Kyocera KD135GX-LPU - MOUNTING GUIDE User manual

KKM-SM-0512
MOUNTING GUIDE
FOR THE
SOLAR PHOTOVOLTAIC POWER MODULES
Please read this guide carefully before installing the modules.
2009.12.01
KD series modules may be attached to a support structure
by the following methods. Detailed mounting method is
described in ‘mounting table’.
For optimal performance in all applications, clearance
between the module frame and the mounting surface is
required to allow cooler ambient air to circulate around the
back of the module and to avoid the module and / or wiring
damage.
The minimum spacing of .6” (15 mm) is required between
PV module and the mounting surface around the perimeter
of PV module. There should also be a clearance of at
least .13” (3.2 mm) between the individual modules to allow
heat-related expansion.
BOLTING: Utilizing 5/16” or 8 mm stainless steel hardware
through the existing .35” (9 mm) diameter mountingholes in
the module frame and then through module mounting holes
on the support structure. Tighten the screws with adequate
torque (132 in-lb).
Refer to the Module Drawings for the position of the solar
module mounting holes.
CLAMPING: Fasten modules firmly with clamps using
torque values specified by structure manufacturers.
Top-down clamps must have a minimum 40mm clamping
width, and minimum 9mm overlap onto module frame.
Clamps also must not shade the sunlight incidence on glass
surface. Clamp material must be either stainless steel or
anodized aluminum.
KD135SX-UPU, KD135GX-LPU～KD215GX-LPU

KKM-SM-0512
Long Side ShortSide
Bolting
Top Down
Clamp
Continuous
Clamp
<KD205GX-LPU,KD210GX-LPU,
KD215GX-LPU >
:
943mm
100mm 100mm 100mm 100mm
278.5mm 943mm
100mm 100mm 100mm 100mm
278.5mm
943mm
100mm 100mm 100mm 100mm
278.5mm 943mm
100mm 100mm 100mm 100mm
278.5mm
100mm 200mm
943mm278.5mm
100mm 200mm
943mm278.5mm
100mm 200mm
943mm278.5mm
100mm 200mm
943mm278.5mm
200mm 100mm
943mm
278.5mm
200mm 100mm
943mm
278.5mm
200mm 100mm
943mm
278.5mm
200mm 100mm
943mm
278.5mm
943mm278.5mm 943mm278.5mm
943mm278.5mm 943mm278.5mm
continuous clamp
:
Permissible
clamping range
Mountingtable- 1
150mm
150mm 150mm 150mm
150mm
150mm 150mm 150mm

KKM-SM-0512
Bolting
<KD185GX-LPU>
Mountingtable- 2
:
:
Permissible
clamping range
825mm256.5mm 825mm256.5mm
100mm
256.5mm 825mm
100mm 100mm100mm 100mm
256.5mm 825mm
100mm 100mm100mm
100mm
256.5mm 825mm
100mm 100mm100mm 100mm
256.5mm 825mm
100mm 100mm100mm
825mm256.5mm 825mm256.5mm
825mm
200mm 200mm
256.5mm 825mm
200mm 200mm
256.5mm
825mm
200mm 200mm
256.5mm 825mm
200mm 200mm
256.5mm
825mm
200mm 200mm
256.5mm 825mm
200mm 200mm
256.5mm
825mm
200mm 200mm
256.5mm 825mm
200mm 200mm
256.5mm
Long Side ShortSide
150mm
150mm 150mm 150mm
150mm
150mm 150mm 150mm
TopDown
Clamp
Continuous
Clamp
continuous clamp

KKM-SM-0512
Bolting
<KD135SX-UPU,KD135GX-LPU>
:
:
Permissible
clamping range
100mm
278.5mm 943mm
100mm 100mm
278.5mm 943mm
100mm
100mm
278.5mm 943mm
100mm 100mm
278.5mm 943mm
100mm
200mm
278.5mm 943mm
200mm
278.5mm 943mm
200mm
278.5mm 943mm
200mm
278.5mm 943mm
200mm
278.5mm 943mm
200mm
278.5mm 943mm
200mm
278.5mm 943mm
200mm
278.5mm 943mm
943mm
278.5mm 943mm 278.5mm
943mm
278.5mm 943mm 278.5mm
Long Side ShortSide
150mm 150mm 150mm 150mm
150mm 150mm 150mm 150mm
Mountingtable- 3
TopDown
Clamp
Continuous
Clamp
continuous clamp