Kyocera Copystar CS 3011i User manual

SERVICE
MANUAL
Published in September 2016
2RHSM1
Rev.1
&6 3011i
&6 3511i

CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE
OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
It may be illegal to dispose of this battery into the municipal waste stream. Check with your
local solid waste officials for details in your area for proper disposal.
ATTENTION
IL Y A UN RISQUE D’EXPLOSION SI LA BATTERIE EST REMPLACEE PAR UN MODELE
DE TYPE INCORRECT. METTRE AU REBUT LES BATTERIES UTILISEES SELON LES
INSTRUCTIONS DONNEES.
Il peut être illégal de jeter les batteries dans des eaux d’égout municipales. Vérifiez avec les
fonctionnaires municipaux de votre région pour les détails concernant des déchets solides
et une mise au rebut appropriée.
Notation of products in the manual
For the purpose of this service manual, products are identified by print speed at A4 and black and white
modes.
TASKalfa 3011i : 30 ppm model
TASKalfa 3511i : 35 ppm model

Revision history
Revision Date Pages Revised contents
1 26 August 2016 CONTENTS Chenge: Item and Page number
1-2-10 Correction: Representation of procedure
1-2-23 Change: Add the connector holder
1-3-15, 1-3-17 Correction: Option Description Modify (hard disk added)
1-3-33 Correction: Change the description of switch in U031
1-3-181 Correction: U671 (DIMM →STORAGE)
1-5-57, 1-5-58 Correction: Notes when replacing the main PWB
1-5-63 Added: Notes when replacing the engine PWB
1-5-77 to 79 Added: Detaching and reattaching the SSD

This page is intentionally left blank.

Safety precautions
This booklet provides safety warnings and precautions for our service personnel to ensure the safety of
their customers, their machines as well as themselves during maintenance activities. Service personnel
are advised to read this booklet carefully to familiarize themselves with the warnings and precautions
described here before engaging in maintenance activities.

Safety warnings and precautions
Various symbols are used to protect our service personnel and customers from physical danger and
to prevent damage to their property. These symbols are described below:
DANGER: High risk of serious bodily injury or death may result from insufficient attention to or incorrect
compliance with warning messages using this symbol.
WARNING: Serious bodily injury or death may result from insufficient attention to or incorrect compliance
with warning messages using this symbol.
CAUTION: Bodily injury or damage to property may result from insufficient attention to or incorrect com-
pliance with warning messages using this symbol.
Symbols
The triangle ( ) symbol indicates a warning including danger and caution. The specific point of attention is
shown inside the symbol.
General warning. Warning of risk of electric shock.
Warning of high temperature.
indicates a prohibited action. The specific prohibition is shown inside the symbol.
General prohibited action. Disassembly prohibited.
indicates that action is required. The specific action required is shown inside the symbol.
General action required. Remove the power plug from the wall outlet.
Always ground the copier.

1. Installation Precautions
WARNING
• Do not use a power supply with a voltage other than that specified. Avoid multiple connections to
one outlet: they may cause fire or electric shock. When using an extension cable, always check that
it is adequate for the rated current. .....................................................................................................
• Connect the ground wire to a suitable grounding point. Not grounding the copier may cause fire or
electric shock. Connecting the earth wire to an object not approved for the purpose may cause
explosion or electric shock. Never connect the ground cable to any of the following: gas pipes, light-
ning rods, ground cables for telephone lines and water pipes or faucets not approved by the proper
authorities. ..........................................................................................................................................
CAUTION:
• Do not place the copier on an infirm or angled surface: the copier may tip over, causing injury. .........
• Do not install the copier in a humid or dusty place. This may cause fire or electric shock. .................
• Do not install the copier near a radiator, heater, other heat source or near flammable material. This
may cause fire. ...................................................................................................................................
• Allow sufficient space around the copier to allow the ventilation grills to keep the machine as cool
as possible. Insufficient ventilation may cause heat buildup and poor copying performance. ............
• Always handle the machine by the correct locations when moving it. .................................................
• Always use anti-toppling and locking devices on copiers so equipped. Failure to do this may cause
the copier to move unexpectedly or topple, leading to injury. ..............................................................
• Avoid inhaling toner or developer excessively. Protect the eyes. If toner or developer is accidentally
ingested, drink a lot of water to dilute it in the stomach and obtain medical attention immediately.
If it gets into the eyes, rinse immediately with copious amounts of water and obtain medical atten-
tion. .....................................................................................................................................................
• Advice customers that they must always follow the safety warnings and precautions in the copier’s
instruction handbook. .........................................................................................................................

2. Precautions for Maintenance
WARNING
• Always remove the power plug from the wall outlet before starting machine disassembly. ................
• Always follow the procedures for maintenance described in the service manual and other related
brochures. ..........................................................................................................................................
• Under no circumstances attempt to bypass or disable safety features including safety mechanisms
and protective circuits. ........................................................................................................................
• Always use parts having the correct specifications. ............................................................................
• Always use the thermostat or thermal fuse specified in the service manual or other related brochure
when replacing them. Using a piece of wire, for example, could lead to fire or other serious acci-
dent. ...................................................................................................................................................
• When the service manual or other serious brochure specifies a distance or gap for installation of a
part, always use the correct scale and measure carefully. ..................................................................
• Always check that the copier is correctly connected to an outlet with a ground connection. ...............
• Check that the power cable covering is free of damage. Check that the power plug is dust-free. If it
is dirty, clean it to remove the risk of fire or electric shock. .................................................................
• Never attempt to disassemble the optical unit in machines using lasers. Leaking laser light may
damage eyesight. ...............................................................................................................................
• Handle the charger sections with care. They are charged to high potentials and may cause electric
shock if handled improperly. ...............................................................................................................
CAUTION
• Wear safe clothing. If wearing loose clothing or accessories such as ties, make sure they are safely
secured so they will not be caught in rotating sections. ......................................................................
• Use utmost caution when working on a powered machine. Keep away from chains and belts. ..........
• Handle the fixing section with care to avoid burns as it can be extremely hot. ..................................
• Check that the fixing unit thermistor, heat and press rollers are clean. Dirt on them can cause
abnormally high temperatures. ...........................................................................................................

• Do not remove the ozone filter, if any, from the copier except for routine replacement. ......................
• Do not pull on the AC power cord or connector wires on high-voltage components when removing
them; always hold the plug itself. ........................................................................................................
• Do not route the power cable where it may be stood on or trapped. If necessary, protect it with a
cable cover or other appropriate item. ................................................................................................
• Treat the ends of the wire carefully when installing a new charger wire to avoid electric leaks. ..........
• Remove toner completely from electronic components. .....................................................................
• Run wire harnesses carefully so that wires will not be trapped or damaged. ......................................
• After maintenance, always check that all the parts, screws, connectors and wires that were
removed, have been refitted correctly. Special attention should be paid to any forgotten connector,
trapped wire and missing screws. .......................................................................................................
• Check that all the caution labels that should be present on the machine according to the instruction
handbook are clean and not peeling. Replace with new ones if necessary. .......................................
• Handle greases and solvents with care by following the instructions below: ......................................
· Use only a small amount of solvent at a time, being careful not to spill. Wipe spills off completely.
· Ventilate the room well while using grease or solvents.
· Allow applied solvents to evaporate completely before refitting the covers or turning the power
switch on.
· Always wash hands afterwards.
• Never dispose of toner or toner bottles in fire. Toner may cause sparks when exposed directly to
fire in a furnace, etc. ...........................................................................................................................
• Should smoke be seen coming from the copier, remove the power plug from the wall outlet immedi-
ately. ...................................................................................................................................................
3. Miscellaneous
WARNING
• Never attempt to heat the drum or expose it to any organic solvents such as alcohol, other than the
specified refiner; it may generate toxic gas. ........................................................................................
• Keep the machine away from flammable liquids, gases, and aerosols. A fire or an electric shock
might occur. ........................................................................................................................................

This page is intentionally left blank.

2RG/2RH
CONTENTS
1-1 Specifications
1-1-1 Specifications ........................................................................................................................1-1-1
1-1-2 Part Names............................................................................................................................1-1-9
(1) The main unit(Front side) .................................................................................................1-1-9
(2) The main unit(Rear side)................................................................................................1-1-11
(3) Operation Panel..............................................................................................................1-1-12
1-1-3 Machine sectional plan........................................................................................................1-1-13
1-2 Installation
1-2-1 Installation environment.........................................................................................................1-2-1
1-2-2 Unpacking and setting of the machine ..................................................................................1-2-2
(1) Installation procedures .....................................................................................................1-2-2
(2) Default setting of the copy mode....................................................................................1-2-13
1-2-3 Optional configuration..........................................................................................................1-2-14
1-2-4 Installing the optional equipment.........................................................................................1-2-16
(1) SD/SDHC memory card .................................................................................................1-2-16
(2) Hard Disk (HD-12): KDA standard..................................................................................1-2-17
(3) Installation of attaching Gigabit Ethernet extension kit...................................................1-2-20
(4) Wireless LAN interface installation.................................................................................1-2-20
(5) Wireless LAN interface (IB-35).......................................................................................1-2-22
(6) Document table (DT-730(B)) ..........................................................................................1-2-24
(7) Numeric Keypad (NK-7100 / NK-7110)..........................................................................1-2-27
(8) USB keyboard (Except 100V model)..............................................................................1-2-30
(9) Coin Vendor installation(100V model only) ....................................................................1-2-35
(10) card reader installation ..................................................................................................1-2-38
(11) Handset attaching...........................................................................................................1-2-41
(11-1) When attaching the main unit directly ...................................................................1-2-41
(11-2) In case installing the document table....................................................................1-2-45
1-2-5 About Optional Applications ................................................................................................1-2-54
1-2-6 Initializing procedures after installing the FAX system ........................................................1-2-55
1-3 Maintenance mode
1-3-1 Maintenance mode................................................................................................................1-3-1
(1) Executing the maintenance mode....................................................................................1-3-1
(2) Maintenance modes list ...................................................................................................1-3-2
(2-1) Content of each maintenance mode .......................................................................1-3-8
1-4 Troubleshooting
1-4-1 Paper misfeed detection........................................................................................................1-4-1
(1) Paper misfeed indication ..................................................................................................1-4-1
(2) Paper misfeed detection component................................................................................1-4-2
1-4-2 Self-diagnostic function .......................................................................................................1-4-12
(1) Self-diagnostic function ..................................................................................................1-4-12
(2) Self diagnostic codes......................................................................................................1-4-12
1-4-3 Image formation problems...................................................................................................1-4-69
(1) No image appears (entirely white)..................................................................................1-4-70
(2) No image appears (entirely black)..................................................................................1-4-71
(3) Image is too light. ...........................................................................................................1-4-71
(4) The background is colored. ............................................................................................1-4-72
(5) White streaks are printed vertically.................................................................................1-4-72

2RG/2RH
(6) Black streaks are printed vertically.................................................................................1-4-72
(7) Streaks are printed horizontally......................................................................................1-4-73
(8) A part of image is dark or light........................................................................................1-4-73
(9) Spots are printed............................................................................................................1-4-73
(10) Image is blurred..............................................................................................................1-4-74
(11) The leading edge of the image is consistently misaligned with the original. ..................1-4-74
(12) The leading edge of the image is sporadically misaligned with the original...................1-4-74
(13) Paper is wrinkled............................................................................................................1-4-74
(14) Offset occurs. .................................................................................................................1-4-75
(15) Part of image is missing. ................................................................................................1-4-75
(16) Fusing is loose................................................................................................................1-4-75
(17) Image is out of focus. .....................................................................................................1-4-75
(18) Image center does not align with the original center. .....................................................1-4-76
1-4-4 Electric problems.................................................................................................................1-4-77
1-4-5 Mechanical problems...........................................................................................................1-4-81
1-4-6 Send error code...................................................................................................................1-4-82
(1) Scan to SMB error codes ...............................................................................................1-4-82
(2) Scan to FTP error codes ................................................................................................1-4-83
(3) Scan to E-mail error codes.............................................................................................1-4-85
1-4-7 Error codes..........................................................................................................................1-4-87
(1) Error code.......................................................................................................................1-4-87
(2) Table of general classification........................................................................................1-4-88
(2-1) U004XX error code table: Interrupted phase B .....................................................1-4-91
(2-2) U006XX error code table: Problems with the unit .................................................1-4-92
(2-3) U008XX error code table: Page transmission error...............................................1-4-92
(2-4) U009XX error code table: Page reception error....................................................1-4-92
(2-5) U010XX error code table: G3 transmission...........................................................1-4-93
(2-6) U011XX error code table: G3 reception ................................................................1-4-95
(2-7) U017XX error code table: V.34 transmission........................................................1-4-96
(2-8) U018XX error code table: V.34 reception..............................................................1-4-97
(2-9) U023XX error code table: Relay command abnormal reception...........................1-4-97
(2-10) U044XX error code table: Encrypted transmission ...............................................1-4-97
1-5 Assembly and disassembly
1-5-1 Precautions for assembly and disassembly...........................................................................1-5-1
(1) Precautions.......................................................................................................................1-5-1
(2) Storage and handling of the drum....................................................................................1-5-1
(3) Storage of the toner container..........................................................................................1-5-1
(4) How to tell a genuine Kyocera toner container.................................................................1-5-2
1-5-2 OUTER COVERS..................................................................................................................1-5-3
(1) Detaching and attaching the front cover...........................................................................1-5-3
(2) Detaching and attaching the rear upper cover .................................................................1-5-5
(3) Detaching and attaching the rear lower cover..................................................................1-5-5
(4) Detaching and attaching the inner tray.............................................................................1-5-6
(5) Detaching and attaching the front upper cover.................................................................1-5-8
(6) Detaching and attaching the eject rear cover...................................................................1-5-9
(7) Detaching and refitting the eject rear cover......................................................................1-5-9
1-5-3 Paper feed section...............................................................................................................1-5-10
(1) Detaching and attaching the primary paper feed unit.....................................................1-5-10
(2) Detaching and attaching the MP paper feed roller and MP separation pad...................1-5-11
(3) Detaching and attaching the registration cleaner...........................................................1-5-13
(4) Detaching and attaching the MP tray .............................................................................1-5-16

2RG/2RH-1
1-5-4 Developer section................................................................................................................1-5-18
(1) Detaching and reattaching the developer unit................................................................1-5-18
1-5-5 Drum section .......................................................................................................................1-5-21
(1) Detaching and reattaching the drum unit........................................................................1-5-21
(2) Detaching and attaching the charger roller unit..............................................................1-5-23
1-5-6 Transfer/separation section.................................................................................................1-5-24
(1) Detaching and attaching the transfer roller unit..............................................................1-5-24
1-5-7 Fuser section.......................................................................................................................1-5-25
(1) Detaching and attaching the fuser unit...........................................................................1-5-25
1-5-8 Drive section........................................................................................................................1-5-26
(1) Detaching and attaching the drive unit 1........................................................................1-5-26
(2) Detaching and attaching the drive unit 2........................................................................1-5-28
1-5-9 Optical section.....................................................................................................................1-5-30
(1) Detaching and attaching the Laser Scanner Unit (LSU).................................................1-5-30
(2) Detaching and attaching the image scanner unit ...........................................................1-5-34
(3) Detaching and attaching the LED unit............................................................................1-5-37
(4) Detaching and reattaching the scanner wires ................................................................1-5-40
(4-1) Detaching the scanner wires.................................................................................1-5-40
(4-2) Fitting the scanner wires .......................................................................................1-5-51
1-5-10 PWBs...................................................................................................................................1-5-54
(1) Detaching and reattaching the main PWB......................................................................1-5-54
(1-1) Notes when replacing the main PWB....................................................................1-5-57
(2) Detaching and reattaching the engine PWB...................................................................1-5-59
(2-1) Notes when replacing the engine PWB.................................................................1-5-63
(3) Detaching and reattaching the power source PWB........................................................1-5-64
(4) Detaching and reattaching the high voltage PWB..........................................................1-5-66
(5) Detaching and reattaching the operation panel PWB 1..................................................1-5-70
1-5-11 Others..................................................................................................................................1-5-77
(1) Detaching and reattaching the SSD ...............................................................................1-5-77
(2) Detaching and reattaching the conveying unit................................................................1-5-80
(3) Direction of installing the principal fan motors................................................................1-5-83
1-6 Firmware
1-6-1 Firmware update....................................................................................................................1-6-1
2-1 Mechanical Construction
2-1-1 Paper feed/conveying section ...............................................................................................2-1-1
(1) Cassette paper feed section.............................................................................................2-1-1
(2) MP tray paper feed section...............................................................................................2-1-3
(3) Conveying section............................................................................................................2-1-4
2-1-2 Drum section .........................................................................................................................2-1-5
2-1-3 Developing section ................................................................................................................2-1-7
2-1-4 Optical section.......................................................................................................................2-1-9
(1) Image scanner section .....................................................................................................2-1-9
(2) Laser scanner section ....................................................................................................2-1-11
2-1-5 Transfer/Separation section ................................................................................................2-1-12
2-1-6 Fuser section.......................................................................................................................2-1-13
2-1-7 Eject/Feedshift section ........................................................................................................2-1-15
2-1-8 Duplex conveying section....................................................................................................2-1-17

2RG/2RH
2-2 Electrical Parts Layout
2-2-1 Electrical parts layout ............................................................................................................2-2-1
(1) PWBs................................................................................................................................2-2-1
(2) Switches and sensors.......................................................................................................2-2-3
(3) Others...............................................................................................................................2-2-6
2-3 PWBs
2-3-1 Main PWB..............................................................................................................................2-3-1
2-3-2 Engine PWB ........................................................................................................................2-3-11
2-3-3 Operation panel PWB 1.......................................................................................................2-3-27
2-3-4 Power supply PWB..............................................................................................................2-3-33
2-4 Appendixes
2-4-1 Appendixes............................................................................................................................2-4-1
(1) List of maintenance parts .................................................................................................2-4-1
(2) Maintenance kits...............................................................................................................2-4-2
(3) Periodic maintenance procedures....................................................................................2-4-3
(4) Repetitive defects gauge..................................................................................................2-4-6
(5) Firmware environment commands ...................................................................................2-4-7
(6) System Error (Fxxxx) Outline .........................................................................................2-4-18
(7) Chart of image adjustment procedures ..........................................................................2-4-25
(8) Wiring diagram ...............................................................................................................2-4-28
Installation Guide
DP-7100 / (Document processor)
DP-7110 / (Document processor)
DP-7120 / (Document processor)
PF-791 / (500 x 2 Paper feeder)
PF-810 / (3000-sheet deck)
DF-791 / (3000-sheet finisher)
DF-7120 / (1000-sheet finisher)
AK-740 / (Bridge unit)
MT-730 / (Mailbox)
PH-7A/C/D / (Punch unit)
DT-730(B) / (Document tray)
FAX System 12

2RG/2RH
1-1-1
1-1 Specifications
1-1-1 Specifications
Main unit
Items Specifications
30 ppm model 35 ppm model
Type Desktop
Printing Method Dry static electric transfer (laser)
Paper
Weight
Cassette 52 to 163 g/m2
Multi Pur-
pose Tray 45 to 256 g/m2(Less than A4/Letter), 230 μm(Postal card) 52 to 163 g/m2(lager than A4/Letter)
Media type
Cassette Plain, Thin, Recycled, Preprinted, Bond, Color (Colour), Prepunched, Let-
terhead, Thick, High Quality, Custom, (Duplex:Same as Simplex)
Multi Pur-
pose Tray
Plain, Transparency (OHP film), Thin, Labels, Recycled,Preprinted, Bond,
Cardstock, Color (Colour), Prepunched,Letterhead, Envelope, Thick, High
Quality, Custom
Paper Size
Cassette A3, A4-R, A4, A5-R, B4, B5-R, B5, 216×340 mm, Ledger, Letter-R, Letter,
Legal, Statement-R, Oficio II, Folio, 8K, 16K-R, 16K
Multi Pur-
pose Tray
A3, A4-R, A4, A5-R, A6-R, B4, B5-R, B5, B6-R, 216×340 mm, Ledger
Letter-R, Letter, Legal, Statement-R, Executive, Oficio II, Folio, 8K, 16K-R,
16K,ISO B5, Envelope #10, Envelope #9, Envelope #6, Envelope Monarch,
Envelope DL, Envelop C5, Envelope C4, Hagaki (Cardstock), Oufuku
Hagaki (Return postcard), Youkei 4, Youkei 2, Custom 1 to 4(98 × 148 mm
to 297 × 432 mm)
Printable Area The point 3±2.5 mm, The back point 3±2.5 mm, left/right less than 4 mm
Warm-up
Time
(23°C,
60%RH)
Power on 18 seconds or less
Low Power 15 seconds or less
Sleep 15 seconds or less
Paper
Capacity
Cassette 550 sheets (64 g/m2) *1
500 sheets (80 g/m2) *1
Multi Pur-
pose Tray 100 sheets (A4/Letter or smaller)(80 g/m2)
25 sheets (lager size than A4/Letter)(80 g/m2)
Outputpaper
tray
Capacity
Inner Tray 250 sheets (80 g/m2)
Job separa-
tor 50 sheets (80 g/m2)
Light source White LED
Scanning method Flat surface scanning by the CCD image sensor
Photoconductor a-Si drum (diameter 30 mm)
Image Write System Semiconductor laser system
Charging system AC+DC charger roller system
Developer system Monocomponent jumping developer system
Toner supply system: Automatic replenishing from the toner container
Transfer system Transfer roller system

2RG/2RH
1-1-2
*1: *1: Up to upper limit height line in the cassette.
*2: *2: When two optional interface are installed, a fax line can not be installed.
*3: When IB-50 or IB-51 is installed, only one fax line can be installed.
Separation system Small diameter separation and separation needle (Impressing DC voltage)
Cleaning system Counter blade system
Charge erasing system Exposure by cleaning lamp (LED)
Fusing system Heat and pressure fusing with the heat roller and the press roller
Heat source: halogen heater
Abnormally high temperature protection devices: thermostat
Memory 2.0GB
Large capacity storage SSD 32GB: SSD 8 GB / Hard Disk 320GB
Inter
Interface
Standard
USB Interface Connector: 1 (Hi-Speed USB) *3
Network interface: 1
(10 BASE-T/100 BASE-TX/1000 BASE-T)
Hi-Speed USB: 4 (USB Flash memory slot)
Option eKUIO: 2 *2 Fax: 2 *3
Wireless LAN: 1
Operating
Environment
Temperature 10 to 32.5°C/50 to 90.5°F
Humidity 15 to 80%RH
Above the
sea level 2,500m/11,482 ft maximum
Brightness 1,500 lux maximum
Dimensions
Dimension (W × D × H) 594 × 696 × 680mm
Weight Approx. 58kg (without toner container)
Space Required (W × D) 31.82" × 19.97" 873 × 696mm (Using multi purpose tray)
Power source 100V AC,50/60Hz,13.0A 120V AC,60Hz,11.6A
220-240V AC,50/60Hz,6.5A
Items Specifications
30 ppm model 35 ppm model

2RG/2RH
1-1-3
Copy Functions
Items Specifications
30 ppm model 35 ppm model
Copy Speed
A4/Letter 30 sheets/min 35 sheets/min
A4R/Letter R 22 sheets/min 26 sheets/min
A3/Ledger 15 sheets/min 17 sheets/min
B4/Legal 15 sheets/min 17 sheets/min
B5 30 sheets/min 35 sheets/min
B5R 20 sheets/min 24 sheets/min
A5R 15 sheets/min 17 sheets/min
First Copy Time
(The main unit cassette
paper feed, A4)
Less than 3.6 seconds (Except the system safety time after the main power
switches on)
Zoom Level Manual mode: 25 to 400%, 1% increments Fixed zoom rate: 400%, 200%, 141%, 122%, 115%, 100%, 86%, 81%,
70%, 50%, 25%
Continuous Copying 1 to 999 sheets
Resolution 600 × 600 dpi, 9600 dpi equivalent × 600 dpi
Supported Original Types Sheet, Book, 3-dimensional objects (maximum original size: A3/Ledger)
Original Feed System Fixed

2RG/2RH
1-1-4
Printer Functions
Scanner Functions
*1 When using the document processor (Dual Scan DP) (except TWAIN scanning)
*2 Available OS: Windows XP/Windows Vista/Windows Server 2003/Windows Server 2008/Windows Server
2008 R2/Windows 7/Windows 8/Windows 8.1/Windows 10/Windows Server 2012/Windows Server 2012 R2
*3 Supported OS: Windows Vista/Windows Server 2008//Windows Server 2008 R2/Windows 7/Windows 8/
Windows 8.1/Windows 10/Windows Server 2012/Windows Server 2012 R2
Items Specifications
30 ppm model 35 ppm model
Printing Speed Same as Copying Speed.
First Print Time
(The main unit cassette
paper feed, A4)
Less than 4.2 seconds (Except the system safety time after the main power
switches on)
Resolution 600×600dpi
Operating System Windows XP, Windows Server 2003, Windows Vista, Windows 7, Windows 8, Windows 8.1, Windows 10, Windows Server 2008/R2, Windows Server
2012/R2?Mac OS 10.5 or later
Interface
USB Interface Connector: 1 (Hi-Speed USB)
Network interface: 1
(1000 BASE-T/100 BASE-TX/10 BASE-T (IPv6, IPv4, IPSec), 302.3az sup-
ported)
Optional Interface (Option): 2 (For IB-50/IB-51 mounting)
Wireless LAN (Option): 1 (For IB-35 mounting)
Page Description Language PRESCRIBE
Emulations PCL6 (PCL-XL/PCL-5c), KPDL3 (PostScript3 compatible), PDF, XPS,
Open XPS
Items Specifications
Resolution 600 dpi × 600 dpi, 400 dpi × 400 dpi, 200 dpi × 400 dpi, 300 dpi × 300 dpi,
200 dpi × 200 dpi, 200 dpi × 100 dpi
File Format TIFF, JPEG, XPS, Open XPS, PDF (MMR/JPEG compression/High com-
pressive PDF/OCR Text Recognition PDF(Option))
The consecutive originals
Reading velocity
(A4, 300 dpi, Image quality
Text/Photo mode)
1-side: B/W 80 images/min, Color 80 Images/min
2-sided: B/W 160 Images/min, Color 160 Images/min
Interface Ethernet (10 BASE-T/100 BASE-TX/1000 BASE-T)
Network protocol TCP/IP
Transmission Protocol SMB, SMTP, FTP, FTP over SSL, TWAIN*2, WIA*3, WSD

2RG/2RH
1-1-5
Document Processor
Paper Feeder (500-sheet × 2)
Items Specifications
Automatic 2-Sided dual scan
Type DP-7100 DP-7120 DP-7110
Document feed method Automatic feed
Supported Original Types Sheet originals
Paper Size
Maximum: A3/Ledger (297 × 432 mm) (Long-sized: 297 × 1,900 mm)
Minimum:
A6-R/Statement-R
(105 × 148 mm)
Minimum:
A5-R/Statement-R
(140 × 182 mm)
Minimum:
A6-R/Statement-R
(105 × 148 mm)
Paper Weight 1-sided: 35 to 160 g/m²
2-sided: 50 to 120 g/m² 1-sided: 45 to 160 g/m² 2-sided: 50 to 120 g/m² 1-sided: 35 to 220 g/m² 2-sided: 50 to 220 g/m²
Loading Capacity 140 sheets maximum
(50 to 80 g/m2)*1 50 sheets maximum
(50 to 80 g/m2)*1 270 sheets maximum (50 to 80 g/m2)*1
Dimensions
Dimension (W × D × H) 593 × 531 × 138.5 mm /
23.35" × 20.91" × 5.46" 600 × 502 × 128 mm / 23.35" × 20.91" × 5.46" 600 × 513 × 170 mm / 23.35" × 20.91" × 5.46"
Weight Approx. 9 kg Approx. 7.5 kg Approx. 14.5 kg
Items Specifications
Paper Supply system Feed & reverse roller system (Store Sheets: 550 sheets(64 g/m²)×2 cassettes / 500 sheets(80g/m²)× 2
cassettes)
Paper Size A3, A4-R, A4, A5-R, B4, B5-R, B5, 216×340 mm, Ledger, Letter-R, Letter,
Legal, Statement-R, Oficio II,Folio, 8K, 16K-R, 16K
Supported Paper Paper weight: 60 to 256 g/m²
Media types: Plain, Recycled, Thick
Dimensions
Dimension (W × D × H) 590 × 589 × 332 mm
Weight Approx. 20 kg

2RG/2RH
1-1-6
Large Capacity Feeder (1,500-sheet × 2)
1,000-Sheet Finisher
Items Specifications
Paper Supply Method Feed & reverse roller system
(Store Sheets: 3,500 sheets(64 g/m²) / 3.000 sheets(80g/m²))
Paper Size A4, B5, Letter
Supported Paper Paper weight: 60 to 256 g/m²
Media types: Plain, Recycled, Thick
Dimensions
Dimension (W × D × H) 590 × 626.9 × 332 mm
Weight Approx. 29 kg
Items Specifications
Number of Trays 1 tray
Paper Size
(80 g/m2)
Finisher
Tray
(When no
stapling)
A3, A5-R, B4, B5-R, B6-R, 216×340 mm, Ledger, Legal, Statement-R
Executive, Oficio II, Folio, 8K, 16K-R: 500 sheets
A4-R, A4, B5, B6-R, Letter-R, Letter, 16K: 1,000 sheets
Paper thickness When stapling: 90 g/m² or less
Stapling
Number of
sheets to
limit
A3, B4, B5-R, 216×340 mm, Ledger
Legal, Oficio II, 16K-R, 8K 30 sheets (52 to 105 g/m²) 2 cover sheets only (106 to 300 g/
m²)
A4-R, A4, B5, Letter-R, Letter, 16K 50 sheets (52 to 90 g/m²)
40 sheets (91 to 105 g/m²)
2 cover sheets only (106 to 300 g/
m²)
Media type Plain, Recycled, Preprinted, Bond, Color,Prepunched, Letterhead, Thick,
Coated, High Quality, Custom
Dimensions
Dimension (W × D × H) 548 × 618.5 × 1,050 mm
Weight Approx. 30 kg or less
Machine space measure (W
× D) 666 × 618.5 mm (with the tray pulled out)