Kwikbit Edge Controller User manual

Edge Controller Guide
Kwikbit Wireless Communication Systems
January 22, 2021

Edge Controller Guide
2 Kwikbit Edge Controller Guide
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
You can determine whether your equipment is causing interference by turning it on and off. If the
interference stops, it was probably caused by the equipment. If the equipment causes interference
to radio or television equipment, try to correct the interference by using one or more of the
following measures:
▪Reorient or relocate the receiving antenna.
▪Increase separation between the equipment and receiver.
▪Connect the equipment into an outlet on a circuit different from which the receiver is
connected.
▪Consult the dealer or an experienced radio/TV technician.
Any modifications to this product which are not authorized by Kwikbit Inc. could void your authority
to operate this equipment.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT
NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT
ARE PRESENTED WITHOUT WARRANTY OF ANY KIND. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF
ANY PRODUCT.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE ARE PROVIDED “AS IS” WITH ALL
FAULTS. KWIKBIT DISCLAIMS ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF
DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL KWIKBIT OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL
DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OF DAMAGE TO DATA ARISING OUT OF THE USE OR
INABILITY TO USE THIS MANUAL, EVEN IF KWIKBIT HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Version 2.1
©2016-2021 Kwikbit Inc. All rights reserved.
KwikbitTM is a trademark of Kwikbit Inc.
Google and the Google logo are registered trademarks of Google LLC, used with permission.

Edge Controller Guide
Kwikbit Edge Controller Guide 3
Table of Contents
1Overview ------------------------------------------------------------------------------------------------------------5
1.1 Additional documentation ------------------------------------------------------------------------------6
1.2 Additional help----------------------------------------------------------------------------------------------6
2Description of the Kwikbit 60 GHz system---------------------------------------------------------------7
2.1 Edge Controller ---------------------------------------------------------------------------------------------8
2.2 Kwikbit Wireless Devices --------------------------------------------------------------------------------8
3Deployment steps (using an Edge Controller map plan)--------------------------------------------9
3.1 Install Edge Controller and log into it-------------------------------------------------------------- 10
3.2 Security Settings------------------------------------------------------------------------------------------ 13
3.2.1 Upload the Security Certificate ----------------------------------------------------------------13
3.3 Set Identity Description and Cloud information ----------------------------------------------- 14
3.4 Set Networking information--------------------------------------------------------------------------15
3.5 Create a map Plan, install and provision devices----------------------------------------------16
3.6 Review and configure devices -----------------------------------------------------------------------26
3.7 Verify network operations ---------------------------------------------------------------------------- 28
3.8 Adjust Security: Airlink Passcode and SSID ------------------------------------------------------28
4Monitoring-------------------------------------------------------------------------------------------------------- 29
5Network management tasks ------------------------------------------------------------------------------- 31
5.1 Security tasks----------------------------------------------------------------------------------------------31
5.1.1 Set the preferred hub for a remote device------------------------------------------------31
5.1.2 Set the SSID and Airlink Passcode for the network and devices ------------------- 33
5.2 Manage user accounts, permissions and passwords ----------------------------------------34
5.2.1 Add a new user -------------------------------------------------------------------------------------35
5.2.2 Edit a user account --------------------------------------------------------------------------------36
5.2.3 Delete user account-------------------------------------------------------------------------------36
5.3 Access Cloud Account ----------------------------------------------------------------------------------37
5.4 Networking settings-------------------------------------------------------------------------------------37
5.4.1 Configure Interfaces ------------------------------------------------------------------------------ 38

Edge Controller Guide
4 Kwikbit Edge Controller Guide
5.4.2 Gateway Configuration---------------------------------------------------------------------------39
5.4.3 Editing the SMTP Settings to send notifications ----------------------------------------- 40
5.5 Adding, replacing, and removing devices --------------------------------------------------------41
5.5.1 Add a new remote device at a new site, to an existing network ------------------- 41
5.5.2 Add a new hub device to an existing site --------------------------------------------------42
5.5.3 Add a new site: with both Remote and Hub devices ----------------------------------- 44
5.5.4 Pre-configure a device before adding to a secure network--------------------------46
5.5.5 Replace a device with new hardware-------------------------------------------------------- 47
5.5.6 Remove a device from a site -------------------------------------------------------------------47
5.5.7 Remove a site --------------------------------------------------------------------------------------- 47
5.6 Review and adjust settings for a device ----------------------------------------------------------48
6Troubleshooting ------------------------------------------------------------------------------------------------ 49
6.1 Kwikbit RF devices are not found by the Edge Controller after installation ----------49
6.2 Factory reset for devices------------------------------------------------------------------------------- 49
7Appendices-------------------------------------------------------------------------------------------------------50
7.1 Acronyms ---------------------------------------------------------------------------------------------------50
7.2 Terms -------------------------------------------------------------------------------------------------------- 51

Edge Controller Guide
Kwikbit Edge Controller Guide 5
1Overview
Thank you for choosing the Edge Controller from Kwikbit. You are on your way to
automated commissioning and advanced remote network management. You can plan,
install, deploy and manage your network simply and securely with Edge Controller.
This guide is for Network administrators or technicians who are comfortable with both
basic network operations, and their organization’s specific network practices and
operations, but not experienced with Kwikbit Edge Controller. This guide describes the use
of the Kwikbit Edge Controller for the following:
●Initial setup of a 60 GHz network system
●Monitoring a network
●Network management tasks.
Setting up the 60GHz network with Edge Controller
The Initial Setup section offers a general deployment strategy, using K60i devices for the
network examples. Because the Kwikbit system is so flexible, alternate options may also be
presented. Initial Setup tasks include:
●Install the Edge Controller and root device.
●Configure some settings for security, identity, networking, cloud access.
●Create a map plan to interactively layout the network device sites, including planned
links and install Kwikbit devices.
●Install and provision devices.
●Configure devices.
●Verify the network against the plan.
Monitoring
Once initial setup is complete, monitoring the network can be done via on-site access to
the Edge Controller or through the convenience of cloud access to your account.

Edge Controller Guide
6 Kwikbit Edge Controller Guide
Managing
Management tasks include:
●Adding, moving or changing devices
●Replacing devices
●Changes to device roles and plans
●Managing users and permissions.
1.1 Additional documentation
Further information about installing Kwikbit 60 GHz network devices can be found in:
K60 Install Guide
K60c Install Guide
K60i Install Guide
K60x Install Guide
K60 User Guide
K60c User Guide
K60i User Guide
K60x User Guide
1.2 Additional help
Kwikbit is committed to providing our customers with high quality technical support.
Web
support.kwikbit.com
E-mail
[e-mail]
Phone
[phone]

Edge Controller Guide
Kwikbit Edge Controller Guide 7
2Description of the Kwikbit 60 GHz system
Kwikbit networks use a tree topology. The term site refers to a location in the network
where a Kwikbit device or devices are connected. A site may be a place where the network
tree branches out, or it may be a leaf on the network tree. The following diagram shows a
simple network layout with six sites.
Simplified Network Plan
One Kwikbit device (wired-LAN-connected) at the first site in the network tree functions as
the root hub. All devices at the root site take on a hub role(s). One must be assigned the
root hub role.
Additional sites on the network tree will have at least one device set to a remote role. The
leaves of the tree have a single remote device. For sites on the network tree where
branches divide, the remote device can be wired with additional devices. The additional
devices function as hubs which wirelessly connect to additional remote devices at leaf sites
or further branch sites on the network tree.
Wireless communications in the Kwikbit 60GHz system only take place between remotes
and hubs. Wireless links do not occur between two hubs or between two remotes.

Edge Controller Guide
8 Kwikbit Edge Controller Guide
The wireless radio frequency (RF) link between hubs and remotes is shown with red lines in
the diagram above. For each wireless link, the device with the hub role is closer to the root,
than the device with the remote role.
Note: The deployment must take care to avoid the formation of an island, that is, a
device, or set of connected devices, for which there is no path to the wired
LAN (i.e. no path to the root).
Site Survey
A site survey should be completed for your planned network. Consider coverage, capacity,
interference areas, installation requirements, as well as any other issues.
Kwikbit can help with surveying your site, recommending a plan, physical installation,
further configuration and deployment. Contact us for more information.
2.1 Edge Controller
Kwikbit’s Edge Controller offers advanced management for your network, using a
convenient graphical user interface (GUI). The Edge Controller offers tools to help with
quick deployment of multi-gigabit distribution and access networks. Plan and deploy your
network using familiar mapping tools that show interactive coverage and link status. Edge
Controller offers further tools for network device configuration, user management and
network monitoring. Cloud and remote services provide secure access where and when
you need it.
2.2 Kwikbit Wireless Devices
Kwikbit offers a range of wireless devices that operate in the 60 GHz radio frequency range.
See www.kwikbit.com for a description of all devices offered. Some innovative features of
Kwikbit devices include:
●License-free 60GHz spectrum operation
●High capacity, low latency
●Adaptive beamforming antenna
●Carrier-grade construction for outdoor devices.

Edge Controller Guide
Kwikbit Edge Controller Guide 9
3Deployment steps using the Edge Controller
Once your site survey is complete and you have a general network plan, determine how to
proceed based on your circumstances.
●If you are experienced at network installation, or have a Kwikbit site plan or
professional Kwikbit installation, you can install devices in the desired areas, then
plug in Edge Controller to formalize the plan, set security, provision devices and
adjust device configurations as needed to finish deployment of your Kwikbit
network.
●If you are less familiar with Kwikbit devices and their coverage areas, but have a
good working knowledge of your network, we recommend the following steps to
deploy your Kwikbit network.
1. Install the Edge Controller and the root hub device.
2. Log in to the Edge Controller.
3. Upload the Security Certificate (SSL certificate), then adjust Identity and
Networking settings.
4. Use the Edge Controller map plan to plan devices and links. Map plan enables
you to plan and visualize coverage, direction and role selection for devices
before installation, to help you determine suitable installation locations for
devices.
5. Use the resulting plan to install the Kwikbit devices in your network.
6. Provision the installed devices using the map plan you created.
7. Review and set device configurations.
8. Verify your network and adjust desired Security settings with Edge Controller.

Edge Controller Guide
10 Kwikbit Edge Controller Guide
3.1 Install Edge Controller and log into it
The Edge Controller requires a separate network connection to a corporate network or the
Internet for management and support.
1. Connect the Kwikbit device which will serve as the root hub to the Edge
Controller with a Category 5 (or higher) wired connection. A direct connection is
recommended.
Note: A direct connection between the root device and the Edge Controller on
the same local network and subnet simplifies installation and deployment.
In this case, the Edge Controller can locate and connect to Kwikbit devices
directly.
The Edge Controller uses multicast service discovery (mSD) and mDNS
protocols to locate Kwikbit devices.
However, if the Edge Controller cannot connect directly and must
communicate through a router, the root device should be configured as a
gateway hub during set up. See the step on Network information.
2. Connect the power cord to the Kwikbit Edge Controller and plug it in.
3. Connect an ethernet Cat 5e cable (or higher) from the LAN, corporate network,
router or other Internet source to the port labeled Network on the Edge
Controller.
Connects to
LAN
Connects to the
Kwikbit network
Power port
LED indicates
power is on