KYLAND SICOM3000A-LITE Assembly instructions

SICOM3000A-LITE Industrial Ethernet Switch
Hardware Installation Manual
Publication Data: Mar. 2019
Version: V1.0
No.: 112020174

SICOM3000A-LITE Industrial Ethernet Switch
Hardware Installation Manual
Disclaimer: Kyland Technology Co., Ltd. tries to keep the content of this manual as
accurate and as updated as possible. This document is not guaranteed to be error-free, and
we reserve the right to amend it without notice to users.
All rights reserved.
No part of this documentation may be excerpted, reproduced, translated, annotated or
duplicated, in any form or by any means without the prior written permission of KYLAND
Corporation.
Copyright © 2019 Kyland Technology Co., Ltd.

Notice for Safety Operation
The product performs reliably as long as it is used according to the guidance. Artificial
damage or destruction of the device should be avoided. Before using the device, read this
manual carefully for personal and equipment safety. Please keep the manual for further
reference. Kyland is not liable to any personal or equipment damage caused by violation of
this notice.
Do not place the device near water sources or damp areas. Keep the ambient relative
humidity within the range from 5% to 95% (non-condensing).
Do not place the device in an environment with high magnetic field, strong shock, or high
temperature. Keep the working and storage temperatures within the allowed range.
Install and place the device securely and firmly.
Please keep the device clean; if necessary, wipe it with a soft cotton cloth.
Do not place any irrelevant materials on the device or cables. Ensure adequate heat
dissipation and tidy cable layout without knots.
Wear antistatic gloves or take other protective measures when operating the device.
Avoid any exposed metal wires because they may be oxidized or electrified.
Install the device in accordance with related national and local regulations.
Before power-on, make sure the power supply is within the allowed range of the device.
High voltage may damage the device.
Power connectors and other connectors should be firmly interconnected.
Do not plug in or out the power supply with wet hands. When the device is powered on,
do not touch the device or any parts with wet hands.
Before operating a device connected to a power cable, remove all jewelry (such as rings,
bracelets, watches, and necklaces) or any other metal objects, because they may cause
electric shock or burns.
Do not operate the device or connect or disconnect cables during an electrical storm.
Use compatible connectors and cables. If you are not sure, contact our sales or
technical support personnel for confirmation.

Do not disassemble the device by yourself. When an anomaly occurs, contact our sales
or technical support personnel.
If any part is lost, contact our sales or technical support personnel to purchase the
substitute. Do not purchase parts from other channels.
Dispose of the device in accordance with relevant national provisions, preventing
environmental pollution.
In the following cases, please immediately shut down your power supply and contact your
Kyland representative:
Water gets into the equipment.
Equipment damage or shell damage.
Equipment operation or performance has abnormally changed.
The equipment emits odor, smoke or abnormal noise.
The following information applies when operating this device in hazardous locations:
Suitable for use in Class I, Division 2, Groups A, B, C and D Hazardous Locations, or
nonhazardous locations only.
Cet appareillage est utilisable dans les emplacements de Classe I, Division 2, Groupes A, B,
C et D, ou dans les emplacements non dangereux seulement.
WARNING: EXPLOSION HAZARD
Do not disconnect equipment while the circuit is live or unless the area is known to be
free of ignitable concentrations.
Substitution of any component may impair suitability for Class I, Division 2.
AVERTISSEMENT: RISQUE D'EXPLOSION
Avant de deconnecter l'equipement, couper le courant ou s'assurer que l'emplacement
est designe non dangereux.
La substitution de composants peut rendre ce materiel inacceptable pour les
emplacements de Classe I, Division 2.

NOTE: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.

I
Contents
1 Product Overview...............................................................................................................1
1.1 Mini Products ...............................................................................................................1
2 Structure and Interface.......................................................................................................3
2.1 Front Panel ..................................................................................................................3
2.2 Top Panel.....................................................................................................................4
3 Mounting.............................................................................................................................5
3.1 Dimension Drawing......................................................................................................5
3.2 Mounting Modes and Steps .........................................................................................6
3.2.1 DIN-Rail Mounting.................................................................................................6
3.2.2 Panel Mounting......................................................................................................7
4 Connection .......................................................................................................................10
4.1 10/100Base-T(X) Ethernet Port..................................................................................10
4.2 10/100/1000Base-T(X) Ethernet Port...............................................错误!未定义书签。
4.3 100Base-FX Ethernet Port.........................................................................................11
4.4 100/1000Base-X, 10/100/1000Base-T(X) SFP slot....................................................12
4.4.1 SFP Optical Module.............................................................................................13
4.4.2 SFP Electrical Module .........................................................................................14
4.5 Console Port ..............................................................................................................15
4.5.1 MIni usb...............................................................................................................15
4.6 Grounding..................................................................................................................16
4.7 Power Terminal Block................................................................................................16
4.8 Alarm Terminal Block.................................................................................................18
5 Reset................................................................................................................................20
6 LEDs.................................................................................................................................21
7 Switch Access ..................................................................................................................22
7.1 Access through Console Port.....................................................................................22
7.2 Access through Telnet ...............................................................................................24

II
7.3 Access through Web..................................................................................................25
8 Basic Features and Specifications....................................................................................26

Product Overview
1
1 Product Overview
SICOM3000A-LITE includes a series of green low-consumption industrial Ethernet switches
applicable to wind power, distribution network automation, subway PIS, power SCADA,
petroleum and petrochemical, actory automation, intelligent transportation, rail transit, and
many other industries. The switch complies with the Railway Signal Data Security Network
Specifications V3.0 oriented towards the railway system.
The series switches provide Mini USB Console port, and supports one-touch recovery, and
network management through Web, Telnet, and console port.
SICOM3000A-LITE supports DIN rail mounting and panel mounting. It provides two
100/1000Base-X, 10/100/1000Base-T(X) SFP slots (Gigabit SFP Slot), and eight
10/100Base-T(X) Ethernet ports, The SPF slots support the optical power detection function.
For details, see the following table.
1.1 Mini Products
Table 1 Models
Models
SICOM3000A-LITE-Ports-Connector-PS1-PS2
Code definition
Code option
Ports: GX, S/M, T
2GX8T, 1S4T, 1M4T, 2S4T,2M4T,2S6T,2M6T, 8T, 6T
Note:
2GX8T: two 100/1000Base-X, 10/100/1000Base-T(X) SFP slots; eight
10/100Base-T(X) ports
1S4T: one 100Base-FX ports, single mode; four 10/100Base-T(X) ports.
1M4T: one 100Base-FX ports, multiple mode; four 10/100Base-T(X) ports
2S4T: two 100Base-FX ports, single mode; four 10/100Base-T(X) ports
2M4T: two 100Base-FX ports, multiple mode; four 10/100Base-T(X) ports
2S6T: two 100Base-FX ports, single mode; six 10/100Base-T(X) ports
2M6T: two 100Base-FX ports, multiple mode; six 10/100Base-T(X) ports

Product Overview
2
8T: eight 10/100Base-T(X) ports
6T: six 10/100Base-T(X) ports
Connector: parameters for
S/M
Ports with M:
SC05=SC connector, 1310nm, 5km
ST05=ST connector, 1310nm, 5km
FC05=FC connector, 1310nm, 5km
Ports with S:
SC40=SC connector, 1310nm, 40km
ST40=ST connector, 1310nm, 40km
FC40=FC connector, 1310nm, 40km
SC60=SC connector, 1310nm, 60km
SC80=SC connector, 1550nm, 80km
Ports without S or M:
N/A
PS1-PS2: power input
L2-L2 (24-48VDC, redundant power input)
L5-L5 (12-24VDC, redundant power input)
Note：
For the product information listed in these tables, we reserve the right to amend it without notice.
To obtain the latest information, you can contact our sales or technical support personnel.

Structure and Interface
3
2 Structure and Interface
Caution:
It is recommended to purchase the port dustproof shield (optional) to keep ports clean and
ensure device performance.
2.1 Front Panel
Figure 1 Front Panel
(1) Power 1 LED
(2) Power 2 LED
(3) Running LED
(4) Ring LED
(5) Alarm LED
(6) 100Base-FX Ethernet port connection status LED
(7) Gigabit SFP Slot connection status LED
(8) Reset button
(9) Console port
(10) 10/100Base-T(X) Ethernet Port
(11) 10/100Base-T(X) Ethernet port speed LED (yellow)
(12) 10/100Base-T(X) Ethernet Port connection status LED (green)
(13) 100Base-FX Ethernet port
(14) Gigabit SFP Slot

Structure and Interface
4
2.2 Top Panel
Figure 2 Top Panel

Mounting
5
3 Mounting
3.1 Dimension Drawing
Figure 3 Dimensions for DIN-Rail Mounting (unit: mm)
Figure 4 Dimensions for DIN-Rail Mounting (unit: mm)

Mounting
6
Caution:
As part of the heat dissipation system, the switch housing becomes hot during operation.
Please use caution when coming in contact and avoid covering the switch housing when the
switch is running.
The figures in this manual are only for reference.
3.2 Mounting Modes and Steps
The device supports both DIN-rail mounting and panel mounting. Before installation, make
sure that the following requirements are met.
1) Environment: temperature (-40℃to 75℃), ambient relative humidity (5% to 95%,
non-condensing)
2) Power requirement: The power input is within the voltage range of the switch.
3) Grounding resistance: <5
4) No direct sunlight, distant from heat source and areas with strong electromagnetic
interference.
5) Devices are to be installed in an authority certified enclosure and accessible only by the
use of a tool.
6) Devices should be installed and accessed by service personnel or users who have been
instructed about the reasons for the restrictions applied to the location and about any
precautions that shall be taken.
3.2.1 DIN-Rail Mounting
DIN-Rail Mounting
Step 1: Select the mounting position for the device and guarantee adequate space and heat
dissipation.
Step 2: Insert the connecting seat onto the top of the DIN rail, and push the bottom of the
device inward and upward to ensure the DIN rail fits in the connecting seat. Make sure the
device is firmly installed on the DIN rail, as shown in the following figure.

Mounting
7
Figure 5 DIN-Rail Mounting
DIN-Rail Dismounting
Step 1: As shown in the following figure, press the device downward and move the device in
direction 1 until the bottom of the device is detached from the DIN rail.
Step 2: Pull the device upward and move the device in direction 2 until the device is removed
from the DIN rail completely.
Figure 6 DIN-Rail Dismounting
3.2.2 Panel Mounting
Note:
To adopt panel mounting, you need to purchase the plate for panel mounting (optional).
Mounting

Mounting
8
Step 1: Use screws to fix the plate for panel mounting to the rear panel of the device.
Step 2: Select the mounting position (on a wall or inner wall of a cabinet) for the device and
guarantee adequate space and heat dissipation for it.
Step 3: Punch four holes in the selected position according to the dimensions for panel
mounting. Insert four screws into the four holes respectively, and turn the screws with a
screwdriver until about a 5mm distance is left between each screw head and the wall.
Step 4: Align the four mounting holes on the plate for panel mounting with the four screws.
Make the screws pass through the Ф6.5 positions in the following figure. Move the device in
direction 1 until the four screws are in the Ф4 positions. Then tighten the screws to complete
mounting.
Figure 7 Panel Mounting
Dismounting
Step 1: Loosen the four screws with a screwdriver. Move the device upward until the four
screws are in the Ф6.5 positions in the following figure. Then remove the plate for panel
mounting from the four screws to detach the device from the wall or inner wall of the cabinet.
Step 2: Loosen the screws completely with a screwdriver. Remove them from the wall or
inner wall of the cabinet. Then remove the plate for panel mounting from the rear panel to
complete dismounting the device.

Mounting
9
Figure 8 Panel Dismounting
Caution:
Cut off the power and disconnect all cables before mounting, dismounting or moving the
equipment.

Connection
10
4 Connection
4.1 10/100Base-T(X) Ethernet Port
10/100Base-T(X) Ethernet port is equipped with RJ45 connector. The port is self-adaptive. It
can automatically configure itself to work in 10M or 100M state, full or half duplex mode. The
port can also adapt to MDI or MDI-X connection automatically. You can connect the port to a
terminal or network device with a straight-through or cross-over cable.
Pin Definition
Figure 9 RJ45 Port
Table 2 Pin Definitions of 10/100Base-T(X) Ethernet Port
Pin
MDI-X Signal
MDI Signal
1
Receive Data+ (RD+)
Transmit Data+ (TD+)
2
Receive Data- (RD-)
Transmit Data- (TD-)
3
Transmit Data+ (TD+)
Receive Data+ (RD+)
6
Transmit Data- (TD-)
Receive Data- (RD-)
4, 5, 7, 8
Unused
Unused
Note:
"+" and "-" indicate level polarities.
Wiring Sequence

Connection
11
Figure 10 Connection Using Straight-through/Cross-over Cable
Note：
The color of the cable for RJ45 connector meets the 568B standard: 1-orange and white,
2-orange, 3-green and white, 4-blue, 5-blue and white, 6-green, 7-brown and white, and
8-brown.
4.2 100Base-FX Ethernet Port
100Base-FX Ethernet port is equipped with FC/ST/SC connector, and each port consists of
TX (transmit) port and RX (receive) port. To enable data transmission between Device A and
Device B, connect the TX port of Device A to the RX port of Device B, and the RX port of
Device A to the TX port of Device B. The following uses an SC port as an example. The
wiring sequence of an ST/FC port is the same with that of the SC port.
Figure 11 Connection of 100Base-FX Ethernet Port
Caution:
The device uses laser to transmit signals in fibers. The laser meets the requirements of level 1

Connection
12
laser products. Routine operation is not harmful to your eyes, but do not look directly at the fiber
port when the device is powered on.
4.3 100/1000Base-X, 10/100/1000Base-T(X) SFP slot
100/1000Base-X, 10/100/1000Base-T(X) SFP slot (gigabit SFP slot) requires an SFP
optical/electrical module to enable data transmission. The following table lists the SFP
optical/electrical modules (optional) supported by the series switches.
Table 3 SFP Optical/Electrical Modules
Model
Port
MM/SM
Connector
Central
Wavelength
Transmission
Distance
IGSFP-M-SX-LC-850-0.55
1000Base-X port
MM
LC
850nm
0.55km
IGSFP-S-LX-LC-1310-10
1000Base-X port
SM
LC
1310nm
10km
IGSFP-S-LH-LC-1310-40
1000Base-X port
SM
LC
1310nm
40km
IGSFP-S-ZX-LC-1550-80
1000Base-X port
SM
LC
1550nm
80km
IFSFP-M-LX-LC-1310-2
100Base-X port
MM
LC
1310nm
2km
IFSFP-S-LH-LC-1310-40
100Base-X port
SM
LC
1310nm
40km
IGSFP-10/100/1000BASE-
T-RJ45
10/100/1000Base-
T(X) port
--
RJ45
--
--
Note:
The device uses the SFP module that supports digital diagnosis to support the optical power
detection function of the SFP slot. For details about the SFP module, consult our sales or
technical support personnel.

Connection
13
4.3.1 SFP Optical Module
Figure 12 SFP Optical Module
An SFP optical module is equipped with LC connector, and each port consists of a TX
(transmit) port and an RX (receive) port. To enable communication between Device A and
Device B, connect the TX port of Device A to the RX port of Device B, and the RX port of
Device A to the TX port of Device B, as shown in the following figure.
Figure 13 Fiber Connection of an SFP Optical Module
How to Connect the SFP Optical Module
Insert the SFP optical module into the SFP slot in the switch, and then insert the fibers into
the TX port and RX port of the SFP module.
Figure 14 Connecting the SFP Optical Module
Identify the RX port and TX port of an SFP optical module:
1. Insert the two connectors in one end of two fibers into the SFP module, and those in the
other end into the peer module.
2. View the corresponding connection status LED: