Kyocera FS-C1020MFP Original instructions

A-1
English
Information
Introduction
This manual contains detailed instructions and notes on the operation and use
of this machine. For your safety and benefit, read this manual carefully before
using the machine. Keep this manual in a handy place for quick reference.
Important
Contents of this manual are subject to change without prior notice. In no event
will the company be liable for direct, indirect, special, incidental, or consequen-
tial damages as a result of handling or operating the machine.
-Notes:
Some illustrations in this manual might be slightly different from the machine.
Certain options might not be available in some countries. For details, please con-
tact your local dealer.
Depending on which country you are in, certain units may be optional. For de-
tails, please contact your local dealer.
Caution
Use of controls or adjustments or performance of procedures other than those
specified in this manual might result in hazardous radiation exposure.
We recommend the use of our own brand supplies. We will not be liable for any
damage caused by the use of third party supplies in this machine.
Notes
Two kinds of size notation are employed in this manual. With this machine refer
to the metric version.
Power Source
220-240 V, 50/60 Hz, 6 A or more
Please be sure to connect the power cable to a power source as above.

A-2
Laws and Regulations
Legal Prohibition
Do not copy or print any item for which reproduction is prohibited by law.
Copying or printing the following items is generally prohibited by local law:
bank notes, revenue stamps, bonds, stock certificates, bank drafts, checks, pass-
ports, driver's licenses.
The preceding list is meant as a guide only and is not inclusive. We assume no
responsibility for its completeness or accuracy. If you have any questions con-
cerning the legality of copying or printing certain items, consult with your legal
advisor.
This machine is equipped with a function that prevents making counterfeit bank
bills. Due to this function the original images similar to bank bills may not be
copied properly.
Laser Safety
This machine is considered class 1 laser device, safe for office / EDP use. The ma-
chine contains 6.2 milliwatt, 770 - 795 nanometer wavelength, AlGaAs laser di-
odes. Direct (or indirect reflected) eye contact with the laser beam might cause
serious eye damage. Safety precautions and interlock mechanisms have been de-
signed to prevent any possible laser beam exposure to the operator.
The following label is attached on rear side of the machine.
Direct (or indirect reflected) eye contact with the laser beam might cause serious
eye damage.

A-3
English
User Information on Electrical & Electronic Equipment
Users in the EU, Switzerland and Norway
Our Products contain high quality components and are designed to facilitate re-
cycling.
Our products or product packaging are marked with the symbol below.
The symbol indicates that the product must not be treated as municipal waste.
It must be disposed of separately via the appropriate return and collection sys-
tems available. By following these instructions you ensure that this product is
treated correctly and help to reduce potential impacts on the environment and
human health, which could otherwise result from inappropriate handling. Recy-
cling of products helps to conserve natural resources and protect the environ-
ment.
For more detailed information on collection and recycling systems for this prod-
uct, please contact the shop where you purchased it, your local dealer or
sales/service representatives.
All Other Users
If you wish to discard this product, please contact your local authorities, the
shop where you bought this product, your local dealer or sales/service repre-
sentatives.
Note for the Battery and/or Accumulator Symbol (For EU
countries only)
In accordance with the Battery Directive 2006/66/EC Article 20 Information for
end-users Annex II, the above symbol is printed on batteries and accumulators.
This symbol means that in the European Union, used batteries and accumulators
should be disposed of separately from your household waste.
In the EU, there are separate collection systems for not only used electrical and
electronic products but also batteries and accumulators.
Please dispose of them correctly at your local community waste collection/recy-
cling centre.

A-4
Safety Information
When using your machine, the following safety precautions should always be
followed.
In this manual, the following important symbols are used:
Environments Where the Machine Can be Used
RWARNING:
RCAUTION:
Note
❒When you use this machine for a long time in a confined space without good
ventilation, you may detect an odd smell. To keep the workplace comfortable,
we recommend that you keep it well ventilated.
❒To avoid possible build-up ozone, make sure to locate this machine in a large
well ventilated room that has an air turnover of more than 30 m3/hr/person.
Indicates a potentially hazardous situation which, if instructions are not followed, could result
in death or serious injury.
Indicates a potentially hazardous situation which, if instructions are not followed, may result
in minor or moderate injury or damage to property.
•Keep the machine away from flammable liquids, gases, and aerosols.
A fire or an electric shock might occur.
•Keep the machine away from humidity and dust. Otherwise a fire or an elec-
tric shock might occur. Do not place the machine on an unstable or tilted
surface. If it topples over, an injury might occur.
•Keep the machine in an area that is within optimum environmental condi-
tions. Operating the machine in an environment that is outside the recom-
mended ranges of humidity and temperature can cause an electrical fire
hazard. Keep the area around the socket free of dust. Accumulated dust
can become an electrical fire hazard.
•Make sure the room where you are using the machine is well ventilated and
spacious. Good ventilation is especially important when the machine is
used heavily.
•Machine is not suitable for desk work environments, so place the machine
in another room.
•When new, electrical devices containing volatile materials will normally re-
lease emissions into the air of their vicinity. For this reason, for the first few
days after installation of a new device, strong ventilation inside the room
where it is placed is necessary.

A-5
English
Handling Power Cords and Power Plugs
RWARNING:
RCAUTION:
•The supplied power cord is for use with this equipment only. Do not
use with other appliances. Doing so may result in fire, electric shock,
or injury.
•The wall outlet shall be installed near the machine and shall be easily
accessible.
•Connect the machine to the power source specified in this manual and
do not use any other power sources. Connect the power cord directly
to a wall outlet and do not use an extension cord. Power sources not
specified in this manual and extension cords are electric shock or fire
hazards.
•Power cords that are damaged, broken, modified, trapped under
heavy objects, pulled hard, or bent severely are electric shock and fire
hazards.
•Touching the prongs of the power cable's plug with anything metallic
constitutes a fire and electric shock hazard.
•Plug and unplug the power cable with dry hands, or an electric shock
could occur.
•When you disconnect the power plug from the wall outlet, always pull the
plug (not the cable).
•It is dangerous to handle the plug with wet hands. Doing this may result in
receiving an electric shock.
•Be sure to disconnect the plug from the wall outlet and clean the prongs and
the area around the prongs at least once a year. Allowing dust to build up
on the plug constitutes a fire hazard.

A-6
Handling the Machine
RWARNING:
RCAUTION:
•Wait at least 30 minutes after disconnecting the power plug before re-
moving the Transfer Unit.
•Before moving the machine, unplug the power cord from the wall outlet. If
the cord is unplugged abruptly, it could become damaged. Damaged plugs
or cords can cause an electrical or fire hazard.
•Unplug the power cord from the wall outlet before you move the machine.
While moving the machine, you should take care that the power cord will
not be damaged under the machine.
•The machine weighs approximately 30 kg (66.2 lb.). When moving the ma-
chine, use the inset grips on both sides, and lift slowly in pairs. The machine
will break or cause injury if dropped.
•When moving the machine, use the inset grips on both sides. The machine
will break or cause injury if dropped.
•When moving the machine after use, do not take out any of the toners, nor
the waste toner bottle to prevent toner spill inside the machine.
•Do not connect the Ethernet port of the machine to a network that may sup-
ply excess voltage, such as a telephone line. Doing so may result in fire or
electric shock.
•Be careful not to trap your fingers when opening or closing the top cover.

A-7
English
Handling the Machine's Interior
RWARNING:
RCAUTION:
•Do not attempt any maintenance or troubleshooting other than that
mentioned in this manual. This machine contains a laser beam gener-
ator and direct exposure to laser beams can cause permanent eye
damage.
•The inside of this machine becomes very hot. Do not touch parts labelled
“v” (indicating a hot surface).
•The fusing section of this machine might be very hot. Caution should be tak-
en when removing misfed paper.
•Lifting the paper feed unit carelessly or dropping it may cause injury.
•Do not pull out the paper tray forcefully. If you do, the tray might fall and
cause an injury.
•Before installing the memory unit, turn off the machine's power switch and
unplug the power cable. After installing the memory unit, be sure to close
the memory unit cover, and then turn the machine back on. Do not turn on
the machine before closing the memory unit cover.

A-8
Handling the Consumables
RWARNING:
RCAUTION:
•Do not incinerate used toner or toner containers. Toner dust might ig-
nite when exposed to an open flame. Dispose of used toner containers
in accordance with local regulations.
•Do not store toner, used toner, or toner containers in a place with an
open flame. The toner might ignite and cause burns of a fire.
•Do not incinerate spilled toner or used toner. Toner dust might ignite
when exposed to an open flame.
•Keep the polythene materials (bags, gloves, etc.) supplied with this
machine away from babies and small children at all times. Suffocation
can result if polythene materials are brought into contact with the
mouth or nose.
•Keep toner (used or unused) and toner containers out of reach of children.
•If toner or used toner is inhaled, gargle with plenty of water and move into
a fresh air environment. Consult a doctor if necessary.
•If toner or used toner gets into your eyes, flush immediately with large
amounts of water. Consult a doctor if necessary.
•If toner or used toner is swallowed, dilute by drinking a large amount of wa-
ter. Consult a doctor if necessary.
•Avoid getting toner on your clothes or skin when removing a paper jam or
replacing toner. If your skin comes into contact with toner, wash the affected
area thoroughly with soap and water.
•If toner gets on your clothing, wash with cold water. Hot water will set the
toner into the fabric and may make removing the stain impossible.
•Our products are engineered to meet high standards of quality and function-
ality, and we recommend that you use only the expendable supplies avail-
able at an authorized dealer.

A-9
English
Safety Labels of This Machine
This section explains the machine's safety information labels.
Positions of RWARNING and RCAUTION labels
This machine has labels for RWARNING and RCAUTION at the positions
shown below. For safety, please follow the instructions and handle the machine
as indicated.
Do not touch labelled gray areas.
The areas can get very hot.
Do not touch labelled gray areas.
The areas can get very hot.
BPC063S

A-10
Do not incinerate used toner or toner containers. Toner dust might ignite when
exposed to an open flame. Dispose of used toner containers in according with lo-
cal regulations.
Keep toner (used or unused) and toner containers out of reach of children.
Be careful not to trap your fingers when opening or closing the top cover.
The machine weighs approximately 30 kg (66.2 lb.). When moving the machine,
use the inset grips on both sides, and lift slowly in pairs.
Do not incinerate used toner or toner containers. Toner dust might ignite when
exposed to an open flame. Dispose of used toner containers in according with lo-
cal regulations.
Keep toner (used or unused) and toner containers out of reach of children.
Power Switch Symbols
The meanings of the symbols for the switches on this machine are as follows:
•a:POWER ON.
•b:POWER OFF.

A-11
English
Noise Emission *1
❖Sound Power Level
❖Sound Pressure Level *2
*1 The preceding measurements made in accordance with ISO7779 are actual values.
*2 Measured at the position of a bystander.
During Monochrome Printing (Main Unit Only) 63 dB (A) or less
During Color Printing (Main Unit Only) 64 dB (A) or less
Standby (Main Unit Only) 40 dB (A) or less
During Printing (Complete System) 68 dB (A) or less
During Monochrome Printing (Main Unit Only) 57 dB (A) or less
During Color Printing (Main Unit Only) 58 dB (A) or less
Standby (Main Unit Only) 34 dB (A) or less
During Printing (Complete System) 62 dB (A) or less

A-12
ENERGY STAR Program
This machine is equipped with the following Energy Saver modes: Energy Saver
mode 1 and Energy Saver mode 2. The machine recovers from Energy Saver
mode when it receives a print job, prints a received fax, or when the {Copy},
{Color Start}, or {B&W Start}key is pressed.
❖Energy Saver mode 1
This machine automatically enters Energy Saver mode 1 about 30 seconds af-
ter the last operation is completed.
❖Energy Saver mode 2
This machine automatically enters Energy Saver mode 2 2 minutes after the
last operation is completed.
❖Specifications
ENERGY STAR®Program Requirements for Imaging Equipment
The ENERGY STAR®Program Requirements for Imaging Equipment encourages energy con-
servation by promoting energy efficient computers and other office equipment.
The program backs the development and dissemination of products that feature energy saving
functions.
It is an open program in which manufacturers participate voluntarily.
Targeted products are computers, monitors, printers, facsimiles, copiers, scanners, and multi-
function devices. Energy Star standards and logos are internationally uniform.
Energy Saver mode 1 Power Consumption 110 W or less
Default Time 30 seconds
Recovery Time 10 seconds or less
Energy Saver mode 2 Power Consumption 25 W or less
Default Time 2 minutes
Recovery Time 48 seconds or less

A-13
English
Note
❒For details about how to configure Energy Saver mode, see “Administrator
Settings”, User Guide in the CD-ROM.
❒If the machine is in Energy Saver mode 2 for 24 hours continuously, the
machine automatically returns to normal state and performs self-mainte-
nance.
Reference
“Administrator Settings”, User Guide in the CD-ROM
❖Recycled Paper
This device supports the recycled paper which reduces the load on the envi-
ronment. Your service representative can provide information about recom-
mended paper types.

A-14
Others
Symbols
DECLARATION OF CONFORMITY
TO
2004/108/EC, 2006/95/EEC, 93/68/EEC and 1999/5/EC
We declare under our sole responsibility that the product to which this declara-
tion relates is in conformity with the following specifications.
EN55024
EN55022 Class B
EN61000-3-2
EN61000-3-3
EN60950-1
EN60825-1
TBR-21
EG201121 AN14R00
❖NOTICE TO USERS (NEW ZEALAND)
• The grant of a Telepermit for any item of terminal equipment indicates
only that Telecom has accepted that the item complies with minimum con-
ditions for connection to its network. It indicates no endorsement of the
product by Telecom, nor does it provide any sort of warranty. Above all, it
provides no assurance that any item will work correctly in all respects with
another item of Telepermitted equipment of a different make or model, nor
does it imply that any product is compatible with all of Telecom's network
services.
• This equipment is not capable, under all operating conditions, of correct
operation at the higher speeds for which it is designed. Telecom will accept
no responsibility should difficulties arise in such circumstances.
• This equipment shall not be set up to make automatic calls to the Telecom
“111” Emergency Service.
• If a charge for local calls is unacceptable, the “Dial” button should NOT be
used for local calls. Only the 7-digits of the local number should be dialled
from your telephone. DO NOT dial the area code digit or the “0” prefix.
• This equipment may not provide for the effective hand-over of a call to an-
other device connected to the same line.
• This device may be subject to ringing or bell tinkle when calls are made
from another device on the same line. If this occurs, the problem SHOULD
NOT be referred to the Telecom Faults Service.

A-15
English
• This equipment should not be used under any circumstances, which may
constitute a nuisance to other Telecom customers. For example, repeated
attempts to make unsolicited sales offers to the same number or group of
numbers, such as when a block of numbers terminate on the same PABX.
• The call log incorporated in this equipment does not record all answered
calls. The call log, therefore may not agree with the Telecom account which
may include calls not shown on the log.
• Not all telephones will respond to incoming ring when connected to the
extension socket.

A-16

A-17
English

A-18
MEMO

B-1
Deutsch
Informationen
Einleitung
Dieses Manual enthält detaillierte Anweisungen und Hinweise zum Betrieb
dieses Geräts. Lesen Sie zu Ihrer Sicherheit und Ihrem Schutz dieses Manual vor
der Verwendung des Geräts sorgfältig durch. Bewahren Sie dieses Manual für
evtl. Fragen griffbereit auf.
Wichtig
Der Inhalt dieses Manuals kann ohne Ankündigung geändert werden. Das
Unternehmen ist in keiner Weise haftbar für direkte, indirekte, konkrete,
zufällige oder Folgeschäden, die durch Handhabung oder Betrieb des Geräts
entstehen.
-Hinweise:
Einige Abbildungen in diesem Manual könnten etwas unterschiedlich vom
Gerät sein.
Bestimmte Optionen sind in einigen Ländern nicht verfügbar. Weitere
Informationen erhalten Sie bei Ihrem örtlichen Händler.
Abhängig von Ihrem Aufenthaltsland könnten manche Einheiten optional sein.
Weitere Informationen erhalten Sie bei Ihrem örtlichen Händler.
Vorsicht
Die Verwendung anderer als der in diesem Manual beschriebenen Steuerungen,
Einstellungen oder Vorgänge könnte gefährliche Strahlung hervorrufen.
Wir empfehlen Ihnen die Verwendung unseres Originalzubehörs. Wir sind
nicht haftbar für Schäden, die durch die Nutzung von Zubehör von
Drittanbietern mit diesem Gerät entstehen.

B-2
Hinweise
In diesem Manual werden zwei Formatangaben verwendet. Richten Sie sich bei
diesem Gerät nach der metrischen Version.
Stromversorgung
220-240 V, 50/60 Hz, 6 A oder mehr
Schließen Sie das Netzkabel wie oben dargestellt an eine Steckdose an.