KUKEN RH02 User manual

GENERAL INFORMATION
1.Before performing any operation, please read the following instructions carefully. Keep this booklet in a safe place for future
reference.
2.After removing the packaging, make sure that the appliance is in good condition.
3.If you are in doubt, do not use the appliance and return it to your dealer.
4.The packaging materials contain plastic bags which may be hazardous and therefore should not be left within the reach of
children.
5. Before connecting the appliance, make sure that the specifications on the rating plate correspond to the conditions of the
mains supply in your home.
6.The electrical safety of this appliance can only be guaranteed if it has been earthed.
WARNING
1.It is strongly recommended that the electrical installation be carried out by qualified professional personnel.
2.Do not install the appliance in the vicinity of bathtubs, showers, washbasins, swimming pools, etc.
This appliance must only be used for the purpose intended by the manufacturer, which is to heat the area. Any other use is
inappropriate and therefore dangerous. The manufacturer cannot be held responsible for any damage caused by improper and
unreasonable use of this appliance.
4.Do not place a cover over the appliance as this may cause it to catch fire.
5.Do not install accessories or equipment not intended by the manufacturer.
Improper installation may cause damage to persons, animals, objects, etc....
7.Install the appliance only in a horizontal position.
8.Do not install the appliance on a fixed light source or electrical power supply.
9.Avoid installation behind a door.
INSTALLATION
Keep a sufficient distance between the appliance, walls and objects. 2.
2.When the appliance is to be installed in a bathroom, it is necessary to maintain the necessary safety zone around the
appliance.
3.Do not install the appliance in such a way that the heat rays directly hit the walls or adjacent objects.
-For fixing to a wall, proceed as follows:
-Remove a screw from one side to determine the inclination of the appliance.
-Turn the wall bracket to the end of its travel.
-Loosen the screw holding the cover of the wall bracket and remove the cover.
-Determine the location of the appliance and, using the holes in the holes, drill holes in the wall.
-Make two 6 mm holes and insert the supplied plugs.this appliance is intended for fixed installation, i.e. permanent electrical
connection.once the power cable is inserted through the wall bracket, fix the bracket by means of the screws and plugs,
which were previously inserted into the wall.remove the screw from the cable clamp and place the cable in its seat. Make sure
that the cable connections correspond to the symbols stamped on the bracket.
WARNING - THIS EQUIPMENT MUST BE EARTHED.
IMPORTANT
The power cables are coloured according to the following code:
Green and yellow: Earth / Blue: Neutral / Brown : Positive.
The green and yellow wire must be connected to the terminal marked with the letter E or the earth symbol.
The blue wire must be connected to the terminal marked with the letter N or coloured black.
The brown wire must be connected to the terminal marked with the letter L.
Firmly fix the wires, for the cable support by means of the screws.put the cover on the wall bracket and secure it by means of
the appropriate thread.unscrew the screws that regulate the inclination of the appliance.determine the desired heating
inclination and tighten the screws. Do not change the inclination without loosening the appropriate screws..
MAINTENANCE
1.Before carrying out any maintenance operation, disconnect the appliance from the power supply.
2.This appliance does not require any special maintenance. For cleaning, it is recommended to use a soft, damp cloth and a
neutral detergent. Do not use an abrasive cloth or devices that could affect the external appearance of the appliance. Check
that the parts exposed to heat and ventilation rays are free from dust and dirt.
3.During cleaning, take care not to touch the quartz heating elements.
In case of malfunction or breakdown of the appliance, disconnect the appliance from the power supply and contact an
authorised service centre. Always request the use of original spare parts..
TECHNICAL DATA
Power: 600w / 1200w
Voltage: 220v-240v
Frequency: 50Hz