KYE Systems Corp. Genius SP-i150 User manual

Service Guide SP-i150
SERVICE GUIDE
KYESYSTEMS CORP.
SP-i150
Version : 1.0
Page 1 of 14

Service Guide SP-i150
Version : 1.0
Revision History
Version Date Change
1.0 15/01/2010
Version : 1.0
Page 2 of 14

Service Guide SP-i150
Table of Contents
evision History …………………………………………………………………….2
Table of Contents ……………….……………………………………………………3
Getting Started ……………………………………………………………………….4
Conventions Used in this Guide ……..……………………………………....4
Safety Precautions …….……………………………………………………..4
Chapter 1. How to Handle Defective eturns……………………………………..5
1.1 Overview …………………………………………………………..5
1.2 Problems …………………………………………………………...6
1.2.1 No sound (Line in jack no function) …………..…7
1.2.2 Power LED (indicator) no light……...………....…8
1.2.3 The Li-ION battery can’t charge.…..….………….8
Chapter 2. Specifications …………………………………………………………..9
Chapter 3. Block Diagram ……………………………………………………….10
Chapter 4. Exploded View ……………………………………………………….11
Chapter 5. Part List ………………………………………………………………12
Chapter 6. Schematic Diagram …………………………………………………..13
Chapter 7. Important Notes ………………………………………………………14
7.1 Packing equirement for Sending the PCB Assembly by Post …..14
7.2 Short of Spare Parts while epairing a Speaker System …………14
Version : 1.0
Page 3 of 14

Service Guide SP-i150
Getting Started
Conventions Used in this Guide
Pay Special Attention : Instructions that are important to remember and
may prevent mistakes .
Caution : Information that, if not followed, may result in damage to the
product .
Safety Precautions
The following precautions should be observed in handling the speaker
Described in this guide :
Place the speakers on a flat, level and stable surface.
Do not place the speakers in environments subject to mist, smoke,
vibration, excessive dust, salty or greasy air, or other corrosive gases
and fumes.
Do not drop or jolt the speakers.
Do not allow anything to drop into the subwoofer case through its
ventilator, as it could result in fatal electric shock or fire .
Place the unit far enough from other equipments for good heat
dissipation .
Disconnect the AC power cord from the AC outlet before performing
any maintenance on the speakers .
Do not perform any maintenance with wet hand .
Prevent foreign substances, such as water, other liquids or chemicals ,
From entering the speakers while performing maintenance procedures
on the speakers .
Version : 1.0
Page 4 of 14

Service Guide SP-i150
Chapter . How to Handle Defective Returns
1.1 Overview
eceiving Defective speakers from
Customers
Function NG
__ __
Analyzing possible malfunction
causes
Function NG Deciding & proceeding the
rectification methods
Function OK
eplace necessary defective parts
Function OK
eturn the speakers with proper
repackaging to customers
Version : 1.0
Page 5 of 14

Service Guide SP-i150
1.2 Problems
Item Problem Description
1.2.1 No sound (Line in jack no function)
1.2.2 Power LED (indicator) no light
1.2.3 The Li-ION battery can’t charge
Version : 1.0
Page 6 of 14

Service Guide
SP-i150
Attention
Please follow the numbered sequence marked within parenthesis given in individual Flow
chat, in that this is the best-recommended sequence to rectify the problems.
1.2.1 One or more channels no sound (Line in jack no function)
Problem
No sound
Analyzer and
Identify the Causes
Broken or short circuit
Defective U1,
U4
Speaker cable
dis-connect , JACK1 or
JACK2 defective or
speaker damaged
Solutions
Check solder points on
PCB
Check and eplace
defective IC
e-connect speaker
cable or replace
defective speaker(s)
Version : 1.0
Page 7 of 14

Service Guide SP-i150
1.2.2 Power LED (indicator) no light
Problem
Power LED (indicator) no light
Analyzer and
Identify the Causes
Power switch or LED
defective
Defective
J1
Solutions
e-solder or replace
defective component(s)
1.2.3 The Li-ION Battery can’t charge
Problem
The Li-ION battery can’t
charge
Analyzer and
Identify the Causes
Broken or short circuit
U2 Battery
Solutions Check solder points on PCB Check and eplace defective
components
Version : 1.0
Page 8 of 14

Service Guide SP-i150
Chapter 2. Specifications
NO. Description Unit Specifications
Out Power at THD 0% W
≧
≧≧
≧ .8
2 Sensitivity mV
600 ± 50
3 Freq. Response ( KHz -3dB) Hz 80~20K ± 0%
4 Separation dB
≧
≧≧
≧ 40
5 S/N ratio dB
≧
≧≧
≧ 80
6 Hum & Noise (Vol.: max) mV
≦
≦≦
≦ 2
Version : 1.0
Page 9 of 14

Service Guide SP-i150
Chapter 3. Block Diagram
Audio
—
►
Tone
Control
Volume
Control
—
►
L.CH Speaker
A
Power
i
Ac
in
Conditioner
Version : 1.0
Page 10 of 14

Service Guide SP-i150
Chapter 4. Exploded View
Version : 1.0
Page 11 of 14

Service Guide SP-i150
Chapter 5. Part List
DESCRIPTION Qty UNIT Part No.
RS,ASM,SP-I 50,HOST,BLACK
3 730954 00
RS,ASM,SP-I 50,HOST,WHITE
PC 3 730954 0
Loud Speaker .25" 4 ohm ~2W PC
FSA5 0 2- 402
Rubber Pad(Φ25 X Φ20 X .0T), SP-i 50
PC 54000 5 00
PCBA, SP-i 50 PC
ASL507003-0025
IC, JRC NJM276 PC
IC, T TPA203 D Set RCI203 0 -000
IC, LN,LN2054 PC
BATTERY, SP-i 50 PC FBY508037-0003
FANNEL BAG SP-i 50 PC 2290076 00
S/N LABEL SP-i150
2 PC 206 0 7 00
CARD SP-i 50 / B 2020 94 0
CARD SP-i 50 / W
PC
2020 93 00
INNER TRAY SP-i 50 PC 2 50288 00
PET BOX, SP-i 50 PC 2 40002 00
Anti-fake Label ( on Gift Box ) PC 206 993 00
No.
2
3
4
5
6
7
8
9
0
2
3
4
5
6
7
Carton, SP-i 50 /50 PC 2 00468 00
Version : 1.0
Page 12 of 14

Service Guide SP-i150
Chapter 6. Schematic Diagram
Pls refer to next page
Version : 1.0
Page 13 of 14

1 2 3 4
A
B
C
D
4
321
D
C
B
ATitle
Number RevisionSize
A4
Date: 21-Jan-2010 Sheet of
File: E:\MODEL INFO\KYE\F4\Mr Pai.ddb Drawn By:
VER090820
S1
SPK
R13
8K2
R8
8K2
C12
104
Vcc
C11
10uF
C5
471
C1
10uF
R5
240k
R4
68k
Shut_DN
1
2
3
4
5
J1
CN4P-USB L1
BEAD120
5V
R11
4.7K
C3
100uF
C2
104
CHRG
1
GND
2
BAT 3
PROG 5
Vcc 4
U2
R10
2K
LD1
RED
BT1
BATTERY
LN2054
Vcc
S1
SW-SPDT
USB ON
BAT ON
C13
151
R12
2K
LD2
BLUE
R9
BEAD120
Q1
NC
C14
NC
SP-i150
C20
224
C17
224
C18
223
C23
224
GND
V+ 1
Out1 2
IN1 3
INT 4
SW
7
IN2
8
OUT2
9
GND
10
Vref 5
Sense
6
U4
IC-NJM2761
GNDGND
R7
3.6k
C16
151
C19
224
C22
105
C21
105
Vcc
GND
C7
471
R1
68k
R3
240k
R2
1k
C8
270P
C10
270P
C9
270P
R6
100K
VDD
B1
IN-
C1
IN+
A1
ShutDN
C2 GND B3
Vo- A3
Vo+ C3
PVDD B2
GND
A2
U1
TPA2031D1
So-
So+
L2
BEAD120
L3
BEAD120
C4
473
C6
473

Service Guide SP-i150
Chapter 7. Important Notes
7.1 Packing equirement for Sending the PCB Assembly by Post
PCB assembly is a kind of sophisticated electronic circuit board. Well
packing will be required when sending them by post.
* Some sophisticated IC components are mounted on the PCB assembly,
hence it is necessary to pack each PCB assembly with a separate static
protecting bag, in order to avoid static electricity.
* eliable external packing is also very important when sending PCB
assembly by post, in that it would avoid unnecessarily lost or damage.
7.2 Short of Spare Parts while epairing a Speaker System
If you are short of spare parts when you have some speaker systems waiting
to be repaired, it would be recommended to take the necessary parts form
one speaker system, so that you may have the as many speaker systems.
Version : 1.0
Page 14 of 14