat belt before starting
the engine. If the tractor is not equipped
with seat belts, purchase approved seat
belts from the tractor manufacturer or
Jodale Perry prior to operating the
tractor.
2.1.11. Safety devices and shields are
intended to protect operators from injury
or death. Under no circumstances
should they be disabled or removed.
2.2 Operating Safety
2.2.1. Always operate the tractor controls
while sitting in the operator’s seat.
2.2.2. Lock seat in position and buckle
seat belt before operating the tractor. If
the tractor is not equipped with seat
belts, purchse approved seat belts from
the tractor manufacturer or Jodale Perry
prior to operating the tractor.
2.2.3. Avoid abrupt turns, starts, or
stops, especially at high speeds.
2.2.4. Keep all shields in place when
operating the tractor.
2.2.5. Do not operate the tractor when
you are tired, sick, or impaired.
2.2.6. Never operate the tractor in
confined areas; visibility nect to the
tractor is reduced. Injury to bystanders,
or damage to the cab or equipment may
result.

2.3 Safe Operation in Rough Terrain
2.3.1. Drive the tractor slowwly on
hillsides and curves to eliminate the
danger of tipping. Avoid slopes which
are too steep for safe operation. Avoid
sharp uphill turns.
2.3.2. Always drive slowly over rough
ground or obstructions. Drive at speeds
slow enough to ensure your safety.
2.3.3. When driving out of a ditch, gully,
or up a steep hillside, engage the clutch
slowly. Avoid sharp uphill turns.
2.3.4. When descending steep grades,
select a sufficiently low gear to maintain
control with minimum braking.
2.3.5. Use caution when driving near the
edge of a ditch or gully. It may cave in,
causeing the tractor to roll over.
2.3.6. Be especially alert when operating
near trees, slopes, and around
obstructions.
2.4 Maintenance Safety
2.4.1. Ensure all hose connections are
tight, and lines and hoses undamaged.
Before disconnecting heater or air
conditioner lines, relieve all pressure.
2.4.2. Remove mud, crop residue, chains,
and tools from steps and operator’s
platform. They may interfere with pedal
operation or entry/exit from tractor.
2.4.3. When servicing components are too
high to reach from the ground use steps
and handholds. Do not use fenders or
shields that are not designed as steps.
2.5 Safe Highway Operation
2.5.1. Before operating tractor on, or
near, public roadways, check with
authorities for local regulations.
2.5.2. Equip towed implements with slow
moving vehicle (SMV) signs when
traveling on public roads.
2.5.3. Install additional lights on
implement rear to safeguard against rear
end collisions.
2.5.4. Use hazard warning flashers as
required by law when transporting or
driven on public roads. If the tractor
warning flashers were removed when
mounting the cabm they must be
replaced prior to operation on public
roads.
2.5.5. Keep to the right, yielding
right-of-way traffic, especially when
pulling implements. Pull off the road
and stop to allow motorists to pass.
Drive on the road shoulder, if permitted
by law.
2.5.6. Use extreme caution when pulling
heavy loads at road speeds. Avoid hard
application of the tractor brakes at high
speed.
2.5.7. Always drive slowly near curbs,
approaches, or ditches.
2.5.8. Ensure headlights are aligned so
they will not blind the operator’s of
oncoming vehicles. If the tractor is not
equipped with turn signals, and law
requires them, install them prior to
operating on or near public roads.
2.5.9. Use your turn signals, checking for
traffic well in advance of turning. If the

tractor is not equipped with turn signals,
and law requires them, install them
prior to operating on or near public
roads.
2.6 Safety decals
2.6.1. Keep decals clean. Remove dirt
with a wet clean cloth when necessary.
2.6.2. Replace safety decals if destroyed,
missing, painted over, or unreadable. IF
the tractor safety decals are covered, or
obscured when the cab is mounted,
purchase replacement decals from the
tractor manufacturer. Mount them in a
readable location at, or near, their
original location before operating the
tractor.
2.6.3. New BOXER cab decals and
tractor decals are available from your
tractor dealer.
2.7 ROPS Cab Safety
2.7.1. Install the ROPS in accordance
with Jodale Perry mounting instructions.
Failure to do so may affect the cab’s
ability to withstand a roll over.
2.7.2. If the ROPS cab is subjected to
alteration, structural damage, or
invovled in an over turn accident, the
entire structure must be replaced.
Failure to do so may result in injury or
death in the event of a roll over.
2.7.3. If the tractor is not equipped with
seat belts, purchase approved seat belts
from the tractor manufacturer prior to
operating the tractor.
2.7.4. Always fasten seat belts prior to
operating the tractor.
2.7.5. Always operate the tractor from
the operator’s seat.
2.7.6. Remove mud, crop residue, chains,
and tools from steps and operator’s
platform. They may interfere with pedal
operation or entry/exit from the tractor.
2.7.7. Remove all loose chains, tools, and
equipment from the cab. Failure to do so
may cause injury or death in the event of
a roll over.
2.7.8. Do not install the cab on a tractor
model that the cab is not designated for
(tractor designation is printed on the cab
serial number plate). Installing the cab
on a non-designated tractor may result
in injury or death.
2.8 Emergency Exits
The typical BOXER cab has two exits
which may be used in an emergency: left
side door, and right escape window.
Right Escape Window Exit:
Lift the window latch arm and push the
window out until the slot in the top
surface of the latch arm is over the latch
arm pin. Push the latch arm down and
away from the pin. Now push the escape
window to a full open position.
Familiarize operators with the
emergency escape window exit prior to
operating the tractor.
The full open position of the escape
window is for emergency exits only. Do
not leave the escape window in the full
open position for normal operation of the
tractor. The escape window may swing
back and break against the side window.

3.0 Operating
Instructions
IMPORTANT
The following section locates, identifies,
and briefly describes the functions of all
cab controls. All operators should
familiarize themselves with control
location and function prior to operating
the tractor. Failure to do so may result
in unsafe operation of the tractor and
possible injury or death to operators and
bystanders.
3.1 Left Switchplate
Controls
The left switchplate is located on the
headliner console left which directly
faces the operator.
1. Front Worklight Switch (optional)
Rocker switch
Low postion: Off
High Position: On
2. Rear Worklight Switch (optional)
Rocker switch
Low position: Off
High position: On
3. Front Wiper Switch (standard)
Rocker switch
Low position: Low
Centre position: Off
High position: Washer*
* if equipped with windshield washer
option only/momentary switch otherwise
4. Rear Wiper Switch (optional)
Rocker switch
Low position: Low
Centre position: Off
High position: Washer*
* if equipped with windshield washer
option only/momentary switch otherwise
5. Heater Switch (optional)
Rotating switch
Set position: Off
Heating position: As knobs turns
counter-clockwise, temperature rises
6. Fan Switch (optional)
Rotating switch
Set position: Off
First position: Low
Second position: Medium
Third position: High
7. Air Conditioner Switch (optional)
Rocker switch
Set position: Off

First position: On
8. Auxiliary Heater Pump (optional)
Push button switch
In position: On
Out position: Off
3.2 Right Switchplate
Controls
The right switchplate is located on the
headliner right side of the console which
faces the operator at an angle
1. Hazard/Beacon Switch (optional)
Rocker switch
Low position: Off
High position: On
2. Turn Signal Lever (optional)
Left position: Left
Right position: Right
3.3 Other Controls
1. Domelight (standard)
The domelight is located in the right rear
corner of the headliner console. It is
adjustable to direct light where required.
Rocker switch
Low position: Off
High position: On
2. Louvers (optional)
The louvers are located on the lower
fascia of the headliner console. They are
adjustable to direct air flow where
required.
An air conditioner recirculation louvre is
provided as a Maximum Cool option is so
equipped.

4.0 Post-Mounting Instructions
Before starting a tractor equipped with a BOXER cab:
1. Clear the cab and tractor of all tools. Tools left in or around the cab and tractor
can cause operator interference which could lead to bodily injury and/or damage to
the machine.
2. Inspect the cab and tractor to ensure all bolts, screws, and heater connections are
tight.
3. Ensure that all pedals, levers, and controls have adequate clearance for normal
operation.
4. Ensure that all electrical components of both the cab and tractor operates
normally.
Start the tractor and run standing at idle for a few minutes. Operate all pedals,
levers, and controls checking for adequate cab clearance. Then run standing at
PTO rpm speed for approximately five minutes and stop the tractor.
1. Inspect the heaters connections for leaks. Tighten as required.
2. Ensure that the water level in the tractor is to the required specification.

5.0 Trouble Shooting
In the following section, Jodale Perry has listed many of the problems, main causes,
and practical solutions to the problems you may encounter. If you encounter a
problem that is difficult to solve, contact your Jodale Perry dealer.
Problem Cause Solution
Poor air circulation Plugged air filter Clean or replace air filter
Too little heat Air lock in system Bleed air out of system
Poor motor circulation Install auxiliary pump
Poor wiper coverage Wipe angle too narrow Increase wipe angle on
motor
Wiper blade contacts Wipe angle too wide Decrease wiper angle on
cab frame motor

6.0 Assembly
The following section consists of component breakdowns of the standard and
optional parts contain in the Jodale Perry BOXER F-Series cab. For your
convenience, part numbers have been assigned to those items, which may be
ordered from Jodale Perry. If a required item doesn not have a part number
associated with it, the part, with an associated part number, which contains that
item must be ordered.
NOTE:
Each figure is only a general depiction of a cab and its components, and may noy
appear exactly the same as the cab you have received.
Figure key:
A/R -as required
LF -linear foot
SF -square foot
TU -tube
U-unit

Kubota F-Series
Item # JDP Part # Assembly Sub-Assembly Description Material Description Qty. Size Unit
ROPS Cab Bracket/Fasteners/Loose Panels
100121 Cab Mount Fasteners Bolt, Flange, 1/2" x 3", Gr. 8, Yellow Dich. 41.000 U
100116 Cab Mount Fasteners Nut, Flange, 1/2", Gr. 8, Yellow Dich. 41.000 U
100450 Cab Mount Fasteners Washer, Steel, Flat, 9/16" x 2 1/2", Yellow Dich. 41.000 U
100449 Cab Mount Fasteners Washer, Rubber, Flat, 9/16" x 2 1/2" 41.000 U
100431 Striker Pin Washer Spacer Washer, 1/2", Gr. 8 41.000 U
100055 Cab Mount Fasteners Washer, Lock, 1/2" 41.000 U
100448 Cab Isolator Mount Isolator, Rubber, 9/16" x 2 1/2" 41.000 U
101630 Front Cab Bracket Weldment 11.000 U
101631 Rear Cab Bracket Weldment 11.000 U
100579 Front Bracket Fasteners Spacer, Buttite, 607-117 11.000 U
101632 Front Bracket Fasteners Bolt, Flange, M10 x 35mm, Gr. 8.8, YD 51.000 U
100020 Front Bracket Fasteners Nut, Flange, M10, Gr. 8.8, YD 61.000 U
101633 Front Bracket Fasteners Bolt, Flange, M10 x 50mm, Gr. 8.8, YD 11.000 U
Item # JDP Part # Assembly Sub-Assembly Description Material Description Qty. Size Unit
Windshield Assembly
100563 Windshield Glass Glass, Tempered, 5MM, Green Tint, Bent 11.000 U
100358 Glass Weatherstrip Rubber, Clip-on, Double Bulb 115.675 LF
100382 Window Glass Bushing Bushing, Rubber, 5MM 41.000 U
100381 Window Glass Bushing Bushing, Rubber, 8MM 41.000 U
100383 Glass Fastener Bolt, Step, 1/4" x 1 1/4", Macro-black 41.000 U
100223 Glass Fastener Nut, Flange, 1/4", Macro-black 41.000 U
Item # JDP Part # Assembly Sub-Assembly Description Material Description Qty. Size Unit
100664 Left Door Assembly
1 100558 Door Glass Glass, Tempered, 5MM, Greylite Tint 11.000 U
2 100358 Glass Weatherstrip Rubber, Clip-on, Double Bulb 113.475 LF
3 100382 Window Glass Bushing Bushing, Rubber, 5MM 51.000 U
4 100362 Boxer Door Glass Bushing Bushing, Rubber, 5MM, Inj-Molded, 3" Hole Centre 41.000 U
5 100003 Glass Fastener Bolt, Step, 1/4" x 1", Macro-black 21.000 U
6 100635 Glass Fastener Bolt, Step, 1/4" x 1 1/2", Macro-black 41.000 U
7 100223 Glass Fastener Nut, Flange, 1/4", Macro-black 61.000 U
9 100565 Door Grab Bar Weldment Weldment 11.000 U
10 100566 Left Door Latch Weldment Weldment 11.000 U
100366 Gas Shock Stud Stud, 10mm 21.000 U

Kubota F-Series
11 100006 Door Latch Latch, Door, Interior, Left 11.000 U
12 100009 Door Push Button Handle Handle, Exterior, Black 11.000 U
13 100011 Door Gasket Rubber, Injection Molded 11.000 U
14 100369 Push Button Hande Extension Bolt Bolt, Hex, 1/4" x 2 1/2" UNC, Plated 11.000 U
15 100007 Door Latch Fasteners Bolt, Flange, M6 x 1.0 x 25MM, Yellow Dichrome 51.000 U
16 100008 Door Latch Fasteners Nut, Flange, M6, Yellow Dichrome 21.000 U
19 100005 Gas Shock Stud Fastener Nut, Serrated, Flange, 5/16", Yellow Dichrome 11.000 U
17 100368 Left Gas Shock Mount Plate Plate, 3/16" 11.000 U
18 100564 Door Hinge Support Weldment Weldment 11.000 U
20 100377 Left Door Hinge Weldment Hinge, Weldment 21.000 U
100026 Hinge Brass Flat Washer Washer, Brass 21.000 U
Item # JDP Part # Assembly Sub-Assembly Description Material Description Qty. Size Unit
Right Escape Window Assembly
1 100561 Escape Window Glass Glass, 5MM, Tinted, Tempered 11.000 U
2 100382 Window Glass Bushing Bushing, Rubber, 5MM 81.000 U
3 100362 Boxer Window Glass Bushing
Bushing, Rubber, 5MM, Injection-Molded, 3" Hole Centre
21.000 U
4 100003 Glass Fastener Bolt, Step, 1/4" x 1", Macro-black 21.000 U
5 100223 Glass Fastener Nut, Flange, Serrated, 1/4", Macro-black 61.000 U
6 100380 Glass Fastener Washer, Flat, 1/4"Wide, Yellow Dichrome 41.000 U
7 100358 Glass Weatherstrip Rubber, Clip-on, Double Bulb, 1/4" 110.908 LF
8 100385 Window Arm Bracket Sheet, 10GA 11.000 U
9 100017 Window Arm Handle, Window Arm, Right 11.000 U
10 100386 Window Latch Fastener Bolt, Carriage, 3/8" x 2 1/2", Yellow Dichrome 11.000 U
11 100018 Window Latch Fastener Nut, Serrated, Flange, 3/8", Yellow Dichrome 11.000 U
12 100019 Window Arm Pin Pin, Window Arm 11.000 U
13 100020 Window Latch Stud Fastener Nut, Flange, M10 x 1.5 11.000 U
14 100378 Right Door Hinge Weldment Hinge, Weldment 21.000 U
15 100026 Hinge Brass Flat Washer Washer, Brass 21.000 U
16 100383 Glass Fastener Bolt, Step, 1/4" x 1 1/4", Macro-black 41.000 U
Item # JDP Part # Assembly Sub-Assembly Description Material Description Qty. Size Unit
Left Side Window Assembly
1 100559 Side Glass Glass, Tempered, 5MM, Greylite Tint 11.000 U
2 100382 Window Glass Bushing Bushing, Rubber, 5MM 81.000 U
3 100003 Glass Fastener Bolt, Step, 1/4" x 1", Macro-black 41.000 U
4 100223 Glass Fastener Nut, Flange, 1/4", Macro-black 41.000 U

Kubota F-Series
5 100380 Glass Fastener Washer, Flat, 1/4"Wide, Yellow Dichrome 21.000 U
6 100358 Glass Weatherstrip Rubber, Clip-on, Double Bulb 19.167 LF
7 100376 Side Window Slide Bolt Bolt, Hex, 5/16" x 1 1/2", Yellow Dichrome 11.000 U
8 100374 Pin Slide Bolt Bolt, Carriage, 5/16" x 1", Yellow Dichrome 11.000 U
9 100033 Latch Bushing Bushing, Latch 21.000 U
10 100027 Window Latch Slider Latch, Left, Interior 11.000 U
11 100005 Window Latch Pin Nut Nut, Serrated, Flange, 5/16", Yellow Dichrome 21.000 U
12 100375 Side Window Arm Bracket Sheet, 10GA 11.000 U
13 100379 Side Window Hinge Weldment Hinge, Weldment 21.000 U
14 100026 Hinge Brass Flat Washer Washer, Brass 41.000 U
Item # JDP Part # Assembly Sub-Assembly Description Material Description Qty. Size Unit
Right Side Window Assembly
100559 Side Glass Glass, Tempered, 5MM, Greylite Tint 11.000 U
100382 Window Glass Bushing Bushing, Rubber, 5MM 81.000 U
100003 Glass Fastener Bolt, Step, 1/4" x 1", Macro-black 41.000 U
100223 Glass Fastener Nut, Flange, 1/4", Macro-black 41.000 U
100380 Glass Fastener Washer, Flat, 1/4"Wide, Yellow Dichrome 21.000 U
100358 Glass Weatherstrip Rubber, Clip-on, Double Bulb 19.167 LF
100376 Side Window Slide Bolt Bolt, Hex, 5/16" x 1 1/2", Yellow Dichrome 11.000 U
100374 Pin Slide Bolt Bolt, Carriage, 5/16" x 1", Yellow Dichrome 11.000 U
100033 Latch Bushing Bushing, Latch 21.000 U
100028 Window Latch Slider Latch, Right, Interior 11.000 U
100005 Window Latch Pin Nut Nut, Serrated, Flange, 5/16", Yellow Dichrome 21.000 U
100375 Side Window Arm Bracket Sheet, 10GA 11.000 U
100379 Side Window Hinge Weldment Hinge, Weldment 21.000 U
100026 Hinge Brass Flat Washer Washer, Brass 41.000 U
Item # JDP Part # Assembly Sub-Assembly Description Material Description Qty. Size Unit
Rear Window Assembly
1 100560 Upper Rear Glass Glass, Tempered, 5MM, Greylite Tint 11.000 U
2 100382 Window Glass Bushing Bushing, Rubber, 5MM 41.000 U
3 100381 Window Glass Bushing Bushing, Rubber, 8MM 41.000 U
4 100383 Glass Fastener Bolt, Step, 1/4" x 1 1/4", Macro-black 41.000 U
5 100223 Glass Fastener Nut, Flange, 1/4", Macro-black 41.000 U
6 100358 Glass Weatherstrip Rubber, Clip-on, Double Bulb 111.917 LF
Item # JDP Part # Assembly Sub-Assembly Description Material Description Qty. Size Unit